OpenSwitch OPX Installation Guide with Enhancement Package Release 3.1.0
Page 6
...OPX installation, if an error condition occurs that the system is an existing OS on the switch. If the problem persists, contact Dell EMC Technical Support if you prefer downloading an image over a network. 3 Installation You can install OpenSwitch OPX using an industry-... with auto-discovery, manually, or from a USB device. Installs a new ONIE version. • Embed ONIE - Manually configure your switch or the platform-specific Installation Guide at www.dell.com/support. required serial port settings are 115200, 8 data bits, and no parity. • Connect the Management port ...
...OPX installation, if an error condition occurs that the system is an existing OS on the switch. If the problem persists, contact Dell EMC Technical Support if you prefer downloading an image over a network. 3 Installation You can install OpenSwitch OPX using an industry-... with auto-discovery, manually, or from a USB device. Installs a new ONIE version. • Embed ONIE - Manually configure your switch or the platform-specific Installation Guide at www.dell.com/support. required serial port settings are 115200, 8 data bits, and no parity. • Connect the Management port ...
Networking S6010-ON Getting Started Guide
Page 3
... system, see the following information, available on the Dell Networking Support website (http://www.dell.com/support). • The Dell Networking S6010-ON Installation Guide describes installation and replacement procedures. • The Dell Networking Configuration Guide for the S6010-ON System describes software configuration. • The Dell Networking Command Line Reference Guide for the S6010-ON System provides command line interface (CLI) information...
... system, see the following information, available on the Dell Networking Support website (http://www.dell.com/support). • The Dell Networking S6010-ON Installation Guide describes installation and replacement procedures. • The Dell Networking Configuration Guide for the S6010-ON System describes software configuration. • The Dell Networking Command Line Reference Guide for the S6010-ON System provides command line interface (CLI) information...
Networking S6010-ON Getting Started Guide
Page 23
...8226; Accessing the RJ-45 Console Port with a DB-9 Adapter • Default Configuration • Configuring Layer 2 (Data Link) Mode • Configuring a Host Name • Remote Access to the System • Configuring the Enable Password • Creating a Port-based VLAN • Connect the System ...-party OS, see the documents listed in About this Guide. 3 Configure the Software To initially configure the Dell Networking operating system (OS), use the following sections. If you already have Dell Networking OS 9.x installed on the S6010-ON system, see your system from the factory.
...8226; Accessing the RJ-45 Console Port with a DB-9 Adapter • Default Configuration • Configuring Layer 2 (Data Link) Mode • Configuring a Host Name • Remote Access to the System • Configuring the Enable Password • Creating a Port-based VLAN • Connect the System ...-party OS, see the documents listed in About this Guide. 3 Configure the Software To initially configure the Dell Networking operating system (OS), use the following sections. If you already have Dell Networking OS 9.x installed on the S6010-ON system, see your system from the factory.
Networking S6010-ON Getting Started Guide
Page 26
...the switchport command in INTERFACE mode. Configure the Software 26 Configure the system using the CLI. NOTE: For detailed information about configuring Layer 2, see the Dell Networking Configuration Guide for the default host name, which is Dell). You cannot configure switching or Layer 2 protocols such as...6 3 3 TxD 7 2 4 DTR 8 1 7 RTS Default Configuration When you install the Dell Networking OS onto your S6010-ON system, it is not configured when you power up for the first time (except for the S6010-ON System. INTERFACE mode no shutdown 2 Place the interface in EXEC...
...the switchport command in INTERFACE mode. Configure the Software 26 Configure the system using the CLI. NOTE: For detailed information about configuring Layer 2, see the Dell Networking Configuration Guide for the default host name, which is Dell). You cannot configure switching or Layer 2 protocols such as...6 3 3 TxD 7 2 4 DTR 8 1 7 RTS Default Configuration When you install the Dell Networking OS onto your S6010-ON system, it is not configured when you power up for the first time (except for the S6010-ON System. INTERFACE mode no shutdown 2 Place the interface in EXEC...
Open Networking Hardware Diagnostic Guide December 2021
Page 6
...This tool tests for example, ONIE:/# onie-support/tmp. If a test fails, each diagnostic tool offers a different result. ONIE:/ # onie- Test configuration parameters and test results are saved in CMOS for the open networking (ON) diagnostic (DIAG) operating system (OS). ONIE:/ # dmesg 2. There is...tools finish, your system displays pass or fail test results. for catastrophic hardware failures that prevent booting the system. 2 Overview This guide provides information for the next boot. The error code is no physical alarm indication. For more information, see this README file. ...
...This tool tests for example, ONIE:/# onie-support/tmp. If a test fails, each diagnostic tool offers a different result. ONIE:/ # onie- Test configuration parameters and test results are saved in CMOS for the open networking (ON) diagnostic (DIAG) operating system (OS). ONIE:/ # dmesg 2. There is...tools finish, your system displays pass or fail test results. for catastrophic hardware failures that prevent booting the system. 2 Overview This guide provides information for the next boot. The error code is no physical alarm indication. For more information, see this README file. ...
Open Networking Hardware Diagnostic Guide April 2016
Page 3
Contents 1 About this Guide...7 Notices...7 Related Documents...7 2 Installation Instructions for ONIE and the Dell OS 9 Installing the DIAG-OS...9 Installing ONIE and the DIAG OS 9 ONIE Service Discovery and OS Installation 10 Installing ONIE from the BIOS 11 ...30 Viewing the Dell DIAGs Versions 30 Viewing the CPLD Versions...30 Installing or Upgrading DIAG Tools in the Dell DIAGs OS 31 Restoring the Factory Defaults 31 Restore the Factory Defaults 32 5 Dell DiagOS Tools...33 Diagnostic Tools...33 cpldupgradetool...34 Tests...34 CLI Options...34 Ouput...34 Configuration File Format 35...
Contents 1 About this Guide...7 Notices...7 Related Documents...7 2 Installation Instructions for ONIE and the Dell OS 9 Installing the DIAG-OS...9 Installing ONIE and the DIAG OS 9 ONIE Service Discovery and OS Installation 10 Installing ONIE from the BIOS 11 ...30 Viewing the Dell DIAGs Versions 30 Viewing the CPLD Versions...30 Installing or Upgrading DIAG Tools in the Dell DIAGs OS 31 Restoring the Factory Defaults 31 Restore the Factory Defaults 32 5 Dell DiagOS Tools...33 Diagnostic Tools...33 cpldupgradetool...34 Tests...34 CLI Options...34 Ouput...34 Configuration File Format 35...
Open Networking Hardware Diagnostic Guide April 2016
Page 7
... 1 laser radiation. Related Documents For more information about the Open Networking (-ON) platform, see the following documents. • Dell Command Line Reference Guide • Dell Configuration Guide • Dell Getting Started Guide • Dell Installation Guide About this equipment. Read this guide before servicing. Avoid exposure to a power source. 1 About this equipment. WARNING: Only trained and qualified personnel can install...
... 1 laser radiation. Related Documents For more information about the Open Networking (-ON) platform, see the following documents. • Dell Command Line Reference Guide • Dell Configuration Guide • Dell Getting Started Guide • Dell Installation Guide About this equipment. Read this guide before servicing. Avoid exposure to a power source. 1 About this equipment. WARNING: Only trained and qualified personnel can install...