GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by brwbondepalm on January 1st, 2014
Disable A Motion Sensor
Hi, i want to ask what i have to do to permanently disable a motion sensor.
Current Answers
Answer #1: Posted by cursed on January 1st, 2014 9:19 AM
cursed
Member since:
November 27th, 2013 Points: 320,075
Member since:
November 27th, 2013 Points: 320,075
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
... area (32°F to 120°F/0°C to indicate the current status of compatible security systems (see the "Specifications" section).
The door can be removed by the touchpad. • Table 2 describes the maximum wire lengths allowed between the touchpad and the panel. imum available power. • Table 1 describes the power used by simply...
Installation Instructions - Page 2
...Align the tabs at the marked locations where studs are not present. 4. Touchpad Wiring Connections
Attaching the Touchpad to 22-gauge wire from mounting properly. Figure 2. Align the mounting ...screw holes and secure the
back plate using the screws provided. 5. Wiring the Touchpad to pull the wiring cable through. Run a 4-conductor, 18- Be sure to the touchpad location (see Figure...
Installation Instructions - Page 3
...alphanumeric touchpad as a permanent part of the system, you can connect one for system programming to the Programming Touchpad Header on the panel. Alphanumeric touchpads briefly show the date and time display. The touchpad... the bus for the newly installed touchpad (such as a programming touchpad, be careful not to a Concord Express, Concord, or Concord Ultra panel with the cable). Upon...
Installation Instructions - Page 4
..., then press ƒ. TYPE 14-NONE 5. Test the touchpad by arming/disarming the system, activating the touchpad panics, bypassing sensors, and by pressing 8 + installer/dealer CODE + 0...system master CODE. Removing the programming touchpad from Concord panels with software versions 1.0-1.6:
To prevent a trouble condition, you must delete the programming touchpad unit number from the panel header....
Installation Instructions - Page 5
... bus devices and the panel:
• All bus devices with DIP switches (LED Touchpads, ESMs, HIMs, etc.) must be set to exit from touchpad.
1. Note At this page). (Concord panels with software versions 1.01.6 only.)
Changing the Touchpad Unit Number (Concord
Panels with the procedure. Ignore the failure and continue with Software Version 1.0-1.6 Only)
Use...
Installation Instructions - Page 6
...follows:
For systems where this equipment does cause harmful interference to radio communications. Compatibility Concord, Concord Express, Concord Ultra Power Requirements 12 VDC nominal (See Table 1 for more of GE Interlogix.... If this is encouraged to try to correct the interference by one touchpad,...
Similar Questions
Program Time And Date On Touchpad
(Posted by Samtalmer 12 years ago)
5150-w - Security Glassbreak Shock Sensor
Will thios sensor work on hurricane impact glass windows? If so, do yu have to install on each pane ...
Will thios sensor work on hurricane impact glass windows? If so, do yu have to install on each pane ...
(Posted by markkmd11 12 years ago)
Sensor Beeping
There is a fire sensor beeping and I cannot dissable it. Is there a silence button?
There is a fire sensor beeping and I cannot dissable it. Is there a silence button?
(Posted by bagelmom3 12 years ago)
How Can I Get An Install Pet Lenses On My Motion Sensor?
My motion sensor goes off every time I set it. I don't have pets, so it must be super sensitive.
My motion sensor goes off every time I set it. I don't have pets, so it must be super sensitive.
(Posted by scintron 12 years ago)
How Do We Disarm Our System And When Do We Type In Security Code?
(Posted by carolyn2707 13 years ago)