TP-Link TL-SL2428WEB Support Question
TP-Link TL-SL2428WEB Support Question
Find answers below for this question about TP-Link TL-SL2428WEB.Need a TP-Link TL-SL2428WEB manual? We have 1 online manual for this item!
Question posted by alexandervegagomero on September 20th, 2020
How To Reset Tp-link Tl-sl2428web
The person who posted this question about this TP-Link product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Troubleshooter101 on September 20th, 2020 9:51 PM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,060
Member since:
September 30th, 2015 Points: 2,927,060
Note: Hard reset will remove all your settings, and your device will be restored to factory default settings. Do not perform a hard reset unless you have backed up your settings or you can do the configuration again.
Step1
Turn off the switch (pull the power out of the device).
Step2
Press and hold the reset button on the front panel with a pin, while holding down the reset button turn on the switch (plug the power back into the device), please keep on holding down the reset button for approximately 10 seconds.
Step3
Release the reset button and wait for the device to reboot.
Note:
1.After the hard reset, the IP address of the device should be changed to the default 192.168.0.1, and the default login username and password are both supervisor (all lower case).
2. Ensure that the IP address of your computer is in the same IP range with the device. That means your computer should have an IP address like 192.168.0.X(X is in range of 2~253), and the subnet mask is 255.255.255.0.
Please check this user manual for reference:-
https://www.manualslib.com/products/Tp-Link-Tl-Sl2428web-3455638.html
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related TP-Link TL-SL2428WEB Manual Pages
User Guide - Page 2
... by any means or used in any form or by one or more of TP-LINK Technologies Co., Ltd. If this equipment does cause harmful interference to radio or ...the equipment and receiver. Connect the equipment into an outlet on a circuit different from TP-LINK Technologies Co., Ltd. COPYRIGHT & TRADEMARKS
Specifications are subject to change without permission from that interference...
User Guide - Page 9
... the TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/ TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family! Provides an overview about the switch family. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Chapter 1: Introduction
Thanks for configuring, and managing the TP-Link device:
Section 1: Introduction. The switch family...
User Guide - Page 13
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Transmission Medium
LED
Dimensions (L×W×... Link/Act and 10/100/1000Mbps LED SFP port: 1000Mbps Link/Act LED 294mm×180mm×44mm (TL-SG2109WEB/TL-SL2210WEB) 440mm×180mm×44mm (TL-SL2218WEB) 440mm×180mm×44mm (TL-SL2428WEB) 440mm×260mm×44mm (TL-...
User Guide - Page 14
...Li nk /A c t
8+2G 1
Web-Smart 2
Switch
3
1000M
4 5
GIGA
RESET
6 7 8
GIGA
10/100 Mbp s
SFP
10/100/1000Mbps
1000Mbps
Link/Act
Figure 3-1 Mounting Brackets
Ensure the device is placed in a wiring closet with other equipment.
1. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Chapter 3: Mounting Device
3.1 Install...
User Guide - Page 15
... 3.2.1 Front Panel
The front panel of 10M, 100M or 1000M. The switch's power supply will adjust to factory default setting.
LEDS
Insert the switch into the rack. 3. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
2. It has a corresponding Link/Act and 10/100/1000Mbps LED.
1 SFP ports: designed to...
User Guide - Page 16
...-SL2218WEB
16+2G Gigabit Web-Smart Switch
Power System
Link
1 3 5 7 9 11 13 15
Act
100Mbps
RESET
Link/Act
2 4 6 8 10 12 14 16
GIGA
1000Mbps
1
3
5
7
2
4
6
8
9
11
13
15
10
12
14
16
GIGA
SFP
Link/Act
Figure 3-4 TL-SL2218WEB Front Panel
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
1) LEDs lie at the left...
User Guide - Page 17
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
R
1
3
5
7
TL-SL2428WEB 24+4G Gigabit Web-Smart Switch
Power
Link
1 3 5 7 9 11 13 15 17 19 21 23
Act
100Mbps
System
2 4 6 8 10 12 14 16 18 20 22 24
RESET Link/Act GIGA1 GIGA2 1000Mbps
2
4
6
8
9
11
13
15
10
12
14
16
17
19
21
23
18
20...
User Guide - Page 19
...
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TLSL2452WEB Web-Smart Switch Family is dedicated to default except the switch IP address.
12 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Chapter 4: Function Description
This section presents the network concepts referred in TFTP protocol. Soft-resetting restores the switch...
User Guide - Page 20
Switch support auto negotiation is implemented by the higher speed device refraining from... supports transmission between two link partners that enables a port to advertise its transmission rate and duplex mode to its
link partner in order to communicate with higher speed devices. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
...
User Guide - Page 21
Port Status indicates whether the port is linked, not linked or disabled, what speed and duplex mode it is working... of an excessive amount of these frames simultaneously transmitted across a network by a single port. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
If the port security is enabled for all ports. When Layer 2 frames...
User Guide - Page 25
... LAN segment to test the connectedness of the link between VLANs. VLANs are Broadcast and Multicast domains. If the switch is to which the
18 otherwise, the management... switch and destination.
4.4 VLAN Setting
VLANs are logical subgroups with VLANs.
Since VLANs isolate traffic within subgroups. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch ...
User Guide - Page 27
...).Bandwidth of the Trunk is Link Aggregation. There are some ports will not affect the VLAN setting. It optimizes port usage by linking a group of ports together ... (disable, port-based and IEEE802.1p) are provided for this switch family. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
can communicate with any other ports but other ...
User Guide - Page 33
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Figure 5-4 Security Settings Fourthly, Select the "Medium" option of the combo box indicated in the popup menu, a new dialog will display:
Figure 5-5 Resolution Settings 26 Fifthly, right-click the mouse on desktop, select the "Display Properties" in figure 5-4, click the "Reset" ...
User Guide - Page 35
... is linked; a gray icon with SFP are the Giga ports, signed with a black bar indicates that the SFP module hasn't been installed. for the SFP port, a blue icon indicates that the port is the main window to display the status of the ports. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family...
User Guide - Page 37
... File Transfer, Reboot & Reset, and
User. Port Setting: Port Parameter, Port Statistic, Port Status, Storm Control,
and Port Description. Network Setting: Switch IP Address, Static MAC ...Test: Virtual Cable Test.
30 It contains 8 main menus. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
3) On the left side of the ...
User Guide - Page 39
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Figure 5-14 TL-SL2428WEB Main Page
Figure 5-15 TL-SL2452WEB Main Page
5.3.1 System Setting
System setting contains four topics: system information, file transfer, reboot & reset and user. 5.3.1.1 System Information
32
User Guide - Page 41
Figure 5-18 Reboot & Reset
34
otherwise, the switch may
get damaged.
5.3.1.3 Reboot & Reset This page is showed as below. Notice: 1) Please make sure the target file exits on TFTP
server. TFTP Server IP: Indicates the IP address of TFTP server. TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Transfer Type...
User Guide - Page 46
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
127 octets inclusive, including those with errors. RX 128 ...statistic counter has the max numerical value of about 1.8e+19,in excess of this value, the counter will reset to reset all of frames received, not including those with errors. RX Bytes: The sum of bytes of the...
User Guide - Page 47
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
Port Status: Indicates whether the port is linked, not linked, or disabled. Speed (Mbps): Indicates the port speed with the unit of Mbps. Duplex Mode: Indicates the port duplex mode. Flow Control: ...
User Guide - Page 57
TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide
"aging time". The efficiency of packet forwarding is too short causes the table entries to be broadcasted because no ... bound MAC address table are free of the aging time.
5.3.3.7 Ping The ping function is too long lengthens the time of the link between two continuous pings.
50
Similar Questions
Tl-sg2424 V1
Hi there,my question is how to reset the TL-SG2424 v1 switch to factory setings,i am having problem ...
Hi there,my question is how to reset the TL-SG2424 v1 switch to factory setings,i am having problem ...
(Posted by jeanviteza 3 years ago)
Default Ip Address Tl-sg2224web Switch
How can I restore IP address of the TL-SG2224WEB switch on the default value.I have made some change...
How can I restore IP address of the TL-SG2224WEB switch on the default value.I have made some change...
(Posted by minicv 7 years ago)
How To Reset Tp-link Tl-sg1005d
Dear Sirs, As tilte, I would like to know how to reset the TP-Link SG1005d Gigabit switch? Thanks ...
Dear Sirs, As tilte, I would like to know how to reset the TP-Link SG1005d Gigabit switch? Thanks ...
(Posted by cardford 12 years ago)
Tl-sf1008d
8-port Ethernet SwitchesA279; Configuration of TP-Link TL-SF1008D How do i configuration for netw...
8-port Ethernet SwitchesA279; Configuration of TP-Link TL-SF1008D How do i configuration for netw...
(Posted by BapiNandi32 12 years ago)