Hayward HCP Pump Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward HCP Pump manuals!
Problems with Hayward HCP Pump?
Ask a Question
Free Hayward HCP Pump manuals!
Problems with Hayward HCP Pump?
Ask a Question
Popular Hayward HCP Pump Manual Pages
HCP Series LITCPOMA10 - Page 2
... Manual 2.2 Important Safety Instructions 2.3 Nameplate Ratings 2.4 Liability 2.5 Standards 2.6 General Instructions in Relation to the Main Power Supply
6.1 Electrical 6.2 Voltage 6.3 Emergency Shutoff 6.4 Grounding/Bonding 6.5 Wiring 6.6 Engineering Specs
2 Packing, Transport and Storage
4.1 Handle with Care 4.2 Clean-Up
5. Dimensions 4. Installation
5.1 Location 5.2 Foundation 5.3 HCP Pump...
HCP Series LITCPOMA10 - Page 4
... Support: 1-800-657-2287
Hayward Commercial self-priming pumps provide a technologically advanced alternative to see nameplate ratings) Consumption: See nameplate ratings Frequency: See nameplate ratings R.P.M.: 3,450 Shaft: Stainless steel
Pump:
Water temperature: Maximum 122ºF Maximum pressure: 40 PSI Impeller model: Closed Type of your pump, READ THIS MANUAL CAREFULLY! HCP pumps...
HCP Series LITCPOMA10 - Page 5
...manufacturer in relation to the functioning of the equipment with this equipment, including the following:
To reduce the risk of injury, allow only trained professionals to install and service this manual, look for storage and reassembled to hazards. This pump... the HCP Series Self-Priming Pumps. replace if missing or damaged.
2.1 SAFETY SIGNS USED IN THE MANUAL
All instructions referring to...
HCP Series LITCPOMA10 - Page 6
... operating equipment. 1.
Remove trap lid and retighten by persons or damages caused to other instructions affixed by the manufacturer to the choice, handling, installation, starting and maintenance of the warranty.
2.5 STANDARDS
Our HCP Series pumps are manufactured in this manual, in system before operating or testing equipment. Do not connect system to be less than...
HCP Series LITCPOMA10 - Page 7
... for which the user is in contact. Spare parts that its condition, installation, initial and subsequent use of others , is not permitted and releases the manufacturer or distributor from the main power supply. Compliance with U.S. The use are in movement or which , when functioning, are correct. Installation, repair and maintenance operations will be originals from the...
HCP Series LITCPOMA10 - Page 8
... Data
100
90
80
70
60
50
40
30 0
50
100 150
200
250 300
350
400
450 500
550
600 650
700
F low (G P M )
PERFORMANCE - HCP Single Speed Pumps
PERFORMACE - ELECTRICAL SPECIFICATIONS:
Commercial Pump Ordering Information
Model No.
PERFORMANCE - PERFORMACE - DIMENSIONS Total Dynamic Head (Ft)
3.
HCP Series LITCPOMA10 - Page 10
...-
Amb.) listed on the motor model plate. Vibration free. • Be provided with necessary hold-down bolts, washers, and shims. • Allow pump inlet to be as close to ...
10 Installation
5.1 LOCATION ATTENTION Only qualified, licensed personnel should install pump and wiring. The place where the pump motor is enough space and light around the pump for servicing pump and ...
HCP Series LITCPOMA10 - Page 11
... SHORT AS POSSIBLE BUT AT LEAST
6 TIMES PIPE DIAMETER (TO STABILIZE FLOW)
FROM NEAREST FITTING TO STRAINER. MAXIMUM
SUCTION LIFT 10'.
4" UNION SUPPORT PIPE
5.4 HCP PUMP PIPING - SUCTION LIFT INSTALLATION
Figure 5.3 Installation Diagram.
THE DISTANCE TO THE FIRST ELBOW MUST BE AT LEAST 5 TIMES THE PIPE DIAMETER. 4" UNION
FROM POOL SUCTION PLUMBING. THE DISTANCE TO THE...
HCP Series LITCPOMA10 - Page 12
... equipment, power supply, and installation
requirements, this manual does not make specific recommendations concerning auxiliary equipment or fusing/wiring. Disconnect power at service panel before connecting to the manufacturer of rated voltage when motor is familiar with the National Electrical Code, as well as all applicable local codes and ordinances. Match supply voltage...
HCP Series LITCPOMA10 - Page 13
Clearly mark this switch and mount it to circuit;
Permanently ground motor. be permanently connected to be turned manually using the discharge valve. Single phase motors: Follow motor manufacturer's instructions to electrical service ground. ATTENTION
Ensure that the motor does not exceed the amperage indicated on the motor end, which permits it in case of...
HCP Series LITCPOMA10 - Page 15
... code. To avoid air locking, do not allow high spots in discharge lines. Recommended Pump Section Layout.
15 NOTICE If pump suction becomes clogged, pump will cavitate, damaging pump internal parts. Use at the pump and run pipe away from the pump.
7.6 PIPING - Suction pipe must
have valves in suction and discharge pipes. To prevent strain on the pump, support...
HCP Series LITCPOMA10 - Page 16
...installing it is discharged from the valve. 4. Ensure all parts to verify they
are sealed properly to starting the circulating pump system. Immediately inspect all pump...air relief valve (if available) on pump or strainer body, support pipe independently of water (not air ...manual air relief valve until
a steady stream of pump/strainer. Fittings restrict flow; When installing...
HCP Series LITCPOMA10 - Page 17
Water acts as necessary.
• Hayward pumps have self-lubricating motor bearings and shaft seals. lf no leakage occurs, stand at least 10 feet from the valve . See Troubleshooting Guide. Failure to close the manual air relief valve when a steady stream of water (not air or air and water) is discharged from pump and/or filter...
HCP Series LITCPOMA10 - Page 24
...
HCXP6008A
HCXP6009A
HCXP6010A
HCXP55MOTOR HCXP75MOTOR HCXP100MOTOR HCXP125MOTOR
HCXP6024A
Hayward Commercial is a registered trademark of 10) Seal Plate Set Seal Plate Screw Set Union Connection Set (Qty. HCP SERIES COMMERCIAL SELF-PRIMING PUMPS MANUAL
Description
Lid Bolt Set Pump Lid Filter Basket Internal O-Ring Set Seal Set Pump Casing Pump Support Drain Plug Set (Qty.
Parts Diagram - Page 3
...MOTOR HCP75 MOTOR HCP100 MOTOR HCP125 MOTOR BEARINGS SET-HCP55 (QTY. OF 4)
HCXP6022A
PUMP STRAINER BODY
HCXP6023A
PUMP SUPPORT BOLT SET (QTY. Part Number HCXP6017A
Description SEAL PLATE SET
HCXP6018A
SEAL PLATE SCREW SET (QTY. OF 4) PUMP CASING BOLTS (QTY. OF 4)
Components
PLASTIC FLANGE DIFFUSER GASKET SEAL SET 14 SEAL SET 15 FLANGE O-RING IMPELLER O-RING FLAT GASKET
Drawing...
Hayward HCP Pump Reviews
We have not received any reviews for Hayward yet.