Netgear FVS114 - ProSafe VPN Firewall 8 Router Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear FVS114 manuals!
Problems with Netgear FVS114?
Ask a Question
Free Netgear FVS114 manuals!
Problems with Netgear FVS114?
Ask a Question
Most Recent Netgear FVS114 Questions
I Just Need To Get My Password So I Can Set Up My Ipad
(Posted by Boppie6742 12 years ago)
I Bought A Samsung 300v5a-a03 Lap Top And Need My Network Security Key
(Posted by gtls 12 years ago)
Popular Netgear FVS114 Manual Pages
FVS114 Reference Manual - Page 17
...site addresses and address keywords, and share high-speed cable/DSL Internet access for up to a WAN device, such as a cable modem or DSL modem.
The FVS114 is a complete security solution that rely on time-of Service attack (DoS) protection and intrusion detection. Key Features of the NETGEAR FVS114 ProSafe VPN Firewall. The FVS114 VPN Firewall provides you with four-port switch connects...
FVS114 Reference Manual - Page 19
That port then configures itself to a switch or hub.
Extensive Protocol Support
The FVS114 VPN Firewall supports the Transmission Control Protocol/Internet Protocol (TCP/IP) and Routing Information Protocol (RIP). This feature greatly simplifies configuration of PCs on your local network.
• DNS Proxy When DHCP is a protocol for the ProSafe VPN Firewall FVS114
Autosensing ...
FVS114 Reference Manual - Page 20
...your type of the FVS114 VPN Firewall:
• Flash memory for firmware upgrade.
• Free technical support seven days a week, 24 hours a day.
2-4
Introduction
202-10098-01, April 2005 For security, you can limit remote management access to a specified remote IP address or range of addresses, and you can install, configure, and operate the FVS114 ProSafe VPN Firewall within minutes after...
FVS114 Reference Manual - Page 25
...ProSafe VPN Firewall, especially this manual and the animated tutorials for configuring networking on PCs. Before proceeding with the VPN firewall router installation, familiarize yourself with your cable ISP.
• For DSL Service: You may need information such as the DSL login name/e-mail address and password in order to the Internet
3-1
202-10098-01, April 2005 Follow these instructions...
FVS114 Reference Manual - Page 29
... NETGEAR Smart Wizard Configuration Assistant welcome screen
Note: If you do so, open a browser such as the user name and password for the ProSafe VPN Firewall FVS114
With the VPN firewall router in its factory default state. Click OK. Click Done to obtain both in lower case letters.
It should be set to finish. Reference Manual for the password both IP and DNS server addresses...
FVS114 Reference Manual - Page 59
... NETGEAR VPN-enabled firewalls is configured on each endpoint with specific identification and connection information describing the other end, and vice versa. See "How to Set Up a Gateway-to-Gateway VPN Configuration" on page 5-20 to set of the tunnel to form the VPN tunnel end points.
Under these circumstances, configuring the WAN port with DHCP addressing, where the IP address of IP...
FVS114 Reference Manual - Page 60
... VPN Firewall FVS114
FQDNs supplied by Dynamic DNS providers can allow a VPN endpoint with three different, unrelated keys.
- Note: NETGEAR publishes additional interoperability scenarios with various gateway and client software products.
5-4
Basic Virtual Private Networking
202-10098-01, April 2005 MDS - 128 bits, faster but more secure.
The VPN Wizard using a dynamic IP address...
FVS114 Reference Manual - Page 67
... the ID Type menu below the check box. Select IP Address in the Protocol menu to show the Security Policy menu. Enter the public WAN IP Address of the FVS114. The resulting Connection Settings are shown in the field directly below the connection name.
Select IP Subnet in the NETGEAR ProSafe VPN Client software. In this example, type 192.168...
FVS114 Reference Manual - Page 76
... Private Networking The LAN IP address ranges of 192.168.0.x. A
FVS114 VPN Firewall
VPN Tunnel
B
FVS114 VPN Firewall
PCs
PCs
Figure 5-22: Gateway-to-Gateway VPN Tunnel
Follow the procedure below to set up the VPN tunnel using the NETGEAR default address range of each properly for the ProSafe VPN Firewall FVS114
How to Set Up a Gateway-to-Gateway VPN Configuration
Note: This section...
FVS114 Reference Manual - Page 124
... can use the reset button on page 9-7. Changing the Administrator Password
The default password for the ProSafe VPN Firewall FVS114
To restore the factory default configuration settings without knowing the login password or IP address, you change this menu. Reference Manual for the firewall's Web Configuration Manager is password. Click Apply. From the main menu of the browser interface...
FVS114 Reference Manual - Page 129
... Reference Manual for the ProSafe VPN Firewall FVS114
Note: For security, NETGEAR strongly recommends that you can register a domain name and have a specific reason to a ping from the Internet. Note: In this box unless you will not know in advance what your IP address by the firewall. How to Configure Dynamic DNS
If your firewall to Ping on Internet WAN Port
If...
FVS114 Reference Manual - Page 185
... IP Configuration window opens, which should see an entry for Local Area Connection. The window is 192.168.0.1
Configuring Windows NT4, 2000 or XP for the ProSafe VPN Firewall FVS114
1. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2. Double-click the Network and Dialup Connections icon.
3. Select Properties.
5. Install or...
FVS114 Reference Manual - Page 193
... be listed, and should match the values below if you are using the default TCP/IP settings that NETGEAR recommends for the ProSafe VPN Firewall FVS114
• The TCP/IP Properties dialog box now displays.
• Click the IP Address tab. • Select the radio button marked Obtain an IP
address from a DHCP server. • Click OK.
Repeat these steps for Windows XP...
FVS114 Reference Manual - Page 195
... the values below if you are using the default TCP/IP settings that NETGEAR recommends:
• The IP Address is between 192.168.0.2 and 192.168.0.254 • The Subnet mask is 255.255.255.0 • The Router address is configured and has rebooted, you may need to switch the "Configure" setting to a different option, then back again to the...
FVS114 Reference Manual - Page 204
... by RFC 2284.
4
Glossary
202-10098-01, April 2005 ADSL requires a special ADSL modem.
Reference Manual for the ProSafe VPN Firewall FVS114
Specifying a Default DMZ Server allows you to set up a computer or server that is available to anyone on IP addresses. An Ethernet protocol specifying how a centralized DHCP server can assign network configuration information to 198.105.232...
Netgear FVS114 Reviews
We have not received any reviews for Netgear yet.