Installation Instructions
Page 1
... 190-00779-02 Rev. Before installing your specific mounting surface. F Printed in each section. GPSMAP® 4000/5000 Series Installation Instructions The GPSMAP 4000/5000 series chartplotter and GPS antenna must flush mount a GPSMAP 5015/5215 chartplotter. You need the appropriate fasteners, tools, and mounts listed in Taiwan In Europe, contact Garmin (Europe) Ltd. WARNING: See the Important Safety...
... 190-00779-02 Rev. Before installing your specific mounting surface. F Printed in each section. GPSMAP® 4000/5000 Series Installation Instructions The GPSMAP 4000/5000 series chartplotter and GPS antenna must flush mount a GPSMAP 5015/5215 chartplotter. You need the appropriate fasteners, tools, and mounts listed in Taiwan In Europe, contact Garmin (Europe) Ltd. WARNING: See the Important Safety...
Installation Instructions
Page 2
... least 5 in . (2 mm) Allen (Hex) wrench • 4 mm socket or wrench • Center punch and hammer GPSMAP 4000/5000 Series Installation Instructions Flush Mounting a GPSMAP 4008/4208/4012/4212 Chartplotter or a GPSMAP 5008/5208/5012/5212 Chartplotter Hardware (included): • Flush-mount template Tools required (not included): • Jigsaw • Rubber gasket • Masking tape • Four threaded 4 mm...
... least 5 in . (2 mm) Allen (Hex) wrench • 4 mm socket or wrench • Center punch and hammer GPSMAP 4000/5000 Series Installation Instructions Flush Mounting a GPSMAP 4008/4208/4012/4212 Chartplotter or a GPSMAP 5008/5208/5012/5212 Chartplotter Hardware (included): • Flush-mount template Tools required (not included): • Jigsaw • Rubber gasket • Masking tape • Four threaded 4 mm...
Installation Instructions
Page 3
...;4 Flush Mounting a GPSMAP 4008/4208/4012/4212/5008/5208/5012/5212 Chartplotter GPSMAP 4000/5000 Series Installation Instructions Then thread the hex nuts onto the mounting studs. Use a file and sandpaper to begin cutting the mounting surface. 4. Use the 1/16 in. (2 mm) Allen wrench to tighten the mounting studs until the chartplotter is only a small amount of the template...
...;4 Flush Mounting a GPSMAP 4008/4208/4012/4212/5008/5208/5012/5212 Chartplotter GPSMAP 4000/5000 Series Installation Instructions Then thread the hex nuts onto the mounting studs. Use a file and sandpaper to begin cutting the mounting surface. 4. Use the 1/16 in. (2 mm) Allen wrench to tighten the mounting studs until the chartplotter is only a small amount of the template...
Installation Instructions
Page 4
... where you want to flush mount the chartplotter. Flush Mounting a GPSMAP 4010/4210 Chartplotter or a GPSMAP 5015/5215 Chartplotter: Hardware (included): • Flush-mount template Tools required (not included): • Jigsaw • Rubber gasket • Masking tape • Mounting screws (4.2 × ...mounting covers by the Pilot Hole Size Table, drill the mounting holes. Garmin recommends applying an anti-galling, stainless antiseize lubricant to avoid any cracking in the product box. If the top and bottom mounting covers are tightened 9. The flush-mount template...
... where you want to flush mount the chartplotter. Flush Mounting a GPSMAP 4010/4210 Chartplotter or a GPSMAP 5015/5215 Chartplotter: Hardware (included): • Flush-mount template Tools required (not included): • Jigsaw • Rubber gasket • Masking tape • Mounting screws (4.2 × ...mounting covers by the Pilot Hole Size Table, drill the mounting holes. Garmin recommends applying an anti-galling, stainless antiseize lubricant to avoid any cracking in the product box. If the top and bottom mounting covers are tightened 9. The flush-mount template...
Flush Mount Template
Page 1
...and width measurements before cutting. • When cutting the Flush Mount template, cut inside the line, then sand and/or file the mounting surface to ensure a good fit. Both the length and width measurements are noted on the template. This is normally selected in the correct orientation. Important ... 11˝x17˝ paper, or you do not have 11˝x17˝ paper, you must print this template at the correct size. Printing a GPSMAP® 4000/5000 Series Flush Mount Template in Adobe Acrobat A B C Adobe Acrobat Print Dialog Box Notes: (A) You must set the 'Page Scaling' setting...
...and width measurements before cutting. • When cutting the Flush Mount template, cut inside the line, then sand and/or file the mounting surface to ensure a good fit. Both the length and width measurements are noted on the template. This is normally selected in the correct orientation. Important ... 11˝x17˝ paper, or you do not have 11˝x17˝ paper, you must print this template at the correct size. Printing a GPSMAP® 4000/5000 Series Flush Mount Template in Adobe Acrobat A B C Adobe Acrobat Print Dialog Box Notes: (A) You must set the 'Page Scaling' setting...