Hitachi H45MR - 12 lb SDS Max Chipping Hammer 11 Amp Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi H45MR manuals!
Problems with Hitachi H45MR?
Ask a Question
Free Hitachi H45MR manuals!
Problems with Hitachi H45MR?
Ask a Question
Most Recent Hitachi H45MR Questions
Hitachi H45MR Videos
M?ot udarowy Hitachi H45MR 2009r. prod ( 23080 )
Duration: :21
Total Views: 164
Duration: :21
Total Views: 164
Popular Hitachi H45MR Manual Pages
Instruction Manual - Page 3
... a manner that has not been specifically recommended by observing appropriate safety procedures. Basic safety precautions are identified by WARNINGS on the power tool and in this Instruction Manual and in the "SAFETY" section of the safety precautions, warnings and operating instructions in the Instruction Manual before it occurs, and by HITACHI. NOTE emphasizes essential information.
3
Instruction Manual - Page 4
... cords are rated for the three wire grounded power cord and grounded power supply... follow all instructions. English
SAFETY
GENERAL SAFETY RULES
WARNING: Read and understand all instructions listed below, may...parts. (3) Avoid accidental starting. A moment of electric shock. (5) When operating a power tool outside, use the cord to install a polarized outlet. SAVE THESE INSTRUCTIONS...
Instruction Manual - Page 5
... all times. Any tool that is designed. (3) Do not use only identical replacement parts. Service (1) Tool service must be repaired. (4) Disconnect the plug from the power source before making any other practical way to secure and support the workpiece to a stable platform. Use of unauthorized parts or failure to control. (7) Check for misalignment or binding of moving...
Instruction Manual - Page 6
... the Instruction Manual.
7. English
SPECIFIC SAFETY RULES AND SYMBOLS
1. Hold tools by children, individuals unfamiliar with a "live " and shock the operator.
2. Contact with its own cord. ALWAYS wear ear protectors when using the power tool at all guards or safety features in place and in place. Never touch moving parts.
4. If maintenance or servicing requires...
Instruction Manual - Page 7
... Z87.1.
18. Definitions for repairs by a Hitachi authorized service center.
14. revolutions per minute Alternating current
7 Should a power tool be dropped or struck against hard materials inadvertently, it may result in electric shock. Wipe plastic parts with a soft cloth lightly dampened with solvent. ALWAYS attach the side handle and securely grip the Demolition Hammer. 21. no...
Instruction Manual - Page 8
... or thinners on the nameplate.
SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
8 English
...HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this
power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in this power tool, HITACHI...
Instruction Manual - Page 9
...
Nameplate
Grip (A)
Stopper
Trigger Switch
SPECIFICATIONS
Model Motor Power Source Current Full-load Impact Rate Weight
Housing
Brush Cap (Under the Tail Cover)
Fig. 1
Tail Cover
H 45MR Single-Phase, Series Commutator Motor
Single-Phase, 120 V AC 60 Hz 8.3 A
3000/min. 13.0 lbs (5.9 kg)
9 Some illustrations in this Instruction Manual is designed to assist you...
Instruction Manual - Page 10
Installing Tools (1) Clean the shank portion of the tool. (2) As shown in Fig. 2, pull grip (A) in the
direction of A, and insert the tool ...the direction of B in a state where grip (B) is slid in Fig. 2, pull grip (A), and pull out the tool. Tool Shank
A Front Cap
Fig. 2
Fig. 3
B A
Grip (A) Grip (B)
Fig. 4
10 English
ASSEMBLY
CAUTION: To prevent accidents, make sure to use the genuine...
Instruction Manual - Page 12
... the ON position, the power tool will start operating immediately and can cause serious injury.
3. The extension cord should be replaced or repaired.
4. Application examples: Installation of piping and wiring, sanitary facility installation, machinery installation, water supply and drainage work, interior jobs, harbor facilities and other civil engineering work area is far away from the power...
Instruction Manual - Page 13
... and the tool head is released. This should start operating. Repeat this procedure
for several minutes, and the hammer will heat, after which it is pressed to ON-LOCK. English
HOW TO USE THE DEMOLITION HAMMER
1.
Fig. 9
Proceed at a moderate work-rate, the use of use, the cylinder case becomes hot. CAUTION: After...
Instruction Manual - Page 14
...motor trouble....Using this demolition hammer with new...HITACHI carbon brush No. 73 indicated in the section MAINTENANCE AND INSPECTION.) Ask for name of the screws be removed. Replace the grease as abrasion is of the carbon brush. (See item 3 in Fig. 10.
4. Should any of parts) Loosen the set...service life. Inspecting the screws Regularly inspect all screws and ensure that time, replace...
Instruction Manual - Page 15
... all service and repairs must be performed by an Hitachi Authorized Service Center. This Parts List will eventually require servicing or replacement of parts because of the low viscosity type. Service parts list A: Item No. Used D: Remarks
CAUTION: Repair, modification and inspection of grease. Accordingly, some parts (i.e. Crank Cover Fig. 11
NOTE: ⅜ The Hitachi Electric Hammer...
Instruction Manual - Page 16
...) (Code No. 944458 1
OPTIONAL ACCESSORIES ........ STANDARD ACCESSORIES
(1) Bull Point (SDS max shank) (Code No. 313471 1 (2) Case (Code No. 320842) ...1 (3) Side Handle (Code No. 317103 1 (4) Allen Wrench (for 6 mm screw) (Code No. 944459 1 (5) Allen Wrench (for use a particular replacement part or accessory with this tool.
The use Only authorized HITACHI replacement parts and...
Instruction Manual - Page 17
... Work
(1) Scoop (SDS max shank type)
Overall Length 15-3/4" (400 mm)
Code No.
313476
⅜ Surface Roughing
(1) Bushing Tool
(2) Shank
(Code No. 313477)
(Code No. 313479)
⅜ Tamping
English
(1) Rammer
(2) Shank
(Code No. 313478)
(Code No. 313479)
⅜ Hammer Grease A 70 g (in a tube) (Code No. 981840) 30 g (in a tube) (Code No. 308471)
NOTE: Specifications are subject to...
Hitachi H45MR Reviews
We have not received any reviews for Hitachi yet.