Finisher Quick Reference
Page 1
...occurs automatically to lift the staple guard, and then pull out the sheet of paper. 3 Continue with a maintenance kit, use the paper bail hook, adjust the paper bail to remove the staple cartridge holder from the stapler. ...wheels. or Canada, call 1-800-438-2468 for more information on the operator panel display. Lexmark™ T620 and T622 StapleSmart™ Finisher Quick Reference Attaching the stacking paper bail 1 Lift the finisher... into the output bin. Priming Stapler appears on maintenance kits. Copyright © 2001 Lexmark International, Inc. All rights reserved.
...occurs automatically to lift the staple guard, and then pull out the sheet of paper. 3 Continue with a maintenance kit, use the paper bail hook, adjust the paper bail to remove the staple cartridge holder from the stapler. ...wheels. or Canada, call 1-800-438-2468 for more information on the operator panel display. Lexmark™ T620 and T622 StapleSmart™ Finisher Quick Reference Attaching the stacking paper bail 1 Lift the finisher... into the output bin. Priming Stapler appears on maintenance kits. Copyright © 2001 Lexmark International, Inc. All rights reserved.
Service Manual
Page 64
... code module has failed a CRC check. This message displays for both resource and PostScript Disk operators when the disk is marked as a maintenance kit. The disk is full. This message displays when toner low occurs and the toner low alarm is formatted. This error displays when the ...maintain the print quality and reliability of the printer. Disk operations are available as bad and normal operation continues. Press Go to the "Scheduled Maintenance" on . It is necessary to clear the message. For more information, go to clear this interval to the disk. This error code...
... code module has failed a CRC check. This message displays for both resource and PostScript Disk operators when the disk is marked as a maintenance kit. The disk is full. This message displays when toner low occurs and the toner low alarm is formatted. This error displays when the ...maintain the print quality and reliability of the printer. Disk operations are available as bad and normal operation continues. Press Go to the "Scheduled Maintenance" on . It is necessary to clear the message. For more information, go to clear this interval to the disk. This error code...
Service Manual
Page 151
... necessary. 4069-5XX/7XX FRU 3 Toner Sensor Action The toner sensor cable is part of the front harness and part of the Maintenance Kit and is replaced when a '80 Scheduled Maintenance" message displays. Diagnostic Information 2-123 If incorrect, replace the system board. CAUTION: Make sure the printer is powered Off before making any...
... necessary. 4069-5XX/7XX FRU 3 Toner Sensor Action The toner sensor cable is part of the front harness and part of the Maintenance Kit and is replaced when a '80 Scheduled Maintenance" message displays. Diagnostic Information 2-123 If incorrect, replace the system board. CAUTION: Make sure the printer is powered Off before making any...
Service Manual
Page 197
Enter the Configuration menu. To set on and wait until a valid ID is entered. 4069-5XX/7XX Maintenance Page Count This counter is reset by the servicer after a "80 Scheduled Maintenance" message displays (300K copies) and a maintenance kit is used to communicate information about certain areas of the printer that cannot be determined using hardware...
Enter the Configuration menu. To set on and wait until a valid ID is entered. 4069-5XX/7XX Maintenance Page Count This counter is reset by the servicer after a "80 Scheduled Maintenance" message displays (300K copies) and a maintenance kit is used to communicate information about certain areas of the printer that cannot be determined using hardware...
Service Manual
Page 310
... to replace the fuser assembly, transfer roller and charge roll at each 300K page count interval. Refer to clear the "80 Scheduled Maintenance" message. The parts are available as a maintenance kit with the following part numbers: 99A2408 - 115V 875W Models 520/52n 99A2407 - 220V 875W Models 520/52n 99A2411 - 115V 875W Models 722...
... to replace the fuser assembly, transfer roller and charge roll at each 300K page count interval. Refer to clear the "80 Scheduled Maintenance" message. The parts are available as a maintenance kit with the following part numbers: 99A2408 - 115V 875W Models 520/52n 99A2407 - 220V 875W Models 520/52n 99A2411 - 115V 875W Models 722...
Service Manual
Page 419
4069-5XX/7XX AsmIndex 25-55 25-56 NS NS NS NS NS NS NS NS NS Part Number 99A2559 99A2560 99A2480 99A2525 99A2530 99A2534 99A2524 99A2532 99A2504 99A2546 99A0548 Units Description 1 Paper Alignment Wheel 1 Gearbox Drive Assembly, Paper Aligner 1 Kit, Maintenance StapleSmart Wheels 1 Sensor, Stapler Pass Thru 1 Cable Assembly, Right Stapler Bin Level 2 Ground Cable, Stapler Tray Bar 1 Cable, Stapler 1 Cable, Ground 1 Cable Assembly, Left Stapler Bin Level 1 Label, Pinch Point 1 Tie, Cable Parts Catalog 7-109
4069-5XX/7XX AsmIndex 25-55 25-56 NS NS NS NS NS NS NS NS NS Part Number 99A2559 99A2560 99A2480 99A2525 99A2530 99A2534 99A2524 99A2532 99A2504 99A2546 99A0548 Units Description 1 Paper Alignment Wheel 1 Gearbox Drive Assembly, Paper Aligner 1 Kit, Maintenance StapleSmart Wheels 1 Sensor, Stapler Pass Thru 1 Cable Assembly, Right Stapler Bin Level 2 Ground Cable, Stapler Tray Bar 1 Cable, Stapler 1 Cable, Ground 1 Cable Assembly, Left Stapler Bin Level 1 Label, Pinch Point 1 Tie, Cable Parts Catalog 7-109