Fujitsu MHM2150AT - Mobile 15 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MHM2150AT manuals!
Problems with Fujitsu MHM2150AT?
Ask a Question
Free Fujitsu MHM2150AT manuals!
Problems with Fujitsu MHM2150AT?
Ask a Question
Popular Fujitsu MHM2150AT Manual Pages
Manual/User Guide - Page 19
... of breather 3-6 Figure 3.5 Surface temperature measurement points
(Sample: MHL2300AT) 3-7 Figure 3.6 Service area (Sample: MHL2300AT) 3-8 Figure 3.7 Handling cautions 3-9 Figure 3.8 Connector locations (Sample... Jumper location 3-12 Figure 3.12 Factory default setting 3-13 Figure 3.13 Jumper setting of master or slave device 3-13 Figure 3.14 CSEL setting 3-14 Figure 3.15 Example (1) of Cable ...
Manual/User Guide - Page 23
The disk drive supports an external data rate up to 55°C).
(3) Low noise and vibration
In Ready status, the noise...are described.
(1) Compact
The MHL2300AT has 3 built-in the head positioning mechanism greatly increases the positioning speed. The MHM2200AT, MHM2150AT and MHM2100AT have an internal data rate up to 10 GB (formatted) on one disk using the 16/17 MTR recording method and...
Manual/User Guide - Page 30
...repaired by external factors, such as follows:
Total operation time in all fields
MTBF=
(H)
number of the DE surface temperature. Disk drive defects do not include failures caused by a specialist maintenance staff member.
(3) Service... cable.
(2) Mean time to repair (MTTR)
The mean time to defects that involve repair, readjustment, or replacement. Refer to item (3) in Subsection...
Manual/User Guide - Page 63
.... HDIC generates a write unsafe signal (WUS) when a write error occurs due to the timechart, the disk drive terminates self-calibration...calibration according to head short-circuits or head disconnection, that sets the bias current to the track requested by serial I/O. Every.... In other words, if a disk read or write service is a block diagram of the read/write circuit.
4.6.1 Read/write preamplifier...
Manual/User Guide - Page 67
...recording method, data area is divided into zones by radius and the data transfer rate is set the data transfer rate. The Viterbi detection circuit demodulates data according to the survivor path ...is different from the flash digitizer circuit is nearly constant. The MPU transfers the data transfer rate setup data (SD/SC) to the RDC that includes the Digital PLL circuit to the Modified Extended...
Manual/User Guide - Page 83
...reading) or from the host to the host.
The IDENTIFY DEVICE information indicates whether the device supports the LBA mode. signals are LBA bits.
under the LBA mode proceeds in the Device/Head ... 0, Head 0, Sector 1]
Even if the host system changes the assignment of the CHS mode by setting bit 6 in the ascending order with the DMACK-signal. and CS1- This signal hand shakes with ...
Manual/User Guide - Page 91
... Command code and parameters
Table 5.3 lists the supported commands, command code and the registers that needed parameters are written.
Table 5.3 Command code and... DEVICE DMA
1
SET FEATURES
1
SET MULTIPLE MODE
1
SET MAX
1
READ NATIVE MAX ADDRESS 1
EXECUTE DEVICE DIAGNOSTIC 1
READ LONG
0
WRITE LONG
0
READ BUFFER
1
WRITE BUFFER
1
IDLE
1
1
Command code (Bit)
Parameters ...
Manual/User Guide - Page 100
...
*1 If the command is terminated due to an error, the remaining number of sectors of the corresponding sector(s).
If an error occurs when writing to the target sector, retries are written to data transfer, see Subsection 5.4.2. 5.3 Host Commands
At command issuance (I/O registers setting contents)
1F7H(CM) 1F6H(DH)
1F5H(CH) 1F4H(CL) 1F3H...
Manual/User Guide - Page 110
...Firmware revision (ASCII code, 8 characters, left) Model name (ASCII code, 40 characters, left) Maximum number of sectors per interrupt on READ/WRITE MULTIPLE command Reserved Capabilities *3 Reserved PIO data transfer mode *4 Reserved Enable/disable setting... number *9 Minor version number (not reported) Support of command sets *10 Support of command sets *11 Support of 8)
Word 23-26 27-46
47
...
Manual/User Guide - Page 112
...
Bit 15-9: Reserved
Bit 8:
Multiple sector transfer 1=Enable
Bit 7-0:
Transfer sector count currently set by IDENTIFY DEVICE command (4 of 8)
Bit 13: Standby timer value. 5.3 Host Commands
Table 5.4 Information to be read by READ/WRITE MULTIPLE command without interrupt supports 2, 4, 8 and 16 sectors.
*7 Word 63: Multiword DMA transfer mode
Bit 15-8: Currently used...
Manual/User Guide - Page 113
... the DEVICE RESET command. Bit 5:
'1' = Supports the write cache function.
Bit 1:
'1' = Supports the Security Mode feature set .
Bit 4:
'1' = Supports the PACKET command feature set .
Bit 12: '1' = Supports the WRITE BUFFER command. Bit 8:
'1' = Supports the SERVICE interrupt.
Bit 3:
'1' = Supports the power management feature set .
*11 WORD 83
Bits 15-7: Undefined
Bit...
Manual/User Guide - Page 114
... 5
Enables the Power-Up In Standby function. Bit 3:
'1' = Supports the Advanced Power Management feature set . Bit 2:
'1' = Supports the CFA (Compact Flash Association) feature set .
Bit 1:
'1' = Supports the READ/WRITE DMA QUEUED command. Bit 8:
'1' = Enables the SERVICE interrupt.
Bit 4:
'1' = Enables the Removable Media Status Notification function.
Bit 11: Undefined...
Manual/User Guide - Page 120
...Sector Count register.
If the value of the Sector Count register is not a supported block count, an ABORTED COMMAND error is posted and the READ MULTIPLE and WRITE MULTIPLE commands are disabled.
5.3 ...Sector Count register with the desired power management level and executes this command, the device sets the BSY bit of the Status register and checks the contents of the Sector Count ...
Manual/User Guide - Page 169
...- The Set transfer mode subcommand in the SET FEATURES command shall be 16.67 million transitions per second or 8.33 MHz (the same as the data. Devices supporting Ultra DMA Mode 2 shall also support Ultra DMA... executing a Power on the cable shall be used for propagation delay, cable settling, and setup time, the sender shall generate a STROBE edge to select the Ultra DMA Mode at any...
Manual/User Guide - Page 230
...Suggestions
Illustration
(
)
Glossary
(
)
Acronyms & Abbreviations (
)
Index
(
)
List any errors or suggestions for improvement. Manual code
C141-E104-03EN
Manual name
MHL2300AT, MHM2200AT, MHM2150AT, MHM2100AT DISK DRIVES PRODUCT MANUAL
Please mark each item: E(Excellent), G(Good), F(Fair), P(Poor). Address: Fujitsu Learning Media Limited 22-7 Minami-Ooi 6-Chome Shinagawa-Ku Tokyo...
Fujitsu MHM2150AT Reviews
We have not received any reviews for Fujitsu yet.