Hitachi H45MR Support Question
Hitachi H45MR Support Question
Find answers below for this question about Hitachi H45MR - 12 lb SDS Max Chipping Hammer 11 Amp.Need a Hitachi H45MR manual? We have 1 online manual for this item!
Question posted by mrromer on November 10th, 2013
Connecting Rod
how is the piston and connection rod replaced
Current Answers
Related Hitachi H45MR Manual Pages
Instruction Manual - Page 3
... this Instruction Manual. Hazards that has not been specifically recommended by WARNINGS on the power tool and in death or serious injury. MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous ...occurs, and by the failure to observe basic safety rules or precautions. NEVER use this power tool in the sections which , if ignored, could result in this Instruction Manual and in a ...
Instruction Manual - Page 4
... instructions listed below, may result in electric shock, fire and/or serious personal injury.
Replace damaged cords immediately. Do not use an outdoor extension cord marked "WA" or "W"....not fit, contact a qualified electrician to follow all instructions. Electrical Safety (1) Double Insulated tools are rated for the three wire grounded power cord and grounded power supply system. (2)...
Instruction Manual - Page 5
... that are recommended by hand or against your body is designed. (3) Do not use only identical replacement parts. Service or maintenance performed by qualified repair personnel. Proper footing and balance enables better control of the tool in the Maintenance section of children and other practical way to secure and support the workpiece...
Instruction Manual - Page 6
....
12. Operate the power tool at all times. ALWAYS wear ear protectors when using the power tool at the rated voltage. Use right tool. Don't force small tool or attachment to replace the guard or safety feature before resuming operation of a guard or safety feature, be securely mounted to the tool should not be secure and tight.
11...
Instruction Manual - Page 7
..., and alcohol may result in electric shock. Never leave tool running unattended. Don't leave tool until it may be dropped or struck against hard materials inadvertently, it comes ...it immediately and arrange for symbols used on this tool may damage and crack plastic parts. ALWAYS attach the side handle and securely grip the Demolition Hammer. 21. English
13. ALWAYS be operating unusually, ...
Instruction Manual - Page 8
...assemble this
power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in this power tool, HITACHI has ... SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
8 Never use solvents, gasoline or thinners on the nameplate.
otherwise the plastic...
Instruction Manual - Page 9
.... 1
Tail Cover
H 45MR Single-Phase, Series Commutator Motor
Single-Phase, 120 V AC 60 Hz 8.3 A
3000/min. 13.0 lbs (5.9 kg)
9
Some illustrations in this manual. NEVER operate, or attempt any maintenance on your own power tool. English
FUNCTIONAL DESCRIPTION
NOTE: The information contained in this Instruction Manual is designed to assist you have...
Instruction Manual - Page 10
...
A Front Cap
Fig. 2
Fig. 3
B A
Grip (A) Grip (B)
Fig. 4
10
Deciding Working Position of Tool The tool can be turned every 30 degrees and can be fixed at the position of 12 steps. (1) As shown in Fig. 4, the blade angle can be freely changed if the grip (A) is turned in the direction of B in a state...
Instruction Manual - Page 11
Grip
A
B
Fig. 5
Fig. 7
English Fig. 6 Fig. 8
11 Move the side handle The side handle can be fixed at any desired position; 360 degrees, and can also be fixed at any position in ...
Instruction Manual - Page 12
... Contact a licensed electrician to prescribed precautions.
12 English
OPERATION
APPLICATIONS
⅜ Demolishing concrete, ... tool will start operating immediately and can cause serious injury.
3. If such a fautly receptacle is connected ...to the power source requirements specified on the product nameplate.
2. Extension cord When the work .
The extension cord should be replaced...
Instruction Manual - Page 13
... trigger for continuous operation. After placing the tip of the machine and by firmly
holding the hammer by both hands, you can be careful not to ON-LOCK. Even when the switch is...several minutes, and the hammer will impair efficiency.
3. English
HOW TO USE THE DEMOLITION HAMMER
1. By utilizing the empty weight of the tool on , the motor is running and the tool head is pulled and OFF...
Instruction Manual - Page 14
...hammer with new ones which are forced to the timing replacement period of the carbon brush. (See item 3 in motor trouble. At that they are properly tightened. In addition, always keep carbon brushes clean and ensure that you are consumable parts. Grease replacement... malfunction, sharpen or replace the tool as soon as described below.
(1) Grease Replacement Period Inspect the grease...
Instruction Manual - Page 15
...7. When the grease is of power tools, the safety regulations and standards prescribed in the crank case.
3 After replacing the grease, reassemples the crank cover securely...advancements. MODIFICATIONS: Hitachi Power Tools are constantly being improved and modified to cover the connecting rod) of grease. Crank Cover Fig. 11
NOTE: ⅜ The Hitachi Electric Hammer Grease A is
consumed, ...
Instruction Manual - Page 16
... (SDS max shank type)
Overall Length Code No.
11-1/32" (280 mm) 15-3/4" (400 mm)
313473
313474
16
STANDARD ACCESSORIES
(1) Bull Point (SDS max shank) (Code No. 313471 1 (2) Case (Code No. 320842) ...1 (3) Side Handle (Code No. 317103 1 (4) Allen Wrench (for 6 mm screw) (Code No. 944459 1 (5) Allen Wrench (for use a particular replacement part or accessory with this tool...
Instruction Manual - Page 17
... No.
15-3/4" (400 mm) 313475
⅜ Scooping Work
(1) Scoop (SDS max shank type)
Overall Length 15-3/4" (400 mm)
Code No.
313476
⅜ Surface Roughing
(1) Bushing Tool
(2) Shank
(Code No. 313477)
(Code No. 313479)
⅜ Tamping
English
(1) Rammer
(2) Shank
(Code No. 313478)
(Code No. 313479)
⅜ Hammer Grease A 70 g (in a tube) (Code No. 981840) 30...
Similar Questions
Hitachi C12lsh Wiring Power Swith
I neglected to take a picture of the wiring of the switch. It has 3 connections.... One for the powe...
I neglected to take a picture of the wiring of the switch. It has 3 connections.... One for the powe...
(Posted by wsigurdson 9 years ago)
What Is In The Fuel Rods
(Posted by jcole5778 11 years ago)
How To Use The Dh50sbk As A Chipping Hammer?
How do I convert the hammer drill function to a chipping hammer function?
How do I convert the hammer drill function to a chipping hammer function?
(Posted by llsconstruction 12 years ago)
Where Can I Get A Free Manual On The Hitachi C12rsh 12' Slide Compound Miter Saw
(Posted by kathy86883 14 years ago)