LiftMaster ATS Support Question
LiftMaster ATS Support Question
Find answers below for this question about LiftMaster ATS.Need a LiftMaster ATS manual? We have 1 online manual for this item!
Question posted by trevorhahn on May 8th, 2017
Door Opener Only Moves 6 Inches
Opener Only Moves 6 Inches The Eyes Are Good And Down Force Is All The Way Up
Current Answers
Answer #1: Posted by techyagent on May 8th, 2017 9:01 PM
techyagent
Member since:
June 17th, 2014 Points: 4,799,780
Member since:
June 17th, 2014 Points: 4,799,780
This is a known problem you need to check the link below
Thanks
Techygirl
Related LiftMaster ATS Manual Pages
ATS2113X Manual - Page 1
....liftmaster.com
®
COMMERCIAL DOOR OPENER Model ATS 2113X 1/2 HP
For Residential And Light Duty Commercial Use Install on Sectional Doors Only
L
O
W
H
I
L
G
A
H NO R M
FOURPCE
L
O
W H
I
L
G
A
H NO R M
FDOORWCNE
Owner's Manual
■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■...
ATS2113X Manual - Page 2
... the travel limits 21 Adjust the force 22 Test the safety reversal system 23 Test the Protector System 23
Operation
24-28
Operation safety instructions 24 Using your garage door opener 24 Using the wall-mounted door control 25 To open the door manually 25 Care of your garage door and/or the garage door opener if you do not comply with...
ATS2113X Manual - Page 3
... INJURY could result from the use on one piece garage doors. Sectional Door
To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and
operating the opener. • ONLY operate garage door opener at 120V, 60 Hz to exceed 168 sq. Maximum door size 14 ft. Preparing your garage door
Before you begin:
• Disable locks.
• Remove any...
ATS2113X Manual - Page 5
... will depend on the model purchased.
Carton Inventory
Your garage door opener is packaged in the foam. Parts may be stuck in...Bracket With Square Holes (2)
Rail Motor Unit
Straight Door Arm
Chain Pulley Bracket
Trolley
Safety Labels and
Literature
The Protector System® (2) Safety Reversing Sensors (1 Sending Eye and 1 Receiving Eye) with 2-Conductor White & White/Black Bell Wire...
ATS2113X Manual - Page 6
... a 45° angle to opener so one hole in rail
and motor unit line up. • Thread one of any other bolts will cause serious damage to door opener. • Align rail over chain spreader and opener sprocket. Use of the washered bolts part way in rail support. Cut tape from moving garage door opener:
• ALWAYS keep hand...
ATS2113X Manual - Page 7
... of 5 feet (1.5 m).
• away from ALL moving parts of the door.
10. Install garage door opener 7 feet (2.13 m) or more above floor.
7. NEVER wear watches, rings or loose clothing while installing or servicing opener. Install wall-mounted garage door control:
• within sight of the garage door.
• out of reach of garage door.
12. If the chain
returns to cables...
ATS2113X Manual - Page 10
...hold the opener securely on the trolley release arm to
determine the
correct mounting
height from ceiling.
You will need help at is in the way you raise the door, pull... the Rail to secure. NOTE: If the door spring is convenient for setting an ideal door-to garage door, rest garage door opener rail on 2x4 placed on the garage floor below the header bracket. Trolley
ENGAGED...
ATS2113X Manual - Page 11
..."
Nut 5/16"-18
Bracket (Not Provided)
- This bracket and fastening hardware are shown. Measure the distance from a falling garage door opener, fasten it SECURELY to make sure the rail is not centered above the door).
7. Cut both pieces of the motor unit to the hanging brackets with the header bracket if the bracket is...
ATS2113X Manual - Page 13
... Light
• Install a 75 watt maximum light bulb in the top of the red handle so "NOTICE" reads right side up as shown. Secure with a "Garage Door Opener" bulb. NOTE: If it is necessary to pull door open door falling rapidly and/ or unexpectedly.
• NEVER use emergency release handle unless...
ATS2113X Manual - Page 14
... into a grounding type outlet. RIGHT
WRONG
PERMANENT WIRING CONNECTION
If permanent wiring is required by your garage door opener has a grounding type plug with ALL local electrical and building codes.
• NEVER use an extension ...cord, 2-wire adapter, or change plug in ANY way to the screw on the silver terminal; To make it fit outlet. and the ...
ATS2113X Manual - Page 15
... floor
15 This required safety device MUST NOT be securely fastened to full open position, and the opener lights will move in the down direction. above the floor. The sending eye transmits an invisible light beam to the garage door opener BEFORE installing the safety reversing sensor. Either can be unobstructed. If it is NOT...
ATS2113X Manual - Page 17
... sensor (Figure 9).
• Connect the pre-installed wires to the sensor wires with lenses pointing toward each other across the door (Figure 6).
• Use wing nuts to fasten sensors to the garage door opener.
Make sure that you choose the same color pre-installed wires for the safety reversing sensors, follow the instructions below...
ATS2113X Manual - Page 18
... to garage door opener: • Strip 1/4" (6 mm) of insulation from each set of alignment or obstruction. Separate white and white/black wires sufficiently to connect to the opener terminal screws: white to 2 and white/black to Opener Terminal Screws
Bell Wire
1. Strip wire 1/4" (6 mm)
1/4" (6 mm)
2.
If the receiving eye indicator light is closing, the door...
ATS2113X Manual - Page 21
... a complete travel cycle. • Does the door open completely but opens at least 5 feet (1.5 m): Increase up or down travel (including binding or unbalanced doors), it will stop when moving up travel . NOTE: Repeated operation of safety reversal system.
• If one control (force or travel cycle: If the opener lights are flashing, the safety reversing sensors...
ATS2113X Manual - Page 22
... halfway through down (close) cycle and the opener lights aren't flashing, INCREASE DOWN (close ) force by a closing garage door. • Too much force on a 1-1/2" (3.8 cm) obstruction. Turn force adjustment controls with the door's upward travel .
Make small adjustments until the door completes a close the door. Without a properly installed safety reversal system, persons...
ATS2113X Manual - Page 23
...;oor, centered under the garage door.
• Operate the door in the down position.
Without a properly installed safety reversing sensor, persons (particularly small children) could be tested. Safety Reversing Sensor 23
Safety Reversing Sensor The door will not move more than an inch (2.5 cm), and the opener lights will not close the door. See the illustration on page...
ATS2113X Manual - Page 24
... release them until the door starts to move .
• The Wall-Mounted Door Control: Hold the push button or bar down until down travel is broken. Garage door MUST reverse on contact with any of children. Failure to garage door opener BEFORE making ANY repairs or removing covers.
15. Activate your garage door opener, it will open , the door will reverse. If closed...
ATS2113X Manual - Page 29
... be circumvented.
You may set up this Security✚® garage door opener is operated with those accessories.)
Instructions are Described and Illustrated Below
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep gate or garage door in the garage door opener does not authorize the purchaser or supplier of the non-rolling code...
ATS2113X Manual - Page 30
... your garage door opener. Release the button when the motor unit lights blink. Release the # button.
2.
The opener light will blink once when the temporary PIN has been learned.
The opener light will...✽ button. Test by visitors or service people with a temporary 4-digit PIN. The door should move . To set the number of times this temporary PIN will work , press the number ...
ATS2113X Manual - Page 31
... anyone to cross path of closing garage door:
• Install door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of door.
• NEVER permit children to operate or play with paper
opener light on the motor unit panel is
Door Control
activated. on and then...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 8 months ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
I Have An Ats 211 Opener And I Have Replaced The Rpm Sensor, Main Board,
I have adjusted the down force knob to the fullest . I have even called a service tech out and he ca...
I have adjusted the down force knob to the fullest . I have even called a service tech out and he ca...
(Posted by Lbimhoff 9 years ago)
Door Won't Shut By Remote
Door opens fine. light stays on all the time you have to hold wall door button to shut door. Would t...
Door opens fine. light stays on all the time you have to hold wall door button to shut door. Would t...
(Posted by dwightoverton 10 years ago)