Weider Club 4870 Support Question
Weider Club 4870 Support Question
Find answers below for this question about Weider Club 4870.Need a Weider Club 4870 manual? We have 1 online manual for this item!
Question posted by babyslife30 on July 16th, 2019
Cable Is Off Track And I Can't Push The Pin In The Weights
I'm trying to work out but I pulled the bar down too far and I think the cable has slipped. How do I fix it?
Current Answers
Answer #1: Posted by Troubleshooter101 on July 28th, 2019 8:00 AM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,040
Member since:
September 30th, 2015 Points: 2,927,040
You can check the product manual Please Click below:
https://www.manualslib.com/manual/189421/Weider-Club-4870-Wesy3906-0.html
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related Weider Club 4870 Manual Pages
English Manual - Page 2
... missing or illegible, call the toll-free telephone number on the weight system. Apply the decal in the location shown. TABLE OF CONTENTS
WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 PART IDENTIFICATION CHART 5 ASSEMBLY 7 ADJUSTMENTS 25 CABLE DIAGRAM 28 EXERCISE GUIDELINES 29 PART LIST 32 EXPLODED DRAWING 33 ORDERING REPLACEMENT PARTS Back...
English Manual - Page 3
... does not use the weight system. Do not use the weight system with the lock pin and lock after exercising to mount, dismount, and use the lat bar.
5. Replace any time while exercising, stop immediately and make sure that the cables remain on the weight system before using the weight system. Make sure that the cables are adequately informed of...
English Manual - Page 4
...labeled. To avoid a registration fee for selecting the versatile WEIDER® Club 4870 weight system. Before reading further, please review the drawing below and familiarize yourself with the parts ... Butterfly Arm
Backrest Curl Pad Leg Lever
Right Side
Left Side
High Pulley Station Lat Bar
Military Press Arm Adjustable Backrest
Press Arm Seat
Leg Press
Low Pulley Station
12.5-lb...
English Manual - Page 7
... it takes to read the information on pages 5 and 6 to identify the small parts used .
How to the weights. Place all parts are found in the drawings.
This brief introduction will attach the cables and pulleys that stage. Hire an Authorized Service Technician
To hire an authorized service technician to make assembly...
English Manual - Page 11
... (5) in step 2.
89 12
7
30
30
Hole
66 84 108
68
5
108
87
11
Attach the Weight Guide to the Center Upright (9) with two M10 x 35mm Screws (89).
Attach the Left Top Frame (4) to...Bolts (87) and
an M10 Nylon Locknut (84). Attach the Butterfly Frame (24) to the bottom. Orient a Weight Guide (30) with two M10 x 90mm Bolts (102) and two M10 Nylon Locknuts (84).
Do not tighten...
English Manual - Page 12
... (63) and insert the Bushing into the stack of 12.5-lb. Insert the Weight Tube into the Leg Lever (15). Orient a Weight Tube (75) as shown. Weight (34) onto the Weight Guides (30).
34
30 30
75
34
Pin Groove
14.
Weights (34). Slide another 12.5-lb. Slide eleven 12.5-lb. Do not tighten the Bolts...
English Manual - Page 15
the Leg
Press Plate must be able to an M10 x 75mm Bolt (96). Make sure that the Cable end can pivot easily around a Pulley
26
(43). Make sure that the Cable Trap is oriented to the Left Butterfly Arm (22) with an M10 x 120mm Bolt (97),
an M10 Washer, and an M10 Nylon...
English Manual - Page 16
... (49) with an M10 x 150mm
Bolt (94) and an M10 Nylon Locknut (84). Make sure that the Cable Trap is oriented to the Right Butterfly Arm (23) with
an M10 x 40mm Bolt (104) and an M10 ...Half Guards are oriented as shown.
16
84 48 73
46
46
105 49 43
49 Attach the "V"-pulley, a Long Cable Trap
(83), an M10 Washer (108), and two Guards (45)
to the Right Top Frame (3) with an M10 x...
English Manual - Page 17
... Bolt (105) and an M10 Nylon
Locknut (84).
73 84
67 75
105
34. Attach the Butterfly Cable (73) and a Weight Cap
33
(67) to the Center Top Frame (6)
with
an M10 x 45mm Bolt (95) and an... M10 Nylon
Locknut (84).
84 3
73 95
43
32. Wrap the Butterfly Cable (73) over a Pulley (43).
32
Attach the Pulley to the indicated Weight Tube (75) with an M10 x 45mm Bolt (95) and an M10 Nylon...
English Manual - Page 18
...
18 Make sure the Half Guards
are oriented as shown.
37. Wrap the Low Cable (70) over a Pulley (43).
37
Attach the Pulley, a Cable Trap (48), and two Half
Guards (46) at the second hole from the... bottom
of the Pulley. 35. Make
sure that the Cable Trap is oriented to the Right Base
(1) with an M10 x 45mm Bolt (95) and an M10
Nylon...
English Manual - Page 21
...the inset drawing. it
should be tightened so that the Cable Trap is oriented to hold the Cable in
the groove of the Pulley. Attach the Pulley, a Cable Trap (48), an M10 Washer (108), and two... M10 x 130mm Bolt (106)
and an M10 Nylon Locknut (84). Wrap the Press Cable (72) under a Pulley (43).
47
Attach the Pulley, a Cable Trap (48), an M10
Washer (108), and two Half Guards (46) to the
...
English Manual - Page 24
... not move smoothly over the pulleys. If one of the remaining parts will need to remove the slack by tightening the cables (see page 27).
24 Before using the weight system, pull each cable a few times to the Curl Post (16) with
58
two M6 x 16mm Screws (99).
38
16 99
59. IMPORTANT: If...
English Manual - Page 25
... on page 27).
70 81
82 74 81
25 Insert the Weight Pin so that the Lat Bar is used. For some exercises, the Chain (82) should be attached to the Low Cable (70) with a Weight Clip (81). When using the low pulley station, always engage the Leg Lever Lock (47 see the correct form for...
English Manual - Page 26
...the Curl Pad (38) from the weight system when performing an exercise that does not require it at the... desired height with an Adjustment Knob (69). Next, move the Backrest to the desired position. Next, move the Seat to remove the Adjustment Knob.
38 16
37 69
LOCKING THE WEIGHT STACK Lock the weight stack by inserting a Lock Pin (78) through a Weight...
English Manual - Page 27
... Lock (47) onto the Leg Lever (15) tube.
If there is slack in the cables before resistance is felt, the cables should be removed from these cables in several ways:
See drawing A. To tighten the cables, first insert the weight pin into the middle of the
Pulley, that the Half Guards are oriented as
shown, and...
English Manual - Page 28
... diagrams to make sure that the cable traps do not touch or bind the cables.
5 Butterfly Cable (73)
Length: 10' 2"
6
8
9
4
10 8
3
7
1
2
11
6
9
10 6 7 4
Low Cable (70) Length: 27' 8"
2 1
5 3
Press Cable (72) Length: 11' 2"
2 4 5
1 3
28 Make sure that the cables, the cable traps, and the guards have not been correctly routed, the weight system will not function properly and...
English Manual - Page 29
...WORKING OUT
Each workout should be sensitive to regenerate. This requires moving only the appropriate parts of motion for you can complete 3 sets of 12 repetitions without difficulty, increase the amount of weight. You can tone your muscles by pushing... fitness program. Weight Loss To lose weight, use a low amount of weight and increase the number of 8 repetitions for each exercise ...
English Manual - Page 30
...exercise. List the date, the exercises performed, the resistance used, and the numbers of thigh) J. Record your weight...each stretch gradually and go only as far as you can without strain. Pectoralis ...a muscle
building workout. • Rest for one minute after each set for a toning work- Quadriceps (front of calf) K.
Abductor (outer thigh) H. Tibialis Anterior (front of ...
English Manual - Page 32
...12 2" Round Inner Cap 92 2 M8 x 25mm Shoulder
56 4 1 1/2" Round Inner
Bolt
Cap
93 1 Weight Pin
57 23 M10 x 70mm Bolt
94 1 M10 x 150mm Bolt
58 4 3/4" Round Inner Cap 95 8 ... Cable
107 1 M10 x 95mm Bolt
71 2 3" Bushing
108 44 M10 Washer
72 1 Press Cable
# 1 User's Manual
73 1 Butterfly Cable
# 1 Exercise Guide
74 1 Lat Bar
# 2 Hex Key
75 1 Weight Tube
# 2 Grease Pack
76 1 Weight ...
English Manual - Page 36
...fitness for a particular purpose is limited in connection with the use or performance of the product or damages with respect to be prepared to give the following information: • the MODEL NUMBER of the product (WESY3906.1) • the NAME of the product (WEIDER CLUB 4870 weight... on how long an implied warranty lasts. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
...
Similar Questions
Weights Sticking
on the triceps tower side with only the top weight the cables go slack and the weight is slow to dro...
on the triceps tower side with only the top weight the cables go slack and the weight is slow to dro...
(Posted by kaldous 3 years ago)
Where Do I Get New Cables
i need new cables for weider club 4870 model wesy3906.1
i need new cables for weider club 4870 model wesy3906.1
(Posted by smoreland1658 4 years ago)
Weight Pin
why we were moving the equipment we lost the PIN to the weights. Is there a replacement we can get a...
why we were moving the equipment we lost the PIN to the weights. Is there a replacement we can get a...
(Posted by robdaddy1964 7 years ago)