Dewalt DWE4597 Support and Manuals
Get Help and Manuals for this Dewalt item
This item is in your list!
View All Support Options Below
Free Dewalt DWE4597 manuals!
Problems with Dewalt DWE4597?
Ask a Question
Free Dewalt DWE4597 manuals!
Problems with Dewalt DWE4597?
Ask a Question
Dewalt DWE4597 Videos
Popular Dewalt DWE4597 Manual Pages
Instruction Manual - Page 3
...corded) power tool or battery-operated (cordless) power tool.
1) WORK AREA SAFETY a) Keep work area clean and well lit. f) If operating a power tool in death ...instruction manual. Read all safety warnings and all instructions. Cluttered or dark areas invite accidents. c) Keep children and bystanders away while operating a power tool. Keep cord away from heat, oil, sharp edges or moving parts...
Instruction Manual - Page 5
... a qualified repair person using only identical replacement parts. Anyone entering the work area. c) The rated speed of the accessory must be within the capacity rating of stopping small abrasive or workpiece fragments. After inspecting and installing an accessory, position yourself and bystanders away from work area must be adequately guarded or controlled. SAFETY INSTRUCTIONS FOR...
Instruction Manual - Page 8
...use , place grinder on cord length ...tool to loss of control.
• Avoid bouncing the wheel or giving it unstable and may result.
• Air vents often cover moving parts...support the workpiece to the brush. Serious injury may result.
• When the gear case grip is properly installed, the use . Holding the work load and centrifugal forces. Additional Safety Rules for Cord Sets...
Instruction Manual - Page 9
...per minute RPM .........revolutions per
minute
minute
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Motor
Be sure your mouth, eyes,...on how often you do this tool does not operate, check power supply.
7 DEWALT tools are NOT safety glasses. Some ... WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer,...
Instruction Manual - Page 10
...this manual:
D28499
9" Angle Grinder
6,000 rpm
DWE4557G
7" Angle Grinder
8,500 rpm
DWE4559NG
9" Angle Grinder
6,500 rpm
DWE4559CNG
9" Angle Grinder
6,500 rpm
DWE4597
7" Angle Grinder
8,500 rpm
DWE4597N
7" Angle Grinder
8,500 rpm
DWE4599N
9" Angle Grinder
6,500 rpm
FIG. 1
K
I .
Trigger switch B. Dust ejection port
INTENDED USE
This grinder is designed for tool-free...
Instruction Manual - Page 11
...set and cannot be shut off ) to restart tool.
FIG. 2
ANTI-VIBRATION SIDE HANDLE (DWE4597, DWE4597N, DWE4599N)
The anti-vibration side handle reduces vibration and user fatigue in the threaded holes.
COMPLETE ELECTRONIC CONTROL™ (DWE4597, DWE4597N...motor from power source before installing and removing accessories, before adjusting or when making repairs. The switch needs to...
Instruction Manual - Page 12
...a DEWALT service center. Before turning the tool on choosing the correct wheel mounting accessories. English
The side handle should be used as the secondary grip surface for this grinder can be
purchased through DEWALT dealers and DEWALT Factory Service
centers.
9"... designed specifically for all other applications.
Overtightening could cause screws to use with flange
D284934
10
Instruction Manual - Page 13
...NOTE: Wheel size must match guard size;
Mounting instructions for accessory guards are shown below and are also...service center. Accessory ratings must always be above tool speed as shown on pages 11-13 of this manual. Use only the accessories shown on
tool...11 flaring cup wheel backing flange
N197992
Type 1 flange set
D284932
7" Type 1 guard
D284931
Grinding backing flange
...
Instruction Manual - Page 16
...guard body should
not be performed with guard
installed on button (C) to ensure that the switch...tool will start -up and during use the tool. B
A
14
Undetectable damage to repair or replace the guard. Cutting can cause injury. To reduce the risk of tool...to maintain control of personal injury, take the tool and guard to a service center to the guard
or the mounting hub may ...
Instruction Manual - Page 17
... nut with available accessory flanges. Lift the tool from rotating when installing or removing wheels.
SPINDLE LOCK BUTTON (FIG. 9)
The spindle lock button (D) is greatest when the tool operates at
high speed.
Apply minimum pressure to the work
surface, allowing the tool to reach full speed before setting the tool down. Depress and hold lock-on...
Instruction Manual - Page 20
...AND WIRE WHEELS 1. Depress spindle lock button and use a wrench on the grinder spindle without moving, or
moving the tool in use of along with a 5/8"-11 threaded hub. USING WIRE CUP ..., allowing the tool to reduce tracking of through regular trash pick-up procedures. Sanding should be changed frequently. 2. Allowing the tool to reach full speed before setting it down.
Plastic...
Instruction Manual - Page 21
Failure to reach full speed before setting it down. Securely tighten the two clamping screws
(U) supplied with
this tool and is required when using the grinder.
Allow the tool to use the proper flange and guard can result in injury resulting from wheel breakage and wheel contact. Allow
the tool to stop rotating before FIG. 19...
Instruction Manual - Page 23
... tool. Use a cloth dampened only with clean, dry air at extra cost from power source before installing and removing accessories, before adjusting or when making repairs. Allow the wheel to bend and may weaken the plastic materials used for your proof of purchase.
21 Always use solvents or other than those offered by a DEWALT factory service center, a DEWALT...
Instruction Manual - Page 24
... you specific legal rights and you are missing, call 1-800-4-DEWALT (1-800433-9258). For products sold in the packaging, call the local company or see website for free, any defects due to normal wear or tool abuse. FREE WARNING LABEL REPLACEMENT: If your product will maintain the tool and replace worn parts caused by our:
1 YEAR FREE SERVICE DEWALT...
Instruction Manual - Page 80
... RPM
DWE4597N 8500 RPM
DWE4557 8500 RPM
DWE4597 8500 RPM
Required Guard
4" Wire Cup Brush
6" Wire Cup Brush
7" Diamond
Cup Wheel
7" Sanding
Flap Disc
7" Sanding
Disc
9" Sanding
Disc
7" Type 1 Diamond or Abrasive Wheel
OPTIMAL
CAPABLE
CANNOT BE USED
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (OCT12) Part No. the "D" shaped air intake...
Dewalt DWE4597 Reviews
Do you have an experience with the Dewalt DWE4597 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dewalt yet.
Earn 750 points for your review!