Brother International XR-9000 Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International XR-9000 manuals!
Problems with Brother International XR-9000?
Ask a Question
Free Brother International XR-9000 manuals!
Problems with Brother International XR-9000?
Ask a Question
Most Recent Brother International XR-9000 Questions
What Foot To Use For Thick Denim?
(Posted by Sunny85392 11 years ago)
Error Code F1
What dose this error code mean.i have taken the needle out and cleaned underneath the needle plate b...
What dose this error code mean.i have taken the needle out and cleaned underneath the needle plate b...
(Posted by Crystalerinfahey 11 years ago)
Cleaning Brother Xr-9000
I know I need to clean my machine but cannot figure out how to get the throat plate off, we have tak...
I know I need to clean my machine but cannot figure out how to get the throat plate off, we have tak...
(Posted by rvolson62 12 years ago)
I Need A New Upper Tension Control Dial.
Hi I need a new upper tension control dial for my brother sewing machine model xl 5500. Where cou...
Hi I need a new upper tension control dial for my brother sewing machine model xl 5500. Where cou...
(Posted by cassie4560 12 years ago)
Popular Brother International XR-9000 Manual Pages
Users Manual - English - Page 1
KNOWING YOUR SEWING MACHINE SEWING BASICS VARIOUS STITCHES APPENDIX
Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs).
Users Manual - English - Page 2
... nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment. Do not use the machine. Always unplug your back or knees. When lifting the sewing machine, be accessed for future reference.
Do not pull on the unit. IMPORTANT SAFETY INSTRUCTIONS
Please read the "IMPORTANT SAFETY INSTRUCTIONS", and then study this manual, or if you are...
Users Manual - English - Page 3
... is required when sewing:
• Always pay close attention is necessary when the machine is used by or near a space heater, iron, halogen lamp, or other parts to assure correct installation.
1 Benzene, thinner, and scouring powders can damage the case and machine, and should be used.
• Always consult the operation manual when replacing or installing any opening...
Users Manual - English - Page 7
...the sewing machine model.
p Presser foot lever (page 17) Used to manually raise and lower the needle. Not for use this to control the sewing speed, and to cut them.
r Handle Carry the sewing machine by its handle when transporting the machine.
5 1 KNOWING YOUR SEWING MACHINE
1
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
The main parts
a Bobbin winder (page 12) This winds the thread onto...
Users Manual - English - Page 8
... bar thread guide. f Feed dogs The feed dogs feed the fabric in the fabric. Operation buttons
The operation buttons help you to start or stop button (for models equipped with the sewing speed controller) Slide the sewing speed controller to set bobbin (for models equipped with the quickset bobbin) You can start /stop button to easily perform various basic sewing machine...
Users Manual - English - Page 10
...We have designed these accessories to carry out most sewing tasks.
Part Name
1 Buttonhole foot "A" 2 Overcasting foot "G" 3 Monogramming foot "N"
Part Code U.S.A. / Canada Others
XC2691-033 XC3098-031 XD0810-031
4 Zipper foot "I"
X59370-021
5 Zigzag foot "J" (on this machine model XR-9000.
● The screw of the presser foot holder is available through your authorized dealer...
Users Manual - English - Page 12
... position changes to start sewing (only for models equipped with the start /stop position
Normally, the sewing machine is placed on the sewing machine. Slower
Faster
You should make sure that nothing is set to select the desired sewing speed.
When you take your foot off the foot controller, the machine will stop position to prevent the machine from accidentally being started...
Users Manual - English - Page 14
.... Pass the end of the bobbin
Turn on the sewing machine. Using other models, the machine will not work properly.
If you use bobbins (part code: SA156, SFB) that comes with this pin. KNOWING YOUR SEWING MACHINE
THREADING THE MACHINE
Winding the bobbin
This section describes how to wind the thread onto the bobbin. • For details on the fast bobbin winding, see page 14.
1 Pulling...
Users Manual - English - Page 15
... wind the thread around the bobbin and cause the needle to fast) (for models equipped with the start/stop button). Cut the thread, slide the bobbin winder shaft k to loosen, and may tangle around
the bobbin a few times.
Slide the sewing speed controller to the right
h (to set the speed to break. Memo
● When the sewing machine is started...
Users Manual - English - Page 16
... the sewing machine is plugged in the bobbin.
a Sewing speed controller
Turn on the sewing machine. a Notch b Bobbin winder shaft spring
Slide the bobbin winder shaft to start /stop button) to start.
Slide the sewing speed controller to the right f (to set the speed to fast) (for models equipped
with the
start/stop button). If the bobbin is cut the thread as described...
Users Manual - English - Page 17
...poorly
● The bobbin was designed specifically for models equipped with your finger, and then pass the
thread through
the tension-adjusting spring of the same type (part code: SA156, SFB).
Install the bobbin wound with this sewing machine.
Raise the needle to the right. CAUTION
● Make sure you accidentally step on quick-set the bobbin so the thread unrolls in the...
Users Manual - English - Page 18
KNOWING YOUR SEWING MACHINE
Replace the bobbin cover. Put the left tab in the diagram).
■ For models equipped with the quick-set the bobbin so the thread unrolls in d place (see arrow a), and then press lightly on
the right side (see arrow b) until the cover clicks into place.
Put the left side of the thread c through the bobbin case is...
Users Manual - English - Page 19
... mark on the wheel points up, or press (needle position button) (for models equipped with the needle position button) once or twice to turn the handwheel so that the
mark on the wheel points up before threading the sewing machine.
17 a Presser foot lever
or
a Mark
b Needle position button
• If the needle is not...
Users Manual - English - Page 20
... hand, then feeding the thread with home sewing machine needles size 75/11100/16. Make sure the main power switch is set incorrectly, the thread may cause sewing problems.
■ Using the needle threader (for the appropriate needle and thread combinations.
Lower the presser foot lever. The thread can only be passed behind the needle bar thread f guide above the needle. Make...
Users Manual - English - Page 74
... machine. sew.
Replace the needle plate.
Only use a bobbin that is not appropriate for example, in the presser foot is tangled, for the Choose a needle that has been designed for the type of stitch that you want to
you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. The needle is appropriate
thread...
Brother International XR-9000 Reviews
We have not received any reviews for Brother International yet.