JET Tools BD-920W Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools BD-920W manuals!
Problems with JET Tools BD-920W?
Ask a Question
Free JET Tools BD-920W manuals!
Problems with JET Tools BD-920W?
Ask a Question
Popular JET Tools BD-920W Manual Pages
User Manual - Page 1
M-321376 Revision H 01/2013 Copyright © 2013 Walter Meier (Manufacturing) Inc. This .pdf document is bookmarked
Operating Instructions and Parts Manual
9 x 20-inch Belt Drive Bench Lathe
Model BD-920W
WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com
Part No.
User Manual - Page 2
...-274-6848. You must provide proof of initial purchase date and an explanation of these Walter Meier Authorized Service Centers can give you specific legal rights; If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price, at your local Walter Meier distributor, or visit www.jettools.com...
User Manual - Page 3
... View 44 Lathe Bed Assembly - Parts List...45 Wiring Diagram ...46
3 Parts List 37 Top Slide Assembly - Table of Contents
Warranty and Service...2 Table of Contents ...3 Introduction ...7 Specifications ...7 Unpacking ...8
Contents of the Shipping Container ...8 Set Up and Preparation for Operation...9 General Description ...9 Controls ...12 Operation ...13
Tool Set-Up...13 Manual Turning...
User Manual - Page 4
... conductor.
4 Use only 3-wire extension cords that have the proper outlet installed by qualified service personnel; Repair or replace damaged or worn cord immediately.
2. The tool has a grounding plug that looks like the adapter illustrated in accordance with all local codes and ordinances. If the tool must be reconnected for use on a supply circuit having an outer...
User Manual - Page 5
.... ALWAYS USE SAFETY GLASSES. MAINTAIN TOOLS WITH CARE. when changing accessories, such as blades, bits, cutters, and the like.
20. B. Replace the warning labels if they are removed from work undivided attention. If you are careless acts that use this manual. Do not use .
5. Form habit of a lathe, do a job for which may get...
User Manual - Page 6
... product will operate properly and perform its operation. USE RECOMMENDED ACCESSORIES. Serious injury could occur if the tool is tipped or if the cutting tool is damaged should be properly repaired or replaced.
24. A guard or other part that is in feet
120V
25 ft.
50ft.
100ft. 150ft. Some dust created by power sanding, sawing...
User Manual - Page 7
...manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to change specifications at our web site: www.waltermeier.com. Specifications
Model Number...BD-920W...to provide years of trouble free operation if used in accordance with instructions set forth in Spindle ...
User Manual - Page 8
...12/14mm (Z)
Figure 1
* parts marked with the following parts list to the threaded spindle. Missing parts, if any shipping material until the Lathe is assembled and running properly.
Unpacking
Open shipping container and check for assembly, maintenance and safety instructions. Contents of this manual before attempting set screw on the spindle. When installing either the jaw chuck...
User Manual - Page 9
Set Up and Preparation for alignment. Local codes take precedence over recommendations. By combining high cheeks with four screws and uses four adjusting screws for Operation
To avoid twisting the bed, make sure the location to which the lathe... the BD920W Lathe be ... 5. General Description
Lathe Bed
The Lathe bed is bolted...Carefully read the grounding instructions on the idler (Figure 4)....
User Manual - Page 13
...less. When turning, the tool has a tendency to bend under the tool (Figure 13). For best results, tool overhang should be obtained by comparing the tool point with the point of the work piece.
Manual Turning
Apron travel, cross... then move lever (A, Figure 15) to engage feed. Operation
Tool Set-Up
The cutting angle is correct when the cutting edge is in the tailstock. The correct height...
User Manual - Page 16
... Drill Chuck (Optional)
Use the drill chuck to ensure accurate clamping and long service life.
Lathe Accessories
Three Jaw Universal Lathe Chuck
Using this universal chuck (Figure 22), round, triangular, square, hexagonal, ... (Figure 24). These permit the holding of asymmetrical pieces and enable the accurate set-up of 600 RPM. Its use is necessary to hold centering drills and twist...
User Manual - Page 17
... drilling tool, and therefore, must be filed or remilled. The place of the workpiece under pressure from the machine. Tighten three nuts (1, Figure 27). Set the fingers snug to the workpiece but not tight against the workpiece.
Loosen three hex nuts (1, Figure 27).
2. Steady Rest
The steady rest (Figure 26) serves as a support...
User Manual - Page 18
... spindle should still revolve freely.
They can be adjusted.
Adjustment and Replacement
Adjustment of the spindle. Caution: excessive tightening or preloading will damage the...with a gib strip and can be combined for tools to be clamped. Re-tighten set screw (1, Figure 32). Figure 29 Figure 30
...installing a cutting tool. Adjustment of the four tools into position (Figure 29).
User Manual - Page 23
Description
Size
Qty
1 BD920N-1002 ..........Headstock Casting 1 2 1003 Cover ...2 3 32007 Ball Bearing 2 4 1005 Gasket ...2 5 BD920W-2008........... Headstock Assembly - Parts List
Index No. Spindle...1 7 2107/1 Flange Joint 1 8 TS-1523031 Set Screw M6x10 1 9 2133 Bracket 1 11 GB6170-85 Hex Nut M6 2 12 2127 Collar ...1 13 61904 Ball Bearing 6904Z 1 14 2126/1...
User Manual - Page 25
Cover ...1 14 2104A Label - Thread Dial 1 15 BD920W-1108........... Spring ...1 22 BD920W-2004........... Description
Size
Qty
BD920N-3J.B.S. ...... 4-inch 3-Jaw Chuck (not shown 1 BD920N-CJ3 Chuck Jaw Set (set of 3; Parts List
Index No. not shown 1 BD920N-ST Spanner Tool for Chuck (not shown 1 FJ1001 4-Jaw Chuck 1-1/2" x 7 (not shown 1 FJ1002 1-1/2" x 8 ...
JET Tools BD-920W Reviews
Do you have an experience with the JET Tools BD-920W that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!