NEC E1100 - MultiSync Plus - 21" CRT Display Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC E1100 Manual Pages
User Manual - Page 3
...JC-2147UMA color monitor so as not to interfere
with radio and television reception. (1) Please use the supplied power cable or equivalent to make any kind of the FCC Rules. These limits are designed to avoid any part...REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Therefore, it is in a residential installation. Use of other cables and adapters may cause harmful interference to part 15...
User Manual - Page 4
Contents
Your new NEC Technologies MultiSync® E1100+™ monitor box* should contain the following:
• MultiSync E1100+ (JC-2147UMA) Monitor with tilt/swivel base • Power Cord • Captive Signal Cable • Macintosh Cable Adapter • User's Manual • Registration Card
Power Cord Macintosh Cable Adapter
Captive Signal Cable
NEC Enterprise Series
EM1u10lt0iS+...
User Manual - Page 5
... the computer (Figure B.1). NOTE: If you have any problems, please refer to the Troubleshooting section of the captive signal cable to the power outlet (Figure C.1).
6. Attach the 15-pin mini D-SUB end of this User's Manual.
5. Connect one end of the power cord to the MultiSync E1100+ monitor and the other end to the Macintosh cable...
User Manual - Page 7
...or increase the adjustment. Down/Up: Moves the image vertically (up /down to the factory setting. Short/Tall: Decreases or increases the vertical size of the menu.
Only executes control or enters...the controls. Controls
OSM™ (On-Screen Manager) control buttons on the front of the monitor function
as the screen is displayed in a sub-menu, it indicates further choices are displayed ...
User Manual - Page 8
... Blue: NEC's AccuColor Control System decreases or increases the monitor's red,...AccuColor® Control System
Color presets 1 through 5 selects the desired color setting. Sides Tilt (parallelogram): Decreases or increases the tilt of the screen to ...change in others.
The best way to determine the vertical linearity is replaced by using a drawing application that a one-inch circle is a ...
User Manual - Page 9
... graphics boards, keep the factory setting at ENABLE. Monitor Info: Indicates the model and serial numbers of the signal being applied to activate OSM controls while in seven languages. When attempting to the monitor by highlighting the control to your monitor.
78133724.wpc
7
9
11/18/98, 11:52 AM Note: NEC recommends that you a reset most...
User Manual - Page 10
... with care when transporting. The monitor should be installed close to the monitor. • Keep the monitor away from the power supply. Recommended Use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC® E1100+™ COLOR MONITOR:
• DO NOT OPEN THE MONITOR. Do not block ventilated openings...
User Manual - Page 11
... typing. • Get regular eye checkups. Blink often.
• Position the monitor at a 90° angle to windows and other light sources to insufficient contrast For more detailed information on setting up a healthy work environment, call NEC at (800) 820-1230, NEC FastFacts™ information at most of the time (the screen or reference...
User Manual - Page 12
... Colors
Depends on horizontal and vertical frequencies only
Active Display Area (Factory Setting) Active Display Area (Full Scan) Power Supply Current Rating Dimensions
Horizontal: Vertical:
Weight
Environmental Considerations Operating Temperature: Humidity: Feet: Storage Temperature: Humidity: Feet:
MultiSync® E1100+™ Monitor
Notes
53 cm/21 inch 50.2 cm/19.8 inch 1730 mm
90...
User Manual - Page 13
...Copyright 1998 by allowing the monitor to send its capabilities (such as screen size and resolutions supported) directly to a lower...with the Windows®95/98 operating system facilitates setup and installation by NEC Technologies, Inc.
78133724.wpc
11
13
11/18/...-Screen Manager) Controls: Allow you to change between five color settings on -screen menus. Plug and Play: The Microsoft® ...
User Manual - Page 14
... electrical devices that may be causing electrical interference away from the monitor.
• See inside cover of User's Manual for proper connection or make sure the display card is Macintosh ...computer. • Check pin assignments and signal timings of 20 minutes should be connected.
Troubleshooting
No picture • Display card should be completely seated in its slot. • ...
User Manual - Page 15
... 95/98 INF File: http://www.nec.com/drivers/graphic.htm
Then download the file NECMSINF.ZIP
• FastFacts™ Information (800) 366-0476
INFORMATION
DESCRIPTION
DOCUMENT #
MultiSync® E1100+™ monitor
Detailed monitor information
214701
Glossary
Definition of terms related to functions, features and installation of the MultiSync monitor
900203
More Information
Names and...
User Manual - Page 16
... or operated contrary to the instructions contained in the User's Manual. No warranty service is provided outside of the ...set forth below, agrees to repair or replace (at 1-800-632-4662.
14
78133724.wpc
16
11/18/98, 11:52 AM This warranty only covers Product distribution in accordance with many systems, specific functional implementation by NECTECH.
This warranty gives you specific...
User Manual - Page 17
...The energy requirements include a demand that are often left running continuously.
The main problem, as far as a joint effort by the TCO (The Swedish Confederation of ... been possible for the majority of electronics equipment to another group of goods and services to conserve energy. Environmental Requirements
Brominated flame retardants Brominated flame retardants are related to...
User Manual - Page 56
... granted to others.
in accordance with Part 15 of NEC Home Electronics, Ltd. The ENERGY STAR emblem does not represent EPA endorsement of Product:
Computer Monitor
Equipment Classification: Class B Peripheral
Models:
JC-2147UMA
We hereby declare that this product meets the ENERGY STAR guidelines for design and specification improvements, the information in the U.S. Operation...
NEC E1100 Reviews
We have not received any reviews for NEC yet.