JET Tools JWL-1015 Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools JWL-1015 manuals!
Problems with JET Tools JWL-1015?
Ask a Question
Free JET Tools JWL-1015 manuals!
Problems with JET Tools JWL-1015?
Ask a Question
Popular JET Tools JWL-1015 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
10x15-inch Woodworking Lathe
Models JWL-1015, JWL-1015VS
model JWL-1015VS shown
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-719100 Revision A1 02/2014 Copyright © 2014 JET
User Manual - Page 3
... 16.2.1 JWL-1015VS Lathe - 2.0 Table of contents
Section
Page
1.0 Warranty and Service...2 2.0 Table of workpiece 21 14.0 Troubleshooting the JWL-1015/1015VS Lathes 21 15.0 Optional accessories ...22 16.0 Replacement Parts...23 16.1.1 JWL-1015 Lathe - JWL-1015/1015VS lathes 8 7.0 Setup and assembly...9
7.1 Shipping contents...9 7.2 Mounting lathe to stand/table ...9 7.3 Installing/removing...
User Manual - Page 5
... expose them to provide years of this manual for a JET Model JWL-1015 and JWL-1015VS Lathe. 25. Start at low speed and allow the Lathe to ramp up a workpiece, always use power tools in this document. This manual is provided by hand to a spinning workpiece.
34. Read and understand the entire contents of trouble-free operation if used in accordance...
User Manual - Page 6
... 19. Spindle pulley 7. Tailstock quill lock handle 11. Spur center 8. On/Off switch with safety key 16. Warning label 23. JWL-1015/1015VS lathes
Figure 1: Variable speed model shown
1. Index pin 4. Belt tension handle 22. Knockout rod
6 5.0 Features and nomenclature - Speed chart 5. Tool Rest 9. Live center 14. Controller assembly 18. DC motor 21.
User Manual - Page 7
Power plug installed yes yes Recommended circuit size1 10A 10A
1 subject to change specifications at time of publication, but because of our policy of continuous improvement, JET reserves the right to local/national electrical codes. 6.0 Specifications
Model number JWL-1015 JWL-1015VS Stock number 719100 719110
Motor and electricals: Motor type .....induction, totally enclosed fan ...
User Manual - Page 8
JWL-1015/1015VS lathes
Figure 2 Clearance hole spacing for mounting lathe
8 6.1 Hole pattern -
User Manual - Page 9
... pad, and do
not need to remove faceplate to install spur center. Drive spur center into spindle.
A 1 Spur center - Push spur center into workpiece (see Figure 3)
1 Lathe 1 Live center - Missing parts, if any shipping material until the Lathe is assembled and running properly. Read the instruction manual thoroughly for assembly:
3/16" hex key ("Allen" wrench)
Exposed...
User Manual - Page 10
... conductor. Push live center
Refer to Figure 7. Figure 7
8.0 Electrical connections
The JWL-1015/JWL-1015VS JET lathe is properly grounded. Local codes take precedence over recommendations.
8.1 Grounding instructions
1. This tool is equipped with an electric cord having an outer surface that is properly installed and grounded in accordance with the workpiece and is intended for use on...
User Manual - Page 12
... any of six pulley sets, according to inside of three pulley sets.
Adjust cam lock nut (Figure 11) as needed. Figure 14
2.
Make sure belt is properly seated in position, remove tailstock from bed, and turn it over. Figure 12: variable speed chart
9.3.2 Step Pulley Model
The JWL-1015 step pulley lathe has three speed ranges...
User Manual - Page 21
... 3000 1600 1080 810 650
Table 2
Finishing RPM 3000 2480 1650 1240 1000
14.0 Troubleshooting the JWL-1015/1015VS Lathes
Table 3
Trouble
Probable Cause
Remedy
Motor fails to develop full power
Motor or spindle stalls or will not start
Excessive vibration
Tools tend to grab or dig in
Tailstock moves when applying pressure Red LED light...
User Manual - Page 22
Bed Extension (21") for JWL-1015/1015VS Lathes
# 719103 - Stand for JWL-1015/1015VS Lathes
# 719102 - Stand Extension for JWL-1015/1015VS Lathes 22 Contact your lathe. 15.0 Optional accessories
These accessory items, purchased separately, can enhance the functionality of your dealer to order, or call JET at the phone number on the cover. # 719101 -
User Manual - Page 23
...
23 Having the Model Number and Serial Number of your machine available when you call 1800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). To order parts or reach our service department, call will allow us to serve you quickly and accurately.
16.1.1 JWL-1015 Lathe - 16.0 Replacement Parts
Replacement parts are listed on...
User Manual - Page 24
....1.2 JWL-1015 Lathe - Rubber Cover 1 36 JWL1015-136 Bushing...1 37 JWL1015-137 Lock Handle Assembly, Motor Plate 1 38 JWL1015-138 Motor Label...1 39 JWL1015-139 Motor 1/2HP, 1Ph, 115V ......... 1 JML-35-1 Capacitor (not shown 25μf,250 VAC 1 JML-35-2 Capacitor Cover (not shown 1 JML-35-3 Motor Fan Cover (not shown 1 JWL1015-TBA........... Handwheel...1 15 TS-0267021 Set...
User Manual - Page 27
... List
Index No Part No
Description
Size
Qty
JWL1015VS-HA ........ Handwheel...1 15 TS-0267021 Set Screw 1/4"-20x1/4 4 16 BB-6004VV Ball Bearing 6204VV 1 17 JWL1015VS-117....... I.D Label ...1 27 TS-0267041 Socket Set Screw 1/4"-20x3/8 2 28 JET-92 JET Logo with Cap (not shown 2 JWL1015VS-MFC ..... Rubber Cover 1 36 JWL1015-136 Bushing...1 37 JWL1015-137 Lock Handle...
JET Tools JWL-1015 Reviews
Do you have an experience with the JET Tools JWL-1015 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!