NEC LT35 - XGA DLP Projector Support and Manuals
Get Help and Manuals for this NEC item
NEC LT35 Videos
NEC LT35 Replacing the lamp
Duration: 1:20
Total Views: 2,831
Duration: 1:20
Total Views: 2,831
NEC LT35 XGA DLP projector - $3701702
Duration: 1:13
Total Views: 7
Duration: 1:13
Total Views: 7
Popular NEC LT35 Manual Pages
NP115 : RS232 codes- Projectors - Page 34
... description
00H
00H
00H
01H
01H
00H
01H
01H
02H
03H
02H
0DH
Error contents Unknown command. Setting not possible. Specified terminal is unavailable or cannot be selected. REMOTE KEY CODE Function: This command sends remote control key codes of projector. This current model does not support this function. Power Off inhibited.
050. Command: 02H 0FH 00H 00H 02H DATA01...
LT30/LT35 spec sheet - Page 1
...a steep offset angle to physically lock down provides error free
interpolation for adaptive color tone correction to 50%. ° Lamp saver technology complete with Eco-mode™ technology that increases lamp life by up enables projector to be powered on cabinet to prevent unwanted
changes to projector settings. • Password protection restricts unauthorized use of Texas Instruments...
LT30/LT35 spec sheet - Page 2
... Control Sync Compatibility
Horizontal 15 to 100 kHz
Vertical
50 to
display properly on CD-ROM, quick start guide, product registration card
ACCESSORIES
Order Code LT30 LT35 LT30LP LT35LP ADP-CV1 LT30CM LT30ATA SCP100 PWRCRD-PJPX RGBCBL-PJPX RMT-PJ20 IRRCVR
LEATHERCASE
LEATHERROLLER
Description 4.4 pound, 2600 lumen, XGA Projector 4.4 pound, 3000 lumen, XGA Projector Replacement lamp...
WPA001 WMS100 configuration - Page 10
Setting up the WMS
Maintenance
Click to get the default user name and password if you forget it.
Only English alphanumeric characters are accepted for security control to restrict access to the WMS Receiver Box. You can press the Reset button for more than 5 seconds to upgrade firmware or reset factory default and bridge functions. Change Username/Password
Click for passwords.
7
LT30/LT35 UM - Page 3
...projectors and their electrical accessories or lamps.
Wash hands after handling. Record it is dangerous to make any part...of your NEC LT35/LT30/LT25 projector and keep the manual handy for... CABINET. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. After ...manual carefully before using your projector.
Important Information
Safety Cautions
Precautions Please read carefully to avoid problems...
LT30/LT35 UM - Page 7
...5474; Introduction to the Projector 2 ᕣ Part Names of the Projector 4
Top Features ...6 Terminal Panel Features 6 ᕤ Part Names of Contents
Important Information i
1. Installation and Connections 9
ᕡ Setting Up the Screen and the Projector 9 Selecting a Location...Table of the Remote Control 7
Battery Installation 8 Remote Control Precautions 8 Operating Range for Wireless...
LT30/LT35 UM - Page 19
... install the projector yourself. • Only use your projector on your projector cabinet or your remote control to the ground, you have adequate ventilation around your projector so heat can be injured and the projector severely damaged. • Do not use the MENU and SELECT buttons on a solid, level surface. Contact your NEC dealer for more information.
* Do not...
LT30/LT35 UM - Page 25
...projector cannot be turned off for 1 second. CAUTION:
Do not remove the lens cap by pulling on the remote control for 60 seconds after the lamp is turned off the AC power during this period.
LAMP STATUS...
LAMP STATUS POWER
Blinking
LAMP STATUS POWER
Power On
LAMP STATUS POWER
Steady orange light Blinking green Steady green
light
light
See page 50 for some time and then the projector ...
LT30/LT35 UM - Page 26
... the internal system. In this happens, replace the lamp. • If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on to cool down. • When the lamp reaches its end of the projector is set to execute the selection.
3. To select...
LT30/LT35 UM - Page 35
...turn off the AC power supply when the projector is turned off .
1. Retract adjustable tilt foot if extended. 4. Power On
LAMP STATUS POWER
Steady green light
Fan running
LAMP STATUS POWER
Standby
LAMP STATUS POWER
Blinking
Steady orange
orange light
light
About Direct Power Off
The projector has a feature called "Direct Power Off". TIP: The projector can cause loss of the power cable...
LT30/LT35 UM - Page 55
... cause an unwanted shadow and poor picture quality. • The projector will blink red and the message [The lamp has reached the end of glass may be extremely hot. Allow at 2000 (up to replace the lamp. Maintenance
» Replacing the Lamp
After your NEC dealer for replacement: • Replacement lamp LT35LP (LT35) or LT30LP (LT30/LT25) • Phillips screwdriver or equivalent...
LT30/LT35 UM - Page 58
...Lamp Indicator
Blinking light
Indicator Condition Off
Red
Steady light Red
Green
Projector Condition
Note
Normal
-
Lamp Replace the lamp. Lamp has been used beyond its end of life. Appendix
ᕡ Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector. The projector is on .
You have pressed cabinet button
when Control...
LT30/LT35 UM - Page 59
... that the power button on the projector cabinet or the remote control is on . button on the projector cabinet or the remote control. (→ page 26) • Adjust the computer image manually with the Horizontal and Vertical in [Wall Color]. After replacing the lamp, reset the lamp hours used.(→ page 45) • The lamp may fail to the notebook PC...
LT30/LT35 UM - Page 72
...The customer can 't be done by NEC Authorized Service Station, because of shortage of spare parts due to same model is not sold in the Application Sheet.
1) Repair and Return:
The 'Faulty unit' is repaired. Enduser needs to confirm the availability of the Service to NEC Authorized Service Stations.
3) Loan Only:
For this service, NEC Authorized Service Station supplies the customer with a loan...
WPA001 WMS100 users guide - Page 4
...easy to act as Sender. Presto! It's all participants, or if setup delays cause the audience to lose interest. WMS requires hardware in the ...projector or monitor for Ethernet connections.
• System Requirements • Hardware Box Requirements • Features • Installation
System Requirements
Presto! The Sender can 't be supported for the adapter, and a computer to set...
NEC LT35 Reviews
We have not received any reviews for NEC yet.