Lexmark 43J2600 - Optra S 1625 B/W Laser Printer Support and Manuals
Get Help and Manuals for this Lexmark item
This item is in your list!
View All Support Options Below
Free Lexmark 43J2600 manuals!
Problems with Lexmark 43J2600?
Ask a Question
Free Lexmark 43J2600 manuals!
Problems with Lexmark 43J2600?
Ask a Question
Popular Lexmark 43J2600 Manual Pages
Service Manual - Page 33
... communications to allow the servicer a method of engine code existing in Slot 2. The specific error is installed in Network Card x. 977 - Download Emulation CRC Failure. Replace Network Card x. 979 - Flash parts failed while programming Network Card x.
980 Comm
The engine is Bad. 4059-XXX
Error Code
Action
956 Configuration ID
Indicates a problem with it. 978 - The...
Service Manual - Page 44
... cartridge is supported. It may be read the cartridge ID, but the ID did not pass the verification test. Depending on a model 3455 printer if the smart cartridge or smart cartridge hardware is detected. Try another model 3455 print cartridge. It may be allowed to print pages during this does not fix the problem, go to "Smart Cartridge Service Check" on the setting...
Service Manual - Page 104
.... Note: The Quick Disk Test is unusable. Network Card Option
Error Code 976 - Error Code 977 - Network Card X (X=Network card 1, 2, or 3)
A 976 error code indicates an unrecoverable software error in another slot, replace the interconnect board.
2-77 4059 Service Manual
If you are correctly installed.
This test is correctly installed in slot x on the disk size.
Service Manual - Page 111
...replace the control board. The voltage measures approximately 0 V dc. If this does not fix the problem, replace... the control board.
271 Paper Jam - Output Bin X is correctly connected to clear the message. If correct, check the voltage at J3-3.
Check Bin X. Disconnect the pass thru sensor cable from the sensor cable, If incorrect, repair..., replace the sensor assembly.
...
Service Manual - Page 116
If the test indicates that a problem is installed in the HYSNC signal to the printhead. Printhead Service Check
The printhead assembly does not contain any service replaceable parts or components. The voltage at J8-4 measures approximately +5 V dc. If correct, replace the printhead assembly.
2-89 4059 Service Manual 4059-XXX
Parallel Port Service Check
Run the "Parallel Wrap Test" on ...
Service Manual - Page 117
... to J3 on the engine board. 4059-XXX
Service Error Code
2 Error Code 934 Mirror Motor Lost Lock Error Code 935 Mirror Motor unable to reach operating speed
Explanation
These error codes indicate a problem with the mirror motor circuit in the following order:
engine board
printhead assembly
Diagnostic Information 2-90 If incorrect, replace the cable. Check the continuity of the mirror...
Service Manual - Page 118
...• Install another print cartridge if available before proceeding with the controller board removed while running the print test.
2-91 4059 Service Manual
All voltages measured during the print cycle are measured with
the service checks.
• Use Tray 1 to test for the installed software can return the printer to the original customer printer setup.
• Print Resolution: Set to...
Service Manual - Page 129
... loose toner around the area of printed page
Service Tip: This is being carried through the printer on backside of the transfer plate assembly. If the problem continues, replace the FRUs in the following order:
HVPS
engine board
Smart Cartridge Service Check
Note: If you are unable to troubleshoot the printer.
4059-XXX Print Quality - Toner on the...
Service Manual - Page 132
... to the roll, oil or other contaminants on the toner sensor results in a 929 service error. Check the voltage at J10-12. Any print quality problems such as necessary.
2-105 4059 Service Manual Service Tip: The transfer roll assembly is part of the Maintenance Kit for models 2450, 2455 and 3455 printers and is 17.0 mm (.669 inch) diameter.
Service Manual - Page 153
... servicer after a "80 Scheduled Maintenance" message displays (250K copies) and a maintenance kit is complete, the menu returns to the Printer Setup Reset Maintenance Count screen. Select Maintenance Count Value from the Printer Setup menu. - Pressing Select causes the maintenance page counter to reset to zero:
1. When the reset operation is installed. The Configuration ID is originally set...
Service Manual - Page 160
... have a system board.
Fuser Operation
The fuser in the Optra S printers is made when the option is installed below the printer.
There are "Smart Options" or options that controls the option mechanism.
The thermistor assembly is designed to keep the temperature of
3-27 4059 Service Manual The paper input sensor is located in the level 2 duplex...
Service Manual - Page 164
...parts, follow the instructions below in addition to all ESD-sensitive parts in a grounded metal
cabinet (case).
• Be extra careful in your wrist. weather heating is used because low humidity increases static electricity.
4-1 4059 Service Manual Repair...sensitive part by
other personnel. If you are removing a pluggable module, use parts that are electrical grounds. Install machine...
Service Manual - Page 251
...This chapter describes procedures for printer preventive maintenance. If any non-Lexmark attachments
Lubrication Specifications
Lubricate only when parts are replaced or as needed, not... can help prevent problems and maintain optimum performance. Some unauthorized lubricants may chemically attack polycarbonate parts. Safety Inspection Guide
The purpose of this inspection guide is to lubricate...
Service Manual - Page 259
...
4
Pad, Machine Mounting
1
Transfer Plate Assembly
1
Transfer Plate Assembly 3455
1
Plate Assembly, Stacker Ground
2450/2455/3455
1
Support, Right Stacker
1250/1255/1620/1650/2420/1855/1625
1
Right Sideframe
1
Track, Cartridge Guide RH
1
Fan, Auxiliary 2420/2450/3455
1
Contact Kit PP 99A0585
3
o Contact, Doctor Blade/TAR/Developer Roll
1
o Contact, PC Drum
1
o Contact...
Parts List - Page 9
...
4
Pad, Machine Mounting
1
Transfer Plate Assembly
1
Transfer Plate Assembly 3455
1
Plate Assembly, Stacker Ground
2450/2455/3455
1
Support, Right Stacker
1250/1255/1620/1650/2420/1855/1625
1
Right Sideframe
1
Track, Cartridge Guide RH
1
Fan, Auxiliary 2420/2450/3455
1
Contact Kit PP 99A0585
3
o Contact, Doctor Blade/TAR/Developer Roll
1
o Contact, PC Drum
1
o Contact...
Lexmark 43J2600 Reviews
Do you have an experience with the Lexmark 43J2600 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Lexmark yet.
Earn 750 points for your review!