Yamaha AW16G Support Question
Yamaha AW16G Support Question
Find answers below for this question about Yamaha AW16G.Need a Yamaha AW16G manual? We have 1 online manual for this item!
Question posted by jboy1953 on September 24th, 2012
Where Can I Purchase A Replacement 'record Button' Red Plastic Part Aw16
The plastic (red and white) piece that sits on top of the "record" switch on my AW16 broke and I need a new piece, is it possible to order this?
Current Answers
Related Yamaha AW16G Manual Pages
Owner's Manual - Page 20
...AW16G
■ Data entry/control section
1 4
2
3
5
6
1 [UNDO/REDO] key This key cancels the results of a parameter.
C [REPEAT] key This key switches...Use this key to operate a button displayed in the screen, or to change the value of a recording or track editing operation (Undo),...if Undo can record or play a specified region.
B [AUTO PUNCH] key This key switches the audio punch-in ...
Owner's Manual - Page 23
... 1-4
Operating the knobs or keys of the Selected Channel section will be displayed in white with white text. The following types of the channel that was last used in the display are calculated according to switch a parameter on the AW16G. The name of measures/beats. D Counter (right side) This indicates the current location within...
Owner's Manual - Page 27
...audio sources or effect processors connected to the input/output jacks of the AW16G
B The AW16G itself
C The monitor system connected to the output jacks of the AW16G
When you turn on the power switch of connections to the AW16G....
After the opening screen, the following order.
This chapter explains how to the demo song
When the AW16G is shipped from the factory, its hard...
Owner's Manual - Page 34
...bus assign switch When you move more widely. (However, you will not yet hear anything from your monitor system.)
For the best audio quality, adjust the level as high as possible without change to the recorder and ... you press and hold an [INPUT SEL] key, the INPUT SETTING popup window will leave this button and press the [ENTER] key to close the popup window and return to the previous screen....
Owner's Manual - Page 37
...button, and press the [ENTER] key. When you exit the CLIP screen, you will be overwritten. Tip!
• A popup window will play back the previously recorded content or record a new performance.
Stops playback, recording... sound clip. You will begin. If you hold down this returns to an audio track of the Recorder section by using the EDIT screen COPY command (→ p. 128).
5 To...
Owner's Manual - Page 39
...; p. 24).
6 To create the new song, move the cursor to the AW16G onto the first track of the following items if desired.
SCENE button Scene memories LIBRARY button.........
EQ, dynamics, effects, and channel
libraries TEMPO button Tempo map
39 Chapter 5
Track recording
This chapter explains how to create a new song, and record the audio signal from an instrument...
Owner's Manual - Page 42
... channel. To exit this window and return to the previous screen, move the cursor to this button and press the [ENTER] key, all [TRACK SEL] keys will blink red.
If you press and hold down the [RECORD] key and use the CURSOR [ ]/[ ] keys to tracks 1-8. The screen will indicate how input channels are...
Owner's Manual - Page 43
...red, and then press the [TRACK SEL] key of the track that is selected as the recording destination. To cancel all connections, move the cursor to the SAFE button and press the [ENTER] key.
• To change the recording...and the level knob).
You can switch the location at for the recording-destination track is recorded, but rather the signal after recording.
43 In the screen, a ...
Owner's Manual - Page 48
.../JOG] dial to tracks will be cancelled. It will no longer be possible to press the [REC] key, and this will prevent recording from the beginning, press the RTZ [ ] key to return the counter... recording, press the [UNDO/REDO] key.
This indicates that you can select 1-16 (audio track 1-16), ST (stereo track), or PAD 1-4 (pad track 1-4).
F NAME button When you move the cursor to be recorded....
Owner's Manual - Page 49
...3 To defeat pairing, hold down the [INPUT SEL] key (or [TRACK SEL] key) of one of the following buttons and press the [ENTER] key. Tip! INPUT (TRACK) x → y (x= odd number, y= even number)........ ... are recording a stereo audio source, or when you want to play back two bus-recorded tracks as well. However, you decide not to cancel pairing, move the cursor to the CANCEL button and press...
Owner's Manual - Page 56
... the input signal to a track
In order to overdub, you turn the [EQ] knob to left or right while pressing it . Tip! However, you may also use "bus recording," in which you can instantly recall an..., refer to a new track.
When you must first assign the mic or instrument to "Track recording" (→ p. 39). The [INPUT SEL] key and [TRACK SEL] key will blink red.
4 Assign the input...
Owner's Manual - Page 65
...order to absolute time 00:00:00.000.
If you select REL as the counter display format, the current location will be written to specify the region of the recording... an audio CD, the Start and End points can be used to the audio CD ...AW16G. When you press the RTZ [ ] key in the transport section, you create a new..." (move back. On the AW16G, you record past the previously-set End point...
Owner's Manual - Page 86
... to cancel record-ready mode.
If you to confirm that is used to create an audio CD.
This setting is shared with the BUS page of the stereo track.
6 Switch the ST.TRACK ON/OFF button ON.
Then... page, and press the [ENTER] key to turn the button on.
C Track view In this button is on, the stereo track output will blink red. The panel [STEREO] key will be sent to a point...
Owner's Manual - Page 87
...bouncedestination assignments will be "flat the center position. If you select an unpaired track, the pan of the RECORD screen. E BUS button When you select track 1, 3, 5, or 7, bus L will be turned off status of the L/R bus,...selected bounce-destination track(s). The [TRACK SEL] key will blink red, indicates that the corresponding track is selected as the bouncedestination.
Owner's Manual - Page 105
..., you turn on the PERFECTLY button
10
Creating an audio CD
105 Move the cursor to confirm the erasure. ● If you turn on the SIMPLY button
● If you do not need to perform this operation on the AW16G. A popup window will ask you selected the OK button, erasure will begin. (This operation...
Owner's Manual - Page 111
...] key and use this will play if you can switch muting on/off for each track. If a pad track is muted and the pad is displayed the name of the sample assigned to the audio tracks play back the recorder.
Move the cursor to this button and press the [ENTER] key to (muted). At...
Owner's Manual - Page 145
... 1
2 3
4 Move the cursor to the TRACK field and V.TR field, and turn this button on, you will return to access the BACKUP page. When the track has been imported, you will appear.
3 ... (●) will be able to the OK button and press the [ENTER] key. Backing up songs and sample libraries
Here's how you can back up the audio tracks within a song in the list will ...
Owner's Manual - Page 146
... OK button and press the [ENTER] key. Remove the media, and replace it was saved.
5 To execute the backup, move the cursor to the OK button and ...button and press the [ENTER] key, and the media will be erased.
• If a CD-ROM or previously-recorded CD-R media is OK to back up . Be sure to the ● symbol, indicating that this step to step 3. The symbol for backup.
Insert a new...
Owner's Manual - Page 160
... signal from the DIGITAL IN jack will appear. If a problem is possible that is always set to STEREO BUS. It is found , a ...switch the DIGITAL IN PATCH setting to DISABLE.
However when playing an audio CD, the AW16G always operates using its own clock. B ATT knob Adjusts the level of the signal that the hard disk has been physically damaged.
160
The DIGITAL REC ON/OFF button...
Owner's Manual - Page 163
... and MTC slave, and set its owner's manual.
4 In the MIDI OUT field, turn on the MIDI button and MTC button. Tip! In this case, refer to the section that follows, "Recording/playing AW16G mix operations on how to make these settings, refer to the manual for synchronization using MTC and MMC. Tip!
Similar Questions
Battery Replacement
How do I replace the battery in my aw2816 Yamaha workstation
How do I replace the battery in my aw2816 Yamaha workstation
(Posted by mrnat12 5 years ago)
Multi Jog / Digital Rec Level Knob/button
I need to obtain a multi jog knob/button for this model.Can anyone provide me with a part number or ...
I need to obtain a multi jog knob/button for this model.Can anyone provide me with a part number or ...
(Posted by mikebongard 9 years ago)
