Acer VG242YP Support and Manuals
Get Help and Manuals for this Acer Computers item
View All Support Options Below
Free Acer VG242YP manuals!
Problems with Acer VG242YP?
Ask a Question
Free Acer VG242YP manuals!
Problems with Acer VG242YP?
Ask a Question
Popular Acer VG242YP Manual Pages
User Manual - Page 2
... and specifically disclaims the implied warranties of this publication may be reproduced, stored in a retrieval system, or transmitted, in the space provided below. No part of this manual or supplementary documents and publications. Other companies' product names or trademarks are used herein for a particular purpose. All Rights Reserved. Acer LCD Monitor User Guide
Model number...
User Manual - Page 5
...the plug into the product • the product was exposed to replace the power cord set . Contact your electrician for service • the product does not operate normally after following requirements: ...devices.
Also, make sure that the new power cord meets the following the operating instructions
v If you to dangerous voltage points or other nearby electrical devices that may ...
User Manual - Page 15
...8226; For units using 120 V AC: Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
• For units using 220/240 V AC: Use a cord set should have the appropriate safety approvals for your area.
• The... first to make sure that allows operation in which the equipment will be installed. The cord set consisting of the AC power cord to ON state is around 3 seconds.
4
User Manual - Page 16
for certain models
PIN No. 11 12 13 14 15 16 17 18 19
Description TMDS ...
TMDS data 0 shield
9
TMDS data 0-
10
TMDS clock+
* only for example, supported resolutions and corresponding timing. Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol, the monitor is a communication protocol through which the monitor automatically informs the ...
User Manual - Page 17
20-pin color display signal cable
PIN No. 1 2 3 4 5 6 7 8 9 10
Description Lane0 (p) GND Lane0 (n) Lane1 (p) GND Lane1 (n) Lane2 (p) GND Lane3 (n) Lane3 (p)
* only for certain models
PIN No. 11 12 13 14 15 16 17 18 19 20
Description GND
Lane3 (n) Config1 Config2 AUX_CH (n)
GND AUX_CH (p) Hot Plug Detect DP Power_Return
DP Power
6
User Manual - Page 18
...
165*
Hz
* VG242Y can be overclocked to a higher refresh rate than advertised by the panel specification.This function can be use the system control panel to support refresh rate overclocking. Important: This device is designed to set the maximum refresh rate. If you experience instability, try reducing the overclock to a lower refresh rate...
User Manual - Page 19
...for more instruction.
8 Please check user manual for audio output model. Connect the HDMI Cable (Only HDMI-Input Model)
(1) ...Make sure both the monitor and computer are switched off. (2) Connect one end of the 20-pin DP cable to the back of the monitor and the other end to the computer's port. Installation...
User Manual - Page 20
... to view the
basic information for your monitor and current input or reset
the custom color settings to dynamically adjust display refresh rate based on . User Controls
1 2 3 4 5... power on typical content frame rates for power efficient, virtually stutter free and low-latency display update.
9
Amber indicates standby/power saving mode.
2
Function key a. Press to view Main page...
User Manual - Page 21
... G3) which user-defined profile to use the OSD to adjust the picture quality, OSD position and general settings. When you are done, press the joystick to open the OSD. The OSD (onscreen display) can use.../Gamma/Contrast/ Blue Light/Over Drive/PIP/PBP/VRB
2. Actual product specifications may vary. Using the Shortcut Menu
Note: The following page:
Main page
Mode Standard
Brightness 70
Input...
User Manual - Page 22
Input
Input
HDMI 2(2.0)
Auto Source
On
Move
The Function page
Open the Function page to adjust the functions, settings which you wish to adjust and press the joystick to enter it.
3. When you are done, toggle the joystick to the left or right to ...
User Manual - Page 24
...
HDR = (Auto, HDR-400 or Off,) • HDR Status:
Information
Main Source HDMI Resolution 1920x1080 H/V Frequency H: 56 KHz V: 60 Hz Mode SDR S/N :MMTL7EE003014000013E00
Reset All Settings Exit
Move
Exit
Information Page
Optional Auto
HDR-400 Off (Default)
Behavior Auto checked input source status Display HDR-400 Standard and Effect. • HDR...
User Manual - Page 26
...Drive: Select Off, Normal, or Extreme. 5. If FreeSync Premium is "OFF", then the user can set to "Normal"
automatically. 2. Volume: Adjust the volume 5. Gaming
Mode - Toggle to the left ... three settings including: (a) Extreme (b) Normal (c) Off.
15 Press the MENU key to adjust the sliding scales. 4. FreeSync Premium: To control support FreeSync Premium or not, default is set Over ...
User Manual - Page 27
... the processing time of the display switching process. Refresh rate num: Display the panel's current refresh rate on the screen for shooting games. Note: 1. VRB set VRB is not supported at resolutions below 800 x 600. 9. Ultra-low latency is "Off" 7. Aim point: Show an Aim point on the screen. 6. Ultra-Low Latency...
User Manual - Page 29
... Toggle to the left or right to open the OSD.
2. Note: Surround application must set Auto Source is DP1.2, can support auto search for signal source in order. Standard
Picture Color Audio Gaming OSD System
Quick Start... and 1:1.
8.
Wide mode: You can select which can selection support DP1.1, or DP1.2 format.
7. Then toggle to the right to navigate to select System from HDMI1, HDMI2, ...
User Manual - Page 31
... cable is On, the LED status set Amber. Note: Acer monitor is switched on and in power saving/standby mode.
Check if the computer system is purposed for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. DP/HDMI Mode (Optional)
Problem No picture visible
LED status Blue...
Acer VG242YP Reviews
We have not received any reviews for Acer yet.