GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by Cbeinke2 on September 4th, 2020
Alarm Is Not Hooked Up. However My Unit Won't Stop Beeping
The person who posted this question about this GE product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by INIMITABLE on September 4th, 2020 4:59 PM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,077,740
Member since:
April 3rd, 2020 Points: 2,077,740
First, check to be sure your oven isn't too hot to touch. ... The timer beeps to alert you that your cooking time is up. On many models, the beeping will continue periodically to remind you to remove your food from the oven, since the timer does not turn the oven off
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...touchpad, allow at least 3 inches below it past its stop point.
Table 1: Touchpad Power Usage
Current (mA) 110
60 12
Conditions
Maximum alarm current with basic system operating commands. Touchpad Wire Length Between Touchpad... the touchpad in speaker provides alarm, status...touchpad. • Table 2 describes the maximum wire lengths allowed between the touchpad...
The touchpad includes ...
Installation Instructions - Page 2
... with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Remove panel AC and backup battery power. 2. Connect the touchpad +12V, BUS A, BUS B, and GND terminals ...
Mounting Holes
Note Do not overtighten screws or the mounting plate may bind and prevent the touchpad from the panel to the Mounting Plate
Align the tabs at the marked locations where studs ...
Installation Instructions - Page 3
...look like: UNIT - Then, use the appropriate procedure for System Programming Only
After making all wiring between the touchpad and the panel. Verify that don't include an alphanumeric touchpad as a permanent part of each bus device.
1. Alphanumeric touchpads briefly show the date and time display. Press ƒ and the display shows SECURITY. 5. After verifying the touchpad device ID...
Installation Instructions - Page 4
...unit number and its unit number from Concord panel memory before activating alarms, to 3 (brightest background), then press ƒ. 5. TYPE 14-NONE 5. Exit program mode and disconnect the programming cable from 0 (darkest background) to avoid dispatching local police and fire departments. Test the touchpad...then stops after pressing ƒ and displays the new set-
The touchpad ...
Installation Instructions - Page 5
... with software versions 1.01.6 only.)
Changing the Touchpad Unit Number (Concord
Panels with Software Version 1.0-1.6 Only)
Use the following guidelines when changing device unit numbers to avoid communication conflicts between the touchpad and the panel begins immediately. Make sure touchpad unit number is in configuration mode and no beeps when buttons are pressed. Enter the desired...
Installation Instructions - Page 6
... may cause harmful interference to radio or television reception, which can be cleared.
Concord is a trademark of the following measures:
‰ Reorient or relocate the receiving... Rules. The touchpad and all applied for): .....UL 985 Household Fire Warning System Units UL 1023 Household Burglar-Alarm System Units UL 1610 Central Station Burglar-Alarm Units (Commercial Burglary)...
Similar Questions
Help- I Moved Into A House And I Don't Have The Alarm Code. Won't Stop Beeping
(Posted by elisarooks 11 years ago)
240-coe Unit, Date Code 0544t Beeps And Blinks Green Light. Is There Replacement
My 240-COe unit just started beeping every 5 minuts with blinking green light. Once I press reset bu...
My 240-COe unit just started beeping every 5 minuts with blinking green light. Once I press reset bu...
(Posted by attamohammad2003 12 years ago)
I Have A Ge Atp 1000 Keypad. Can The Keypad Beeps Get Shut Off Or Lowered.
Also, is it possible to turning the beeping off when arming the system? Thanks, John
Also, is it possible to turning the beeping off when arming the system? Thanks, John
(Posted by jcangi01 12 years ago)
Sensor Beeping
There is a fire sensor beeping and I cannot dissable it. Is there a silence button?
There is a fire sensor beeping and I cannot dissable it. Is there a silence button?
(Posted by bagelmom3 12 years ago)
My Keypad Beeps 4xs A Day Every Min Until The Code Is Entered. How Do I Stop Thi
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
(Posted by nicholasadamsyoung 12 years ago)