JET Tools JWBS-10OS Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools JWBS-10OS manuals!
Problems with JET Tools JWBS-10OS?
Ask a Question
Free JET Tools JWBS-10OS manuals!
Problems with JET Tools JWBS-10OS?
Ask a Question
Popular JET Tools JWBS-10OS Manual Pages
User Manual - Page 1
M-707200 Revision A3 04/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
10-inch Band Saw
Model JWBS-10OS
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
R
C
US
162920
Part No.
User Manual - Page 2
...JET sells through Friday. The specifications listed in your local distributor or visit the JET website. Parts; Motors; Metalworking Machinery; Manual Hoist Accessories; Warehouse & Dock products; JET...tear, improper repair, alterations or lack of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846.
JET has Authorized Service Centers located ...
User Manual - Page 3
... Blade Guide Positioning...12 Blade Guide Adjustment...12 Operating Controls...13 Adjusting Blade Tracking ...11 Replacing the Poly V-Belt ...14 Adjusting Poly V-Belt Tension...14 Grounding Instructions...15 General Information...15 115 Volt Operation ...15 Extension Cords...15 Troubleshooting ...16 Optional Accessories ...17 10" Band Saw Blades...17 Parts...18 Replacement Parts...18 Parts List...
User Manual - Page 4
...use this band saw for other part that is designed and intended ...repaired or replaced.
17. Check for other masonry products.
• Arsenic and chromium from that are specifically...JET disclaims any real or implied warranty and holds itself harmless from any injury that may cause serious injury.
3. Replace...and understand the entire owner's manual before turning it will operate properly...
User Manual - Page 5
.... Maintain a balanced stance at the correct speed and feed rate. Maintain tools with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage. Follow
instructions for the best and safest performance. Never leave the machine running...
User Manual - Page 6
... Table Size (in.) ...13-1/8 x 13-3/8 Table Size with instructions set forth in 25-3/4H; Specifications
Model Number...JWBS-10OS Stock Number ...707200 Band Saw Size (in.) ...10 Cutting Capacity (height) (in.)...4-1/8 Cutting Capacity (width) (in.) ...9-1/2 Maximum Rip Left of Blade w/Fence (in.)...5 Maximum Rip Right of trouble free operation if used in accordance with Extension (in.) ...13...
User Manual - Page 7
... the parts used throughout the Assembly section for assembly. 2 14mm Open End Wrench 1 Cross Point Screw Driver 1 Combination Square
7
Shipping Contents Contents of Shipping Container
01 Band Saw (A) 01 Table Insert (B) 01 Table (C) 01 Miter Gauge (D) 01 Fence (E) 01 Rail Guide (F) 04 Stand Leg (G) 02 Short Support Plate (H) 02 Long Support Plate (J) 01 Owner's Manual (not...
User Manual - Page 11
...Note: The JWBS-10OS Band Saw comes equipped with the blade.
Replace rail guide (F, Fig. 5). Note: A meter is recommended to precisely set tension the ...power source.
3. Set the blade tension with knob (T).
Disconnect machine from between the upper and lower blade guides (N, Q).
7. Bearing adjustments on blade tension. JWBS10OS-8) factory installed.
1. Before ...
User Manual - Page 12
... (A). Blade Guide Adjustment
Overview The blade guide assembly consists of two roller guides (bearings) positioned on a concentric shaft (C). an upper assembly and lower assembly (see Figure 12). Never make adjustments with a new one of a different size, the adjustment described above the material being replaced with the machine running! Referring to provide blade support.
Slide the...
User Manual - Page 15
... to whether the tool is green with all local codes and ordinances. Make sure the cord is not available. Repair or replace a damaged or worn cord immediately.
If it will not fit the outlet, have three-prong grounding plugs and three-pole receptacles that have the proper outlet installed by a qualified electrician.
Grounding Instructions
General Information...
User Manual - Page 16
...Extension cord too light or too long Low shop voltage
Base on page 10). Troubleshooting
Trouble
Probable Cause
Remedy
Saw stops or will not start
Does not make accurate 45o ... tension not set properly
Saw makes unsatisfactory cuts
Guide bearings not set accurately Fence not aligned with blade Warped wood
Check plug connections
Replace fuse, or reset circuit breaker
Replace cord
Check blade...
User Manual - Page 18
... Head Machine Screw M4x12 2 24 JWBS10OS-24.........LED Lamp Switch 1 25 JWBS10OS-25.........Start/Stop Switch 1 25-1..........
Having the Model Number and Serial Number of your machine available when you call 1-800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). Parts List
Index No. Parts
Replacement Parts
Replacement parts are listed on the...
User Manual - Page 19
...Table Insert 1 100........... JWBS10OS-101.......Fence Guide Rail 1 102........... TS-1482071 Hex Cap Screw M6x35 1 104........... Index No.
JWBS10OS-102.......Wing Screw 4 103........... JWBS10OS-104.......Carriage Bolt M6x30 1 105........... JWBS10OS-106.......Trunion 1
19 JWBS10OS-100.......Table...1 101........... Part No. JWBS10OS-105.......Slide Block 1 106...
User Manual - Page 20
... Index No. TS-1550071 Flat Washer M10 4 114........... JWBS10OS-121.......Short Support Plate 2 122........... JWBS10OS-114.......Extension Wing 1 115........... JWBS10OS-119.......Rubber Foot 4 120........... Part No. TS-1505011 Socket Head Cap Screw M10x16 2 112........... JWBS10OS-126.......Complete Fence Assembly 1 JWBS10OS-HB........Hardware Bag (see page 7 for contents
20...
JET Tools JWBS-10OS Reviews
Do you have an experience with the JET Tools JWBS-10OS that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!