Brother International XR-9000 Support Question
Brother International XR-9000 Support Question
Find answers below for this question about Brother International XR-9000.Need a Brother International XR-9000 manual? We have 3 online manuals for this item!
Question posted by cassie4560 on March 30th, 2012
I Need A New Upper Tension Control Dial.
Hi I need a new upper tension control dial for my brother sewing machine model xl 5500. Where could I find it online and how much does it cost? I'd like to start sewing again asap. Thank you.
Current Answers
Related Brother International XR-9000 Manual Pages
Users Manual - English - Page 2
... cord. INTRODUCTION
Thank you notice anything unusual, such as an odor, heat, discoloration or deformation, stop using the machine immediately and unplug the power cord. Before using this machine, carefully read these safety instructions before attempting to persons.
2 Always unplug the machine from the electrical outlet immediately after you have finished reading this sewing machine.
Users Manual - English - Page 3
... or disposed of suffocation. • Do not use outdoors.
7 For a longer service life:
• When storing this sewing machine was supplied in fire or an electric shock. • Do not place this sewing machine on the foot controller. • Do not use bent or damaged needles. • Keep fingers away from all moving parts. Plug...
Users Manual - English - Page 5
...
USING YOUR SEWING MACHINE 9
Power supply precautions ...9 Turning on the machine ...9 Foot controller ...10 Sewing speed controller (for models equipped with the sewing speed controller 10 Changing the needle stop position ...10 Changing the initial needle position ...11 Cancelling the operation beep ...11
THREADING THE MACHINE 12
Winding the bobbin ...12 Lower threading ...15 Upper threading...
Users Manual - English - Page 7
... the spool of the upper thread. d Upper tension-control dial (page 31) This controls the tension of thread. o Feed dog position lever (pages 49 and 56) Use the feed dog position lever to manually raise and lower the needle. q Foot controller (page 10) You can turn the main power and sewing light switch on the sewing machine model. p Presser foot lever (page...
Users Manual - English - Page 8
...for models equipped with the sewing speed controller) Slide the sewing speed controller to easily perform various basic sewing machine operations.
d Needle position button (for sewing straight seams.
j Needle bar thread guide Pass the upper thread through the needle bar thread guide. e Sewing speed controller (for models equipped with the start/stop button) Press the start/stop sewing...
Users Manual - English - Page 10
... XC3098-031 XD0810-031
4 Zipper foot "I"
X59370-021
5 Zigzag foot "J" (on this machine model XR-9000.
● The screw of the presser foot holder is available through your authorized dealer. (...SEWING MACHINE
ACCESSORIES
The following accessories are stored in the flat bed attachment. only) ● Foot controller: Model T
This foot controller can be able to help you be used on machine...
Users Manual - English - Page 12
... models equipped with the start sewing (only for models equipped with the sewing speed controller)
Slide the sewing speed controller to the left or a right to sew at a faster speed. a Foot controller jack/socket
CAUTION
● When connecting the foot controller, be sure to turn on the left to sew at a low speed. When you take your foot off the foot controller, the machine...
Users Manual - English - Page 14
... have been designed for this machine or bobbins of the bobbin.
Pass the thread around the pre-tension disk. Put the bobbin onto the bobbin winder shaft d and slide the bobbin winder shaft to wind the thread onto the bobbin. • For details on the sewing machine.
Using other models, the machine will not work properly.
Users Manual - English - Page 15
... started or the handwheel is not a malfunction.
● The needle bar does not move when you follow the instructions carefully. CAUTION
● Not winding the bobbin properly may cause the thread tension to the right. Then stop the machine.
1
Note
● If the sewing machine is to its l original position (for models equipped with the sewing speed controller...
Users Manual - English - Page 16
... start / h stop button) to wind the free end of the procedure in the bobbin.
g
Press the foot controller or press (start .
Place the bobbin on the sewing machine.
Pull the thread to the right and pass it through 2 of the thread clockwise around the d pre-tension disk with the
start/stop button) (for models equipped with the sewing speed controller...
Users Manual - English - Page 17
... direction. CAUTION
● Make sure you slide the bobbin winding shaft to sew, you (counterclockwise) or
press (needle position button) (for this machine.
If bobbins from other models are used with thread. • For more details on the foot controller and the machine starts to the right. CAUTION
● Make sure you accidentally step on quick...
Users Manual - English - Page 18
... position button) (for models equipped with this machine. Put the left side of the thread c through the slit, and then pull the thread to cut it may cause the thread tension to be incorrect or break the needle.
1
a Cutter
16
Replace the bobbin cover. CAUTION
● Make sure you start to sew, follow the procedure...
Users Manual - English - Page 19
... the handwheel
CAUTION
● Make sure you thread the machine properly. Upper threading
Set the upper thread and thread the needle. • For details on the needle threader, see page 18.
1
a Spool pin b Thread guide c Mark on the wheel points up before threading the sewing machine.
17
a Presser foot lever
or
a Mark
b Needle position button...
Users Manual - English - Page 20
... use needles in the range of the procedure in a "Upper threading" to thread the machine to left hand, then feeding the thread with home sewing machine needles size 75/11100/16. Lower the presser foot lever.... inch) of the needle by holding the thread in the figure
d on page 21 for models equipped with the needle threader)
CAUTION
● The needle threader can only be used with your...
Users Manual - English - Page 22
... foot.
Pass the thread along the slit in b steps 1 to draw up the lower c thread.
a Upper thread b Lower thread
a Upper thread b Lower thread
■ For models equipped with the needle position button) once or twice.
KNOWING YOUR SEWING MACHINE
Drawing up the bobbin thread.
or
a Mark
b Needle position button
Pull on the wheel points up...
Users Manual - English - Page 33
... e Loops appear on
surface of fabric
Solution Reduce the tension by turning the upper tension-control dial to adjust it when you start to a lower number.
54 3
Note
● If the upper thread was incorrectly threaded, the upper thread may need to a higher number.
54 3
31 Adjusting thread tension
The thread tension will appear on the surface of the fabric.
■...
Users Manual - English - Page 74
...The upper thread tension is...brother.com]. Symptom The sewing machine does not work properly. sew.
Only use a bobbin that has been designed for example, you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips.
You have not used the foot controller properly.
The area around the hole in .
The needle is scratched.
The upper...
Users Manual - English - Page 76
...22
The presser foot that has been designed for this machine. The thread tension is incorrect. If the thread is correct for
not ...machine. Lengthen the stitch length.
You have not used .
The bobbin case is bent or blunt.
Slide the feed dog position lever to sew. page 21 page 70
The sewing light bulb does not The sewing lamp is incorrect. Adjust the tension of the upper...
Users Manual - English - Page 78
... attachment 7, 34 foot controller 8, 30
free-arm style...tension disk 12
Q
quick-set bobbin 6, 16
quilting 55 quilting foot 56 quilting guide 55
R
reinforcement stitching 57 reverse/reinforcement stitch button 6
S
scallop stitching 61 seam ripper 48 sewing machine needles 21 sewing speed controller 6 sewing the character stitches 67 sleeve holes 57 smocking 61
spool pin 12, 17 start...
Users Manual - English - Page 79
T
thick fabrics 32 thin fabrics 34 thread cutter 30 thread guide 17 thread tension 31 trial sewing 32 triple stretch stitch 43 troubleshooting 72 twin needle 24
U
upper tension-control dial 31 upper threading 17
utility stitch indicator 7, 28 utility stitch key 7, 28
W
walking foot 55 wing needle 63
Z
zigzag stitch 32, 42, 53
4
zipper foot 51
zipper Insertion 51
77
Similar Questions
Problem With Control Box Brother Md 741 B
Hiproblem With Control Box Brother Md 741 Berror Code On Control Box Indicate guneed Helpthanks
Hiproblem With Control Box Brother Md 741 Berror Code On Control Box Indicate guneed Helpthanks
(Posted by ytechanrow 9 years ago)
How To Adjust The Upper Tension On A Brother Pe770
(Posted by SFTcca 9 years ago)
How To Set The Tension On A Brother Ls2300prw Sewing Machine
(Posted by bondha 10 years ago)
Brother Sewing Machine Model Xl-3510. How To Thread The Bobbin?
I put the bobbin in according to the manual, but when I start sewing, it does not work. The user man...
I put the bobbin in according to the manual, but when I start sewing, it does not work. The user man...
(Posted by msa1234 11 years ago)
Cleaning Brother Xr-9000
I know I need to clean my machine but cannot figure out how to get the throat plate off, we have tak...
I know I need to clean my machine but cannot figure out how to get the throat plate off, we have tak...
(Posted by rvolson62 11 years ago)