Hayward Power-Flo II Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward Power-Flo II manuals!
Problems with Hayward Power-Flo II?
Ask a Question
Free Hayward Power-Flo II manuals!
Problems with Hayward Power-Flo II?
Ask a Question
Most Recent Hayward Power-Flo II Questions
I Like To Know How The Wiring Is On The Pump Itself Not The Connection The Pump
I I like to know how the Hayward pump flow LX is wired on the inside before the connection
I I like to know how the Hayward pump flow LX is wired on the inside before the connection
(Posted by born2drywall 4 years ago)
Can I Change The Pump Housing Position On Hayward Power Flo Ii
(Posted by Bebamgane 9 years ago)
Power Flo Lx Pump Will Not Run
(Posted by kazamans 10 years ago)
Where Can I Find Thru Bolts For Hayward Pump
(Posted by Jonesst 11 years ago)
Pump Motor Switch Wiring Diagram
I was replacing a bad power switch on my hayward power flo matrix pump and I acciddentally pulled th...
I was replacing a bad power switch on my hayward power flo matrix pump and I acciddentally pulled th...
(Posted by centaur511 11 years ago)
Popular Hayward Power-Flo II Manual Pages
Model: ALL - Page 1
... ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY.
*Only units equipped with 3' twist-lock cords or furnished without a cord for permanent wiring are specifically engineered for the demanding requirements of this product. C
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
Power-Flo LX™ / Power-Flo II™ Pump Series
The Hayward® Power-Flo LX™ and Power-Flo II™ Pump...
Model: ALL - Page 2
... use with hot tubs and spas if so marked. Power-Flo LX™ / Power-Flo II™ Pump Series
PRODUCT REGISTRATION
(Retain For Your Records)
DATE OF INSTALLATION
INITIAL PRESSURE GAUGE READING (CLEAN FILTER
PUMP MODEL HORSEPOWER
FILTER MODEL SERIAL NUMBER
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always...
Model: ALL - Page 3
.... Installation of pump and suction outlets must be OPEN when
starting the filter system. Pumps, filters, and other equipment.
WARNING - WARNING - To reduce the risk of Electric Shock. WARNING - If screws are lost, order replacement parts from pumps with all applicable local building codes. Suction from your pump is protected by a GFCI. Power-Flo LX™ / Power-Flo II...
Model: ALL - Page 4
...-priming Power-Flo II™ pumps may be installed up to force hose connector fitting past this stop. Pump motors require free circulation of air for servicing pump and ...pump suction and outlet ports have molded-in a damp or non-ventilated location. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions
Pump Location
The Power-Flo LX™ pump MUST be installed...
Model: ALL - Page 5
...To avoid dangerous or fatal electrical shock, turn OFF power to local codes and regulations. NOTE: All electrical wiring MUST be more than 110% of Plumbing and Mechanical Officials (IAPMO) standards. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions (cont.)
Fittings
Fittings restrict flow. Avoid fittings that the wire size is less than 90% or more than 10...
Model: ALL - Page 6
...on strainer cover. ƒ Replace strainer cover on vertical length of suction lift and horizontal length of suction pipe. NOTE: Tighten strainer cover by hand only (no wrenches) ¼ turn clockwise to pool/spa system directly in suction and outlet pipes. 3. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions (cont.)
Electrical (cont.)
Wiring (cont.)
In case...
Model: ALL - Page 7
...
serviceman repair/replace wiring as possible. Prime pump according to base. 4. A.
Shaft Seal Change Instructions
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ AND FOLLOW ALL INSTRUCTIONS
When servicing electrical equipment, basic safety precautions should attempt rotary seal replacement. The National Electrical Code requires either a three (3) foot maximum twist-lock cord set with...
Model: ALL - Page 8
... undersized wiring or extension cord use petroleum or silicone lubricants as these can build up on pump cover. etc. 2. Finally, slide strainer housing forward and remove.
3.
Loosen four (4) motor through bolts removed in place onto the motor shaft. Insert basket and fasten strainer cover. 16. Power-Flo LX™ / Power-Flo II™ Pump Series
Shaft Seal Change Instructions (cont...
Model: ALL - Page 9
...clean or replace cartridge. 3. Noisy Pump - Holding hand over the bottom port with a vacuum gauge). Foreign matter in OPEN position. 2.
Power-Flo LX™ / Power-Flo II™ Pump Series
Troubleshooting (cont... seal damage which will sometimes prove this
manual. Generally, Check For:
1. backwash as per manufacturer's instructions; Loose stones/debris hitting impeller could be...
Model: ALL - Page 10
SPX1515Z1E
Motor (for SP1580X15) - 1-1/2 HP
---- SPX1510Z2E)
Model No.
Description
Model No. SPX1510Z1XE
Motor (for SW1585X20) - 2 HP
---- Power-Flo LX™ / Power-Flo II™ Pump Series
Replacement Parts
Parts Diagram
Parts Listing
Ref. on Original Equipment
SPX1705AA SPX1500Y2 (6 Req'd.)
---SPX1500Z1E SPX1510Z1E* SPX1510Z1XE*
------------SPX1500CAP SPX1500RA ...
Model: ALL - Page 11
... of ONE (1) year from the date of purchase, or to state.
*Supersedes all previous publications. For further Hayward dealer or service center information, contact Hayward customer service department.
Power-Flo LX™ / Power-Flo II™ Pump Series
HAYWARD® LIMITED WARRANTY
This pump was inspected before shipment from the date of purchase. To original purchasers of this...
Hayward Power-Flo II Reviews
We have not received any reviews for Hayward yet.