Hitachi GP 2 - GP2 1" Die Grinder (4.7 AMP) Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi GP 2 manuals!
Problems with Hitachi GP 2?
Ask a Question
Free Hitachi GP 2 manuals!
Problems with Hitachi GP 2?
Ask a Question
Popular Hitachi GP 2 Manual Pages
Instruction Manual - Page 3
....
NOTE emphasizes essential information.
3 Hazards that must be avoided by recognizing a potentially hazardous situation before operating or maintaining this Instruction Manual. Most accidents that has not been specifically recommended by observing appropriate safety procedures. An accident can often be avoided to prevent bodily injury or machine damage are identified by...
Instruction Manual - Page 4
...
5. DISCONNECT TOOLS. NEVER leave the tool connected to its power source before servicing, inspecting, maintaining, cleaning and before resuming operation of a guard or safety ...instructions:
READ ALL INSTRUCTIONS
1. NEVER OPERATE WITHOUT ALL GUARDS IN PLACE. ALWAYS WEAR EYE AND EAR PROTECTOR. Wear ear protector to replace the guard or safety feature before changing or checking any parts...
Instruction Manual - Page 5
....
13. DON'T OVERREACH. Follow instructions for cutting tree limbs or logs. Keep tool dry, clean, and free from work benches of this manual for more information about the proper... 12 of unnecessary tools, debris, furniture, etc.
9. SECURE WORKPIECE. Keep tools sharp and clean for which are being operated should be caught in moving parts. Inspect extension cords periodically and replace ...
Instruction Manual - Page 6
...clean so that may be properly repaired or replaced by children, individuals unfamiliar with your tool.
29. Check for use only extension cord intended for dust build-up ... influence of this Instruction Manual. Prevent potential injuries to the instructions provided herein. OUTDOOR USE EXTENSION CORD. Avoid the risk of parts, mounting, and any other part that makes you ...
Instruction Manual - Page 7
... AT THE RATED VOLTAGE. Check and inspect the tool for repairs by Hitachi may damage and crack plastic parts. DO NOT WIPE PLASTIC PARTS WITH SOLVENT. Do not wipe them with soapy water and dry thoroughly.
35. Replacement parts and/or accessories not supplied by a Hitachi authorized service center.
32. CAREFULLY HANDLE POWER TOOLS. NEVER LEAVE TOOL RUNNING...
Instruction Manual - Page 8
... fully in a polarized outlet only one blade is wider than the other). Do not change the plug in any way.
8 Repairs should be conducted only by a Hitachi authorized service center. If it still does not fit, contact a qualified electrician to install the proper outlet. English
REPLACEMENT PARTS AND ACCESSORIES
When servicing use only genuine Hitachi replacement parts and accessories.
Instruction Manual - Page 9
... a drop in line voltage resulting in loss of Cord in Feet (Meter)
0 - 25
26 - 50
51 - 100
101 - 150
(0 - 7.6)
(7.9 - 15.2) (15.5 - 30.5) (30.8 - 45.7)
Ampere Rating More Not More
AWG
Than Than
0 - 6
18
16
16
14
6 - 10
18
16
14
12
10 - 12
16
16
14
12
12 - 16
14
12
Not Recommended
WARNING:
Avoid electrical shock hazard...
Instruction Manual - Page 10
...; Although this system has no external grounding, you must still follow these precautions: ⅜ Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this
power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in wet environments. To keep the double insulation system...
Instruction Manual - Page 11
... NAME OF PARTS
Switch
Tail cover
Collet chuck
Bearing lid (B)
Housing Spindle Nose bracket Inner cover (B)
Fig. 1
Brush cap
SPECIFICATIONS
Motor Power ... instructions contained in this Instruction Manual may show details or attachments that differ from those on the tool unless you in this manual. Collet Check Capacity Weight
Single-Phase, Series Commutator Motor Single-Phase, 115V AC...
Instruction Manual - Page 12
...
(1) Wrench (43/64''(17mm)) (Code No.936638 1 (2) Wrench (15/32''(12mm)) (Code No.936553 1
OPTIONAL ACCESSORIES sold separately
⅜ Collet chuck (for the 1/4''(6mm) collet chuck.
⅜ Case NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.
APPLICATIONS
⅜ Finishing of dies for press working, die casting and moulding. ⅜ Finishing...
Instruction Manual - Page 13
...1/2" (13 mm). NEVER use an extension cord of your wheel. Refer to the following ...it may cause overheating, resulting in firing hazard.
5. Installing a wheel
WARNING: USING A WRONG SIZED WHEEL CAN CAUSE ...manual.
6. Check the work area has been thoroughly checked and prepared to make appropriate repairs. Some guidelines: (a) Dimension should be replaced or repaired.
4.
Instruction Manual - Page 16
... this portable grinder with a carbon brush which are subject to its wear limit.
The carbon brushes can then be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.
Always keep carbon brushes clean and ensure that only genuine replacement parts will be used, all service and repairs must be easily removed.
ᮣ 21 0.20" (5 mm)
0.47" (12 mm) Fig. 5
SERVICE AND REPAIRS
All...
Instruction Manual - Page 47
...10
15 Spring Washer
M4
16 Bearing Cover
17 Ball Bearing (608VVMC2EPS2L)
18A Inner Cover 19 Hexagon Socket Set ...Cord Clip 52 Spring
Item No. Part Name
53 Slide Bar 54 Cord Armor 56 Support (B)
57 Tapping Screw (W/Flange) 501 Wrench 12mm 502 Wrench 17mm 503 Collet Chuck
D4 × 16
Parts are subject to change without any obligation on the part of the HITACHI due to improvements.
47 Part...
Parts List - Page 2
...999- 084
34 937-847
...
DESCRIPTION BEARING LID (B)
NO. SOCKET SET SCREW M4X4
1
ARMATURE ASS'Y 110V ...CORD
1 (CORD ARMOR D10.1)
1 (CORD ARMOR D10.1) FOR SIN,KUW
CORD
1 (CORD ARMOR D8.8) FOR NGU,NZL,AUS
CORD
1 (CORD ARMOR D8.8)
CORD
1 (CORD ARMOR D8.8) FOR GBR,SAF
CORD
1 (CORD ARMOR D8.8) FOR USA,CAN
CORD
1 (CORD ARMOR D10.1) FOR SYR *: ALTERNATIVE PARTS...15 949-453
16 937-876
17 608-
Parts List - Page 3
...1
2
GP 2
STANDARD ACCESSORIES
ITEM NO.
CODE NO.
40 500- 2472
CORD
DESCRIPTION
40 500- 248Z CORD 40 500- 409Z CORD 41 985...BRUSH TERMINAL HITACHI LABEL ...CORD ARMOR D8.8 54 938- 051 CORD ARMOR D10.1 56 930- 153 SUPPORT (B) 57 984- 750 TAPPING SCREW (W/FLANGE) D4X16
NO. DESCRIPTION
501 936-553 WRENCH 12MM
502 936-638 WRENCH 17MM
503 932- 627 COLLET CHUCK 6MM
503A 932-666Z COLLET...
Hitachi GP 2 Reviews
We have not received any reviews for Hitachi yet.