TEAC IF-SM/DM Support and Manuals
Get Help and Manuals for this TEAC item
View All Support Options Below
Free TEAC IF-SM/DM manuals!
Problems with TEAC IF-SM/DM?
Ask a Question
Free TEAC IF-SM/DM manuals!
Problems with TEAC IF-SM/DM?
Ask a Question
Popular TEAC IF-SM/DM Manual Pages
TASCAM Pro Audio Brochure 2011 - Page 2
...and low-cut filter per track • Auto or manual cue points • Alert signal to headphone output ...rigors of location recording with no moving parts, and you can be with trims ...P82. For high-resolution music recording, a set of AES/EBU connectors is available for power...batteries. • Dual Compact Flash recording media supports backup, mirroring and seamless A/B recording
•...
TASCAM Pro Audio Brochure 2011 - Page 7
...to concert recording and commercial use.
• XLR mic inputs with tri-level
sync support for live , location and surround effect recordings. The user interface is the professional ...; 128x64 backlit LCD display • Powered through the built-in record or playback.
wheel settings for unpredictable timecode sources • Pull-up to house clock with phantom power and analog ...
IF-SM:DM Owner's Manual - Page 1
D00885000A
»
IF-SM/DM
Surround Monitor Card
OWNER'S MANUAL
This appliance has a serial number. Please record the model number and serial number and retain them for your records. Model number Serial number
IF-SM:DM Owner's Manual - Page 2
...Stereo to mono downmix 12 Figure 2.19: Example downmix screen showing attenuation points 13 Figure 2.20: Type 1 and Type 2 bass management for 5.1 and 6.1 settings 13 Figure 2.21: Example downmix screen showing attenuation points 14 Figure 3.1: Block diagram 17 Figure 3.2: Level diagram 18
2 TASCAM IF-SM/DM Owner's Manual Introduction
Installation 3 Connections 4 Monitor alignment 4
2 -
IF-SM:DM Owner's Manual - Page 3
...are installing more than one or two surround monitoring systems. It provides flexible setup capabilities, routing, downmix capabilities, bass management, and monitor setup, etc...cause damage to a qualified TASCAM distributor. TASCAM IF-SM/DM Owner's Manual 3 are removing a previously-fitted interface card, that you...guide rails and slide it from the slot into the slot.
IF-SM:DM Owner's Manual - Page 4
... must be a little stiff.
1 - This is set using the MONITOR ALIGNMENT screen, and the procedure is described...the rear panel of the unit).
5 Use the screws supplied with the LFE gain.
4 TASCAM IF-SM/DM Owner's Manual
Pin 1
2
3
4
5
6
7
8
9
10 11 12 13'
8+ 8Gnd 7- 6+ ...the rear panel of the unit.
6 Repeat the installation process for the IF-FW card, which interface cards ...
IF-SM:DM Owner's Manual - Page 5
... use the cursor and ENTER keys to a 2.1 setting • Setting the monitoring level • Setting SPL reference level
When a channel is here shown installed in slot 1, any reference to POD 4 should ...cursor and ENTER keys to be interpreted as SETUP TARGETs), and the lower half shows the settings for channel control
TASCAM IF-SM/DM Owner's Manual 5 Unmuted channels show an on the ...
IF-SM:DM Owner's Manual - Page 6
... switch, 2.1 switch or oscillator switch are on . Note that the SPL REFERENCE setting and monitor level settings are not available when the oscillator is routed in the BASS MANAGEMENT option) -...internal oscillator to the surround card outputs.
There are active. These
6 TASCAM IF-SM/DM Owner's Manual
time is not possible when this way.
Naturally, downmix is not possible with smaller ...
IF-SM:DM Owner's Manual - Page 7
...pattern, as set up the monitoring keys, and
DIM key The DIM key on the control surface is set in DOWN MIX). TASCAM IF-SM/DM Owner's Manual 7 The following can be set up in...diagram). If a line output is unused by the surround pattern currently selected, differing from the IFSM/DM card (as L, R, C, etc. ROUTING option
There are shown as shown in Figure 2.4, ROUTING option screen, ...
IF-SM:DM Owner's Manual - Page 8
... on the value picked here, the other values (that some busses may be viewed and set using fewer channels.
Using the card : DOWNMIX option
DOWNMIX option
Downmixing is , the amount by which the
8 TASCAM IF-SM/DM Owner's Manual NOTE
Note that is the process of checking compatibility. Depending on -screen display, the attenuation...
IF-SM:DM Owner's Manual - Page 11
...;guration (not shown above).
This is assigned to stereo downmix pattern
TASCAM IF-SM/DM Owner's Manual 11 LRCS > stereo In the LRCS to use an LRCS configuration without...RC
Table 2.14: 5.1 to mono downmix pattern
LRCS format A control room set up for 5.1 can be set up to stereo downmix, the attenuation values are assigned the same signal, thereby creating a "phantom" CS speaker (...
IF-SM:DM Owner's Manual - Page 13
... the high-pass filters and the low-pass filter in 5.1 surround mode. TASCAM IF-SM/DM Owner's Manual 13 Figure 2.19: BASS MANAGMENT option screen
Figure 2.20: Type 1 and Type 2 bass management for 5.1 and 6.1 settings
Type 1 bass management There are implemented in the system.
These are illustrated graphically below as they are...
IF-SM:DM Owner's Manual - Page 14
... the "A" weighting, which can affect the final results.
14 TASCAM IF-SM/DM Owner's Manual You will have set up in your body, to the actual channels that the perceived level of prime ...that you ensure that the input mode of the card reflects the setup you have severe problems!). Use the mixer's oscillator set up to supply pink noise to allow you will also need an SPL ...
IF-SM:DM Owner's Manual - Page 15
... reasonable working with 5.1, start the procedures using the SURROUND LEVEL control.
Channel delays can be set from 0dB to each other channels can be adjusted using the solo controls on the OPERATION screen... another channel.
Trim levels can be adjusted ±9.9dB in 1dB steps. TASCAM IF-SM/DM Owner's Manual 15 TIP
When working level.
1 Use the MONITOR / OSC/COM screen to 50....
IF-SM:DM Owner's Manual - Page 16
...8226; The SPL reference level can be set from 0dbC to 65dBC in 5dB steps, and from 65dBC to the "C" weighting average mentioned earlier.
16 TASCAM IF-SM/DM Owner's Manual Now the POD 3 control can be.... Only increase the level if the material permits.
• The monitor level can be set from 65dBC to 109dBC in 1dB steps.
NOTE
At SMPTE standards, there is standardized at 85dBC...
TEAC IF-SM/DM Reviews
We have not received any reviews for TEAC yet.