Dymo Rhino 1011 Metal Tape Embosser Support and Manuals
Get Help and Manuals for this Dymo item
View All Support Options Below
Free Dymo Rhino 1011 Metal Tape Embosser manuals!
Problems with Dymo Rhino 1011 Metal Tape Embosser?
Ask a Question
Free Dymo Rhino 1011 Metal Tape Embosser manuals!
Problems with Dymo Rhino 1011 Metal Tape Embosser?
Ask a Question
Popular Dymo Rhino 1011 Metal Tape Embosser Manual Pages
User Guide - Page 2
D
K
M
L
H
I
A
C
F
G
B E
N J
A Tape cassette door B Tape rollers C Tape advance knob D Start line E Tape pawl F Embossing handle G Embossing wheel
H Character selection window I Cutting handle J Embossing adjustment screw K Cable tie slot punch L Hole punch M Cutting assembly N Leader/trailer length guide
2
User Guide - Page 3
DYMO plastic tapes are available in the industry. Metal tapes are used on . This wheel allows you can also use a Reverse Image Wheel with adhesive (35800) • Aluminium without adhesive (31000) • Stainless Steel (32500) You can create a wide variety of colors. Mirror labels are available as follows: • Aluminium with the DYMO M1011 labelmaker. Visit www...
User Guide - Page 4
... your left hand. 2. Insert roll of tape allowing the end to emboss non-adhesive aluminium or plastic tape. Loading the Label Tape
The DYMO M1011 is inserted all the way.
4 Open tape door (A). 3. Squeeze the embossing handle (F) half-way (one click) several
times to ensure the tape is set to extend about 5 cm (2")
through the tape slot. 4. Feed the tape between the two rollers...
User Guide - Page 5
... of the cutting assembly (M) by at least 1 cm (1"). Lift the cutting handle (I
M
Cutting the Tape
To cut the tape.
5
I ) gently until the
tape extends from the front of the cutting assembly so you can easily pull the label out. Squeeze the embossing handle half-way, several times until it is vertical to cut the...
User Guide - Page 6
... in the window (H). 2. Squeeze the embossing handle (F) firmly. 3. To emboss a label 1. To add space between words ‹ Squeeze embossing handle (F) half-way (one click) or turn the
tape advance knob clockwise (one click per space).
6 Release the embossing handle fully before selecting the next
character. F
H G
Embossing the Label
Avoid turning the embossing wheel at the same time...
User Guide - Page 7
...
page 6. When you may need to reverse this adjustment.
7 To adjust for stainless steel tape 1. Turn the adjustment screw (J) clockwise 1/2 to using stainless steel tape. Emboss the text as described in "Embossing the Label" on Stainless Steel Tape
You may need to adjust the labelmaker to emboss properly when using plastic or aluminum tape, you return to 3/4 turn. 2.
User Guide - Page 8
Pull back the pawl (E). 2. Turn the tape advance knob (C) counter-clockwise.
8 To retract the tape 1. E
C
Retracting the Tape
You may want to retract the tape, for example, if the tape advanced too far or to center the text on the label.
User Guide - Page 9
Use caution when removing stainless steel tape that may have sharp edges. 3. A
Removing the Tape
To remove the tape 1. Reload the tape as described in "Loading the Label Tape" on page 8. 2. Open the tape cassette door (A) and remove the tape. Retract the tape as described in "Retracting the Tape" on
page 4.
9
User Guide - Page 10
... on a short label 1. Pull the leader/trailer length guide (N) to cut the tape. Emboss the text on a new label. 2. Lift the cutting handle (I) to the vertical position to the forward position. 3. After cutting the previous label, emboss the text on your label. Retract the tape until the last embossed letter is at start line (D). 2. Use the...
User Guide - Page 11
Apply firm pressure along the entire length to touch the
adhesive. 2. Peel off the protective backing taking care not to ensure good
contact.
11 To apply self-adhesive labels 1. Press the label in place. 3. Applying Self-Adhesive Labels
Self-adhesive plastic and aluminum labels stick permanently to any smooth, clean, and dry surface.
User Guide - Page 12
To punch a hole 1. Insert one end of the cut label into the cable tie slot (K) with the
letters facing down to ensure the ...Make sure to punch a hole. A cable tie slot positioned on the same side of the characters or a punched hole may cause the tape to jam. 2. Insert one or both ends of the cut label into the hole punch slot (L). 2. To punch a cable tie slot 1. You can be ...
User Guide - Page 13
Position the new wheel. 4. To change the wheel 1. Do not tighten the
screw too tightly.
13 Unscrew the screw in the center and tighten. G
Changing the Wheel
You can replace the character wheel with a Reverse Image Wheel. Insert the screw in the center of the embossing wheel (G) and
remove the wheel. 3. Remove the label tape. 2.
User Guide - Page 14
... the labelmaker: • Letters appear where you are probably
squeezing the embossing handle too hard. • Letters overlap - You are squeezing the embossing handle. Hints for Trouble Free Operation
Keep the following in mind when using a soft cloth and alcohol, while turning the tape advance knob back and forth several times. • Avoid turning...
Dymo Rhino 1011 Metal Tape Embosser Reviews
We have not received any reviews for Dymo yet.