GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by bagelmom3 on August 21st, 2011
Sensor Beeping
There is a fire sensor beeping and I cannot dissable it. Is there a silence button?
Current Answers
Answer #1: Posted by antiroach on August 21st, 2011 4:36 PM
antiroach
Member since:
July 23rd, 2011 Points: 369,520
Member since:
July 23rd, 2011 Points: 369,520
Here's a possible reason and solution:
"Your alarm system has two power sources, a power transformer that is plugged into an electrical outlet and a backup battery that is located within the control panel box. If the battery is over five years old you will need to replace it. Open the box and you you will see the battery with a set of wires attached to it. Pull the wires off of the battery and take it to a local battery warehouse supply store. They will match it up with a new one. Plug the new battery into the system and your system should restore itself back to normal."
It's also possible that you need to swap out the touchpad. For info on how to do so, you can go here and a new touchpad is here.
Nerds need love too...
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
... speaker provides alarm, status, and button-press sounds. Touchpad Wire Length Between Touchpad and Panel
750 feet 300 feet
1 A built-in an environmentally controlled area (32°F to 120°F/0°C to indicate the current status of compatible security systems (see the "Specifications" section).
Table 1: Touchpad Power Usage
Current (mA) 110
60 12
Conditions
Maximum...
Installation Instructions - Page 2
... in the wall in the wire access area of the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Connect the touchpad +12V, BUS A, BUS B, and GND terminals to the Mounting Plate
Align the tabs at the marked locations where studs are...
Installation Instructions - Page 3
... SECURITY. 5. For installations that all wiring between the touchpad and the panel. Power Up and Bus Communication
Note Steps 3 through all bus device addresses until the touchpad appears.
8. The following example shows what a device address display may look like: UNIT - The touchpad should display SYSTEM PROGRAMMING.
4.
Verify that don't include an alphanumeric touchpad as key beeps...
Installation Instructions - Page 4
... fire departments. Test the touchpad by arming/disarming the system, activating the touchpad panics, bypassing sensors, and by pressing the D and 6 buttons together for lighting conditions in the section "Changing the Touchpad Unit Number." The contrast adjustment lightens or darkens the text. The display shows SYSTEM MENU, then TIME AND DATE (Concord panels with software versions...
Installation Instructions - Page 5
...mode. The display shows ENTER _. 3. Note If the new touchpad unit number was previously learned by a switch. Check the touchpad display contrast setting. At the touchpad, press and hold the D and 6 buttons together for at touchpad and panel terminals.
2. Make sure touchpad unit number is plugged in Concord RF systems. 5.
Troubleshooting
Table 3 describes what to an unswitched...
Installation Instructions - Page 6
...;F (49°C) Maximum Humidity 95% relative, non-condensing Dimensions 5.0" x 4.50" x 0.75" (L x W x D) UL Listings (all other names are designed to another system touchpad and enter 8 + installer/dealer CODE (default = 4321) + 0 + 1. Concord is a trademark of the FCC Rules. FCC Part 15 Class B
This equipment has been tested and found to part 15 of GE...
Similar Questions
Alarm Is Not Hooked Up. However My Unit Won't Stop Beeping
(Posted by Cbeinke2 3 years ago)
Disable A Motion Sensor
Hi, i want to ask what i have to do to permanently disable a motion sensor.
Hi, i want to ask what i have to do to permanently disable a motion sensor.
(Posted by brwbondepalm 10 years ago)
I Have A Ge Atp 1000 Keypad. Can The Keypad Beeps Get Shut Off Or Lowered.
Also, is it possible to turning the beeping off when arming the system? Thanks, John
Also, is it possible to turning the beeping off when arming the system? Thanks, John
(Posted by jcangi01 12 years ago)
5150-w - Security Glassbreak Shock Sensor
Will thios sensor work on hurricane impact glass windows? If so, do yu have to install on each pane ...
Will thios sensor work on hurricane impact glass windows? If so, do yu have to install on each pane ...
(Posted by markkmd11 12 years ago)
Keypad Tones
The Keypad used tobeep when the buttons were pushed, however it does not do that anymore. I have tri...
The Keypad used tobeep when the buttons were pushed, however it does not do that anymore. I have tri...
(Posted by rbwoods 13 years ago)