NEC LCD3000 - 30" LCD Monitor Support and Manuals
NEC LCD3000 Videos
Popular NEC LCD3000 Manual Pages
User Manual - Page 3
... to make any kind of the FCC Rules.
DO NOT REMOVE COVER (OR BACK).
Use the attached specified cables with the LCD3000 (L30HV201) color monitor so as not to interfere with the instructions, may cause harmful interference to avoid any part inside this unit has been included. This booklet is no guarantee that to CAN/CSA...
User Manual - Page 4
... PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD3000 LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. Save packaging for you are no user serviceable
parts inside of the fluorescent tube located within the LCD monitor contains mercury. • Do not bend power cord. • Do not use monitor in case of you to minimize turning...
User Manual - Page 5
... box and packing material to use with stand • Power Cord (3m) • Video Signal Cable - The following :
• LCD3000 LCD monitor with the LCD3000. To obtain the optional components and additional information, contact Customer Service at (800) 632-4662. • Macintosh Cable Adapter • External Speakers
3
Contents
Your new LCD3000™ monitor box* should contain the...
User Manual - Page 6
...monitor to the user or installer. Lay the screen face down
*Ambient temperature should be less than NEC compliant and approved, they must be used or installed without the Tabletop Stand... two ways:
1. Failure to use a trained, NEC authorized service person. NEC strongly recommends using a cord or chain which is strongly recommended to follow NEC standard mounting procedures could result in...
User Manual - Page 11
... power before making connections.
• Refer to your equipment user manual.
4. Place monitor on both sides of monitor to remove the stand 1. Please turn off . 2. CAUTION MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE. To install or replace batteries: 1. NEC recommends the following battery use the Remote Control for a long period, remove the batteries...
User Manual - Page 14
... call NEC-Mitsubishi Electronics Display of America, Inc. For connection, select AUDIO 1, 2 or 3 from the AUDIO INPUT button. For older Macintosh® computers, use Macintosh cable adapter to connect to your Macintosh's owner's manual for more information about your computer's video output requirements and any special identification or configuring your monitor's image and monitor may...
User Manual - Page 16
... 3] from the OUT connector that has been set here. • When connecting one or more information.
• Video signals can be both used for more LCD monitors, use the VIDEO OUT connectors (BNC). • The... AUDIO IN 2 and 3 can be connected to display your VCR or laser disc player owner's manual for ...
User Manual - Page 17
... player owner's manual for audio input. Some DVD players may have different connectors, such as Cr/Pr, Y and Cb/Pb.
Select [DVD/HD] input mode from the AUDIO INPUT button. When connecting one or more information. • To connect the RGB 3 DVD/HD In connector (BNC) on the LCD monitor, use the RGB...
User Manual - Page 18
... AUDIO OUT connector (RCA) on the LCD monitor and the audio input on the amplifier. • Do not reverse the audio left input
To audio right input
External speaker
External speaker
16 Connections -continued
Connecting to a Stereo Amplifier
You can connect your LCD monitor. Refer to your amplifier owner's manual for the AUDIO IN 3 only.
User Manual - Page 24
... EXIT:PRE MENU:END
LONG CABLE MANUAL
R DELAY
0
G DELAY
0
B DELAY
0
R SHARPNESS 0
G SHARPNESS 0
B SHARPNESS 0
SOG PEAK
0
:SEL EXIT:PRE MENU:END
PICTURE SCREEN AUDIO PICTURE IN PICTURE CONFIGURATION 1 CONFIGURATION 2
:SEL EXIT:PRE SET:NEXT MENU:END
A set up ON/OFF of long cable alteration can preset the monitor to 30 seconds is available. Please refer to...
User Manual - Page 32
...optimizing display performance. AccuColor® Control System with a 1-year onsite warranty (including backlight) and 24/7 customer service and technical support. Multiple Frequency Technology automatically adjusts monitor to optimal settings upon initial setup.
CableComp™ automatic long cable compensation prevents image quality degradation caused by the Digital Display Working Group...
User Manual - Page 33
... to increase or decrease the clock total. • Check to make sure that a supported mode has been selected on the display card or system being used . (Please consult display card or
system manual to change graphics mode.) • Check the monitor and your text is garbled, change graphics mode.)
Selected resolution is not displayed...
User Manual - Page 34
...NEC-Mitsubishi Monitor Customer Service & Support
Customer Service and Technical Support: Fax:
Parts and Accessories/Macintosh Cable Adapter:
Customer Service Policies & Processes:
Online Technical Support Knowledge Base:
Customer Service & Technical Support Email:
(800) 632-4662 (800) 695-3044
(888) NEC...Status Information
NEC Rebate Status ...nec-mitsubishi.com
Windows® 95/98/Me/2000/...
User Manual - Page 35
...manual, Power Cord, Video Signal Cable, Remote Control, AA Battery x 2, Clamper x 2, Screw x 2, CD-ROM
33 Specifications
LCD Module
Pixel Pitch
Resolution
Color
Brightness
Viewing Angle
External speaker...Resolutions Supported
...x 449 (H )x 114 (D) mm (without Stand), 706 (W) x 489 (H) x 200 (D) mm (with Stand)
840 (W) x 640 (H) x 360 ...NEC-Mitsubishi Electronics Display cites recommended resolution
1280 x...
User Manual - Page 36
... such service, the serial number of America at NMD-A's sole option) any part of the enclosed unit which proves defective for a period of one (1) year from the date of third party components is not covered under this warranty. Replacement parts or unit may vary. In order to the instructions contained in accordance with many systems, specific...
NEC LCD3000 Reviews
Do you have an experience with the NEC LCD3000 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!