Intel E2180 - Pentium Dual-Core 2.00GHz 800MHz 1MB Socket 775 CPU Support and Manuals
Get Help and Manuals for this Intel item
Most Recent Intel E2180 Questions
E2180 Overclocking Guide
E2180 + MS-7507-050 MSI Intel 945GCM7-Loverclocking
E2180 + MS-7507-050 MSI Intel 945GCM7-Loverclocking
(Posted by tuffytedy 14 years ago)
Intel E2180 Videos
Battle Los Angeles (2011) Gameplay GeForce 8600GT - Intel Dual Core E2180 - 2GB RAM
Duration: 6:27
Total Views: 414
Duration: 6:27
Total Views: 414
Sniper Elite v2 Gameplay |8600GT&E2180|
Duration: 8:30
Total Views: 441
Duration: 8:30
Total Views: 441
Need For Speed World on Pentium Dual Core E2180 2.00Ghz and HD5450
Duration: 2:06
Total Views: 483
Duration: 2:06
Total Views: 483
PCSX2 - WWE Smackdown vs Raw 2009 - Full Speed - E2180 @ 3.5Ghz
Duration: 5:05
Total Views: 66,501
Duration: 5:05
Total Views: 66,501
Popular Intel E2180 Manual Pages
Design Guide - Page 1
...;2 Duo Processor E6000 Δ and E4000 Δ Series - Intel® Pentium® Dual Core Processor E2000 Δ Series - Intel® Core™2 Duo Processor, Intel® Pentium® Dual Core Processor, and Intel® Celeron® Dual-Core Processor
Thermal and Mechanical Design Guidelines Supporting the: - Intel® Celeron® Dual-Core Processor E1000Δ Series...
Design Guide - Page 5
... A.2.2 Motherboard Deflection ...Case Temperature Reference Metrology 89
D.1 Objective and Scope 89
D.2 Supporting Test Equipment 89
D.3 Thermal Calibration and Controls 91
D.4 ...Installation 105
D.6 Thermocouple Wire Management 108
Appendix E Appendix F
Legacy Fan Speed Control 109
E.1 Thermal Solution Design 109
E.1.1 E.1.2
Determine Thermistor Set Points 109 Minimum Fan Speed Set...
Design Guide - Page 7
... 122 Figure 7-46. Thermistor Set Points 110 Figure 7-39. ...Intel® E18764-001 Reference Solution Assembly 145
Thermal and Mechanical Design Guidelines
7 Sheet 5 136 Figure 7-55. Solder Station Setup 102 Figure 7-28. Removing Excess Adhesive from IHS 107 Figure 7-36. Sheet 2 140 Figure 7-59. Sheet 3 131 Figure 7-50. Third Tape Installation 98 Figure 7-23. ATX/µATX Motherboard...
Design Guide - Page 12
... the benefits of the processor's integrated thermal management logic for clarity, the specific processor datasheet will be referenced. If needed for the product dimensions, thermal power dissipation and maximum case temperature. Introduction
1.1.3
Document Scope
This design guide supports the following processors:
• Intel® Core™2 Duo processor with 4 MB cache at Tc-max...
Design Guide - Page 15
...detailed mechanical specifications.
Figure 2-1. Package IHS Load Areas
Substrate
Top Surface of conflict, the package dimensions in the processor datasheet supersedes dimensions provided in this document. Refer to the datasheet for surface mounting to the motherboard through a land grid array (LGA) surface mount socket. A description of the socket with the motherboard via a LGA775...
Design Guide - Page 22
...is dictated by height restrictions for installation in the area potentially impacted by the real estate available on the motherboard and other design considerations (air duct...socket in Appendix H of this design guide.
• An overview of other BTX system considerations for thermal solutions can be obtained in the ATX Specification V2.1 and the microATX Motherboard Interface Specification...
Design Guide - Page 36
...temperature without the need for special software drivers or interrupt handling routines. The Thermal ...would initiate an OEM supplied interrupt service routine.
36
Thermal and Mechanical Design... for an illustration of the VID code will be configured to -active. ... is enabled by the BIOS setting a bit in a number ...and monitored in an MSR (model specific register). Thermal Management Logic and...
Design Guide - Page 38
...part basis there is achieved due to a smaller foot print and decreased sensitivity to noise. Since the DTS is factory set on a per sensor as required with ACPI compliant operating systems. The Thermal Monitor feature is a risk that do not meet the thermal profile specification...processor datasheet for the health monitor components to be updated at all times.
4.2.8
THERMTRIP# Signal
In ...
Design Guide - Page 39
...Intel® Quiet System Technology (Intel®
Thermal and Mechanical Design Guidelines
39 The DTS is no base value to the activation of the PECI interface see PECI Feature Set... proprietary single wire bus between the processor and the chipset or other health monitoring device.
The calculation of the LGA 775 socket. The usage model for TCONTROL with the ICH8 have both the DTS...
Design Guide - Page 43
... when installed in the same a BTX S2 reference chassis and commercially available power supply. Note: Appendix G gives detailed fan performance for the design. Balanced Technology Extended (BTX) Thermal/Mechanical Design Information
Table 5-2.
Acoustic performance is not a target for the Intel reference thermal solutions with 4 Wire PWM Controlled to ISO 7779. 2. The acoustic model...
Design Guide - Page 64
... constraints defined in both ATX Specification V2.1 and microATX Motherboard Interface Specification V1.1 documents.
64
Thermal and Mechanical Design Guidelines These drawings include height restrictions in Appendix H gives detailed reference ATX/μATX motherboard keep-out information for flammability at the system level.
This allows for Intel Reference ATX Thermal Mechanical Design...
Design Guide - Page 74
... the shipping system configuration. Operating
Fan Speed Operating Range with the hardware configuration of the motherboard and initial settings for availability of these tools.
7.4
Fan Hub Thermistor and Intel® QST
There is no closed loop control between the installed fans and sensors in optimizing the fan management and achieve acoustic goal. A Weighting Matrix...
Design Guide - Page 80
... plate that keep the dynamic load applied to the package within specifications published in the processor datasheet
Limiting board deflection may lead to heatsink preloads exceeding package maximum load specification. LGA775 Socket Heatsink Loading
A.2.5.1
Motherboard Stiffening Considerations
To protect LGA775 socket solder joint, designers need to drive their mechanical design to:
•...
Design Guide - Page 117
...thermal solution. The BIOS, at a minimum, must program the settings in selection of the design necessary to meet specifications. Should be specified or expanded by the component vendor to input ...has made provisions within the BIOS setup or other utility to account for consistency among designs.
Thermal and Mechanical Design Guidelines
117 The motherboard needs to have a fan ...
Design Guide - Page 131
...;ATX Motherboard Keep-out Footprint Definition and Height Restrictions for Enabling Components - NO
SHT.
Sheet 3
8
THIS DRAWING CONTAINS INTEL CORPORAT MAY NOT BE DISCLOSED, REPRODUCED, DI
D
1
7
ION CONFIDENTIAL INFORMATION. BOX 58119 SANTA CLARA, CA 95052-8119
2
SIZE CAGE CODE
DRAWING NUMBER
REV
D
C40819
3
SCALE: NONE DO NOT SCALE DRAWING SHEET 3 OF 3
1
131 SOCKET KEEP...
Intel E2180 Reviews
We have not received any reviews for Intel yet.