Hayward Power-Flo II Support Question
Hayward Power-Flo II Support Question
Find answers below for this question about Hayward Power-Flo II.Need a Hayward Power-Flo II manual? We have 1 online manual for this item!
Question posted by centaur511 on July 26th, 2012
Pump Motor Switch Wiring Diagram
I was replacing a bad power switch on my hayward power flo matrix pump and I acciddentally pulled the yellow wire clip off of the other end connection. where does it go back to? do you have a schematic or is it one of the numbered connections?
Current Answers
Related Hayward Power-Flo II Manual Pages
Model: ALL - Page 1
ISPF SERIES Rev. C
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
Power-Flo LX™ / Power-Flo II™ Pump Series
The Hayward® Power-Flo LX™ and Power-Flo II™ Pump Series are UL-Listed.
Corporate Headquarters: 620 Division Street Elizabeth, NJ 07207
U.S.A: 1 Hayward Industrial Drive Clemmons, NC 27012
2935 Sidco Drive Nashville, TN 37204
2875 Pomona Blvd.
...
Model: ALL - Page 2
... to pool structure. Connect a No. 8 AWG (8.4 mm²) solid copper bonding wire to the pressure wire connector provided on -ground pools) advises that it cannot be positioned to all metal parts of air for storage. The ANSI/NSPI 4 Standard (above -ground swimming pools and may result in a damp or non-ventilated location. Power-Flo LX™ / Power-Flo II™ Pump Series...
Model: ALL - Page 3
.... Suction in compliance with only one (1) wall of the pool or spa. Replace damaged, broken, cracked, missing, or unsecured drain covers and suction outlets immediately. Do NOT connect to bleed air from pumps with all applicable local building codes. WARNING -
Power-Flo LX™ / Power-Flo II™ Pump Series __________
____________
NOTE: The National Electrical Code (NEC...
Model: ALL - Page 4
...connections on pipe or hose joints. do NOT over-tighten fitting or you face the open end of the fitting, beginning at pump and run is reduced considerably;
Self-priming Power-Flo II™ pumps may be solid - Pump motors...). ƒ Allow for servicing pump and piping. For pump suction on a firm, level base or pad to four (4) feet above the pool water line. The base MUST be...
Model: ALL - Page 5
...) in pool or double suction (skimmer and main drain).
Connect motor ground terminal to inspect and repair electrical system. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions (cont.)
Fittings
Fittings restrict flow. Use a non-entrapping suction fitting in circuit;
If GFCI trips and won't reset, consult electrician to electrical service ground. Run wire...
Model: ALL - Page 6
.... ƒ Replace strainer cover on vertical length of suction lift and horizontal length of suction pipe. Running pump dry may damage pump and voids warranty.
CAUTION - WARNING - Do NOT block pump suction.
If pump does NOT prime within ten minutes, stop motor and determine cause. WARNING - CAUTION -
Pump should prime. Power-Flo LX™ / Power-Flo II™ Pump Series...
Model: ALL - Page 7
... (3) foot maximum twist-lock cord set with risk of the filter. 2.
Power-Flo LX™ / Power-Flo II™ Pump Series
Storage/Winterization
WARNING - Explosion Hazard. Allowing the pump to base. 4. Drain all inlets to explode, with a GFCI
protected receptacle or hard wire (conduit) connection for reactivation of severe injury or death to use
extension cords. Inspect all...
Model: ALL - Page 8
... loose wiring connections; Bypass it is equipped with the polished flat surface facing out. 12. Check For:
1. Shut off if power supply drops before heat damage can contribute to pool. Finally, slide strainer housing forward and remove.
3. Carefully insert the motor shaft through bolts until the problem is again up on pump cover.
Power-Flo LX™ / Power-Flo II™ Pump...
Model: ALL - Page 9
... on skimmer wall.
3. Power-Flo LX™ / Power-Flo II™ Pump Series
Troubleshooting (cont.)
Motor Hums, But Does NOT Start - Binding of filter, valve partially closed (high gauge reading). Pump Won't Prime
1. a. Check voltage to clean. iv. Generally, Check For:
1. Clogged or restricted strainer or suction line; backwash as necessary.
ƒ Hayward pumps have 5"-6" of vacuum...
Model: ALL - Page 10
Power-Flo LX™ / Power-Flo II™ Pump Series
Replacement Parts
Parts Diagram
Parts Listing
Ref.
on Original Equipment
Refer to a "2" (i.e. Motor (for SP1775) - 3/4 HP
----
----
9 Motor (for SP1780) - 1 HP Motor (for SW1585X20) - 2 HP
---- SPX1515Z1E
Motor... with Gasket
SPX1700FG
SPX1700FG
17 C-Clip
SPX1515C
SPX1515C
* To order 2-speed motor, change "1" in suffix of ...
Model: ALL - Page 11
...not be repaired or replaced, at our option, without charge.
Some states do not allow a limitation on these other rights, which vary from the date of purchase.
Power-Flo LX™ / Power-Flo II™ Pump Series
HAYWARD® LIMITED WARRANTY
This pump was inspected before shipment from Hayward:
□ Pump □ Filter □ Automatic Pool Cleaner □ Light □...
Similar Questions
Hayward Power Flo Matrix - Sp500z2 Looking For A Lid And 0 Ring For Pump
looking for a lid for the Hayward power flo sp5500z2
looking for a lid for the Hayward power flo sp5500z2
(Posted by tonjapatton 2 years ago)
I Like To Know How The Wiring Is On The Pump Itself Not The Connection The Pump
I I like to know how the Hayward pump flow LX is wired on the inside before the connection
I I like to know how the Hayward pump flow LX is wired on the inside before the connection
(Posted by born2drywall 4 years ago)
Can I Change The Pump Housing Position On Hayward Power Flo Ii
(Posted by Bebamgane 9 years ago)
How Do You Take Off Pump Motor For Hayward Power Flo Matrix
(Posted by toshiz 10 years ago)