JET Tools HVBS-56M Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools HVBS-56M manuals!
Problems with JET Tools HVBS-56M?
Ask a Question
Free JET Tools HVBS-56M manuals!
Problems with JET Tools HVBS-56M?
Ask a Question
Popular JET Tools HVBS-56M Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Horizontal/Vertical Bandsaw
Model: HVBS-56M
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-414458 Revision G3 02/2014 Copyright © 2014 JET
User Manual - Page 2
..., abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of JPW Industries, Inc.
Pro-Duty Air Tools 2 Year - JET Parallel clamps; VOLT Series Electric Hoists; This warranty does not cover failures due directly or indirectly to Get Technical Support Please contact Technical Service by a 90 day limited warranty against manufacturers' defects...
User Manual - Page 3
... Speed...12 Adjusting Blade Guides ...12 Adjusting Blade Tension ...12 Changing Blades ...13 Adjusting Blade Guide Bearings...13 Adjusting Blade Tracking ...14 Adjusting Feed Pressure...14 Blade-Table Squareness ...14 Adjusting Automatic Shut-Off ...15 Adjusting the Vise...15 Lubrication...15 Breakdown for Bow Assembly ...17 Parts List for the HVBS-56M Bandsaw 19 Wiring Diagram...
User Manual - Page 4
...of blade tension, blade guides, and thrust bearing....instruction manual before operating saw." Don't use the next heavier gage. Nonslip footwear is designed and intended for lubricating and changing accessories.
15. If in double, use power tools in moving parts. It is in working order.
2. Remove adjusting keys and wrenches. This bandsaw is recommended. When using this bandsaw...
User Manual - Page 5
...repaired or replaced.
21. do this machine while tired or under the influence of parts, mounting and any medication.
25. Before further use your work with approved safety equipment, such as face or dust masks that are specifically....
24. Some examples of the blade or cutter.
22. Don't leave tool until it comes to filter out microscopic particles.
20. Looking around, carrying on...
User Manual - Page 6
... like the plug illustrated in accordance with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in sketch D. Repair or replace a damaged or worn cord immediately. The tool has a grounding that is the equipment-grounding conductor. Make sure the tool is necessary, do not connect the equipment-grounding conductor to...
User Manual - Page 7
Specifications Model Number...HVBS-56M Stock Number...414458 Horizontal Capacity:
Round @ 90°...5" Round @ 45°...3" Rectangle @ 90 5"(H) x 5-3/4"(W), and ....)...115 lbs. The specifications in this manual are given as general information and are not binding. JET reserves the right to effect, at any reason whatsoever.
7
The conversion from 115V to parts, fittings, and accessory...
User Manual - Page 8
...Note: Read and understand the entire manual before attempting setup or operation.
1. Remove the brace (C, Fig. 1)...Tools Required for other leg.
4. Attach a leg to the motor side of the bed and bow using four 5/16"x3/4" carriage bolts, four 5/16" flat washers and four 5/16" hex nuts. Repeat for Assembly
• #2 Cross Point Screwdriver • 6-8" Adjustable Wrench or Wrench Set...
User Manual - Page 10
... the saw from the power source before making any repairs or adjustments. Slide pulley cover (A, Fig. 5) around motor shaft and worm gear shaft. Close pulley cover. Make sure set screw (B, Fig. 6). Vertical Cutting Plate Assembly
Note: These steps are only necessary when using the bandsaw in place.
17. Slide handwheel (E, Fig. 6) onto shaft...
User Manual - Page 11
... switch to 230V operation, follow the wiring diagram found on the end will have to be securely fastened to the cover plate screw. This bandsaw is designed for use on a circuit with two screws (B, Fig. 8).
6. Before hooking up to a two pole receptacle (D, Fig. 9) if a properly grounded outlet is rated at 230V. The HVBS-56M...
User Manual - Page 14
... arm to wheel flange. Confirm that blade tension is set at the factory and should ever require adjustment:
1. Loosen bolts (A, Fig. 15).
8. Turn set screw clockwise to track closer to the vertical position and... by removing the knob found on the top side of proper feed pressure is set properly. Adjusting Feed Pressure
1. The tracking is in place with the back cover open. Failure...
User Manual - Page 15
... shop items, as possible to aid in your manual. After making this type of inspection; This setting should lie flat against the blade and vise, so that you can be sure to ensure a straight cut .
3. Place a square on each blade guide assembly and rotate the blade guide assembly until there is correct. Adjust the...
User Manual - Page 19
... Socket Set Screw 5/16"x5/16 4 21........ HVBS462-022 Wire Relief Retainer 2 25........ HVBS56M-029-1 Plastic Cover 1 30........ HVBS462-030 E-Ring E10 1 31........ HVBS462-040 Electric Cord Clip 1 42........ TS-0081031 Hex Cap Bolt 5/16"x3/4 6
19 Parts List for the HVBS-56M Bandsaw
Index Part No. HVBS462-015 Adjusting Rod 1 16........ HVBS462-018 Support Plate...
User Manual - Page 20
...0680031 Flat Washer 5/16 3 52........ HVBS56M-057 Adjustable Bracket LH 1 57A ...HVBS56M-066 Lock Knob 1 67........ TS-...HVBS56M-057A Adjustable Bracket Assembly LH 1 58........ HVBS462-062 Guide Pivot 2 62A ..... HVBS462-062-1 Centrifugal Guide...x3/4 6 51........ HVBS462-076 Switch Cut Off Trip 1 77........ ...Washer 5/16 2 79........ HVBS56M-380 Blade Back Safety Cover...
User Manual - Page 21
... 116...... HVBS462-132A Blade Guard-Left 1 156...... Index Part No. HVBS463-170 Wire Plug 3 117...... HVBS462-156 Round... Plate Draw Block 1 107...... HVBS462-109 Blade Tension Sliding Guide 2 110...... VB-A22 V-Belt A22 1 113...... 414301 Blade... shown 1 HVBS56M-WL Warning Label (not shown 1 JM-56M Stripe Decal (not shown 1
21 TS-0270051 Socket Set Screw 5/16...
JET Tools HVBS-56M Reviews
We have not received any reviews for JET Tools yet.