Samsung SRP-270DP - SRP 270D Two-color Dot-matrix Printer Support and Manuals
Get Help and Manuals for this Samsung item
This item is in your list!
View All Support Options Below
Free Samsung SRP-270DP manuals!
Problems with Samsung SRP-270DP?
Ask a Question
Free Samsung SRP-270DP manuals!
Problems with Samsung SRP-270DP?
Ask a Question
Popular Samsung SRP-270DP Manual Pages
Operation Manual - Page 1
SRP-270 SERIES
1 STATION PRINTER
Operator's Manual
All specifications are subjected to change without notice
Operation Manual - Page 2
... using your local service provider. INTRODUCTION
The SRP-270 Roll Printers are designed to your new SRP-270 series. The main features of the FCC Rules. High speed printing : 4.6 lines per seconds. 2. 2 color dot-matrix printer. 3.
Peripheral units drive circuit enables control of this manual carefully before you should be sure to read the instruction in this...
Operation Manual - Page 9
... used paper roll core if there is one.
To use roll paper that the printer has no un-printed data. " SRP-270 A/C : 1Ply Paper # SRP-270 D : 2Ply Paper
3). This data may be
lost.
2). Roll Paper Installation
Be sure to use a new roll paper, unroll the paper and tear off the end of the paper correctly.
9 3-2. When possible, make sure that matches the printer's specifications.
1).
Operation Manual - Page 10
" SRP-270 A/C : 1Ply Paper # SRP-270 D : 2Ply Paper
10
Put the roll paper on the paper holder and insert the paper in the printer. 4).
Operation Manual - Page 11
Refer to the attached label inside the cover.
6). 5) Insert the end of the roll paper straight into the paper inlet. The printer feeds
the paper automatically and then the printer will cut the paper automatically(SRP-270C type series and SRP-270D type series). Tear off the paper as shown, if necessary.
11
Operation Manual - Page 14
... the word length is 7 bits, you can not parity check OFF status.
14 Serial Interface (RS-232C/RS-485) Specification
DIP Switch 1 Setting
SW
FUNCTION
1 2
Emulation Selection
3
Auto-Cutter
4
FONT SPACE
5
Function for
6
service
7
Engineer
8
RESERVED
ON
OFF
Refer to the following table
Enable 2
Disable 3
Emulation mode selection
SW - 1 OFF OFF ON
SW...
Operation Manual - Page 15
DEFAULT OFF OFF OFF OFF OFF OFF OFF OFF
15
Parallel/USB Interface Specification
DIP Switch 1 Setting
SW
FUNCTION
1 2
Emulation Selection
3
Auto-Cutter
4
FONT SPACE
5
Function for
6
service
7
Engineer
8
RESERVED
ON
OFF
Refer to the following table
Enable 2
Disable 3
DEFAULT OFF OFF OFF OFF OFF OFF
Emulation mode selection
SW - 1 OFF OFF ON
...
Operation Manual - Page 16
... problems. When you turn off . 2. l During the hex dump, all the
codes it receives in hexadecimal format along with a guide ...Set DIP switch 2-2 On. 3. The printer will print all commands except DLE EOT and DLE ENQ are
disabled. Chapter 5. The first column contains the hexadecimal codes and the second column gives the ASCII characters that no ASCII equivalent. After you find specific...
Operation Manual - Page 17
... the DIP switch setting. 4. After printing the current printer status, self-test printing will print the following .
** Character Test Completed **
The printer is ready to continue printing. Press the FEED button to receive data when it completes the self-test.
17 Self-test printing. Make sure paper roll has been installed properly. 2. Turn on...
Operation Manual - Page 28
...code
1B 7A 31 1B 7A 01
0C
1B 64 30
1B 64 31
1B 5F 31 1B 5F 01
1B 5F 30 1B 5F 00
1B 65 31 1B 65 01
1B 65 30 1B 65 00
1B 66 31 1B 66 01
1B 66 30 1B 66 00
Function Set... 1/6 inch line feed
Page feed (form feed) Partial cut Partial cut Select overline mode Cancel overline mode
Set the control panel switch invalid
Set the control panel switch valid
Set the ON LINE switch invalid
Set the ...
Operation Manual - Page 30
...-232C) Pin No. Signal name Direction
1
FG
-
2
TxD
Output
3
RxD
Input
6
DSR
Input
7
SG
-
20
DTR
Output
Function Frame Ground Transmit Data Receive Data Data Set Ready Signal Ground Data Terminal Ready
Serial Communication Interface(Example)
Printer SG TXD RSD DSR DTR
S.G
Host(DTE ex 8251) SG TXD RSD RTS CTS...
Operation Manual - Page 32
.... Signal name
1
Frame ground
2
Drawer kick-out drive signal 1
3
Drawer open/close signal
4
+24V
5
Drawer kick-out drive signal 2
6
Signal ground
Direction Output Input Output -
* SRP-270 Series Model Listing Model Name : SRP-27xyz
x 0 Ivory 5 Dark Gray
y A Basic C Basic
+ Auto cutter D Basic
+ Auto cutter + Spool
32
Blank S P U
z RS-232C RS-485 IEEE-1284 USB
Operation Manual - Page 33
...") 120mm * 63mm * 33mm ( 4.71" * 2.47" * 1.29" ) 215gr ( 0.5 lbs) AD-270 Free Voltage (50Hz ~ 60Hz) Gillotine type Max. 85 mm Max. 0.1mm 4k bytes SRP-270A/AS/AP/AU :
160(W)*249(D)*130(H)mm(6.3"*9.8"*5.12") SRP-270C/CS/CP/CU :
160(W)*249(D)*149(H)mm(6.3"*9.8"*5.87") SRP-270D/DS/DP/DU :
160(W)*294(D)*160(H)mm(6.3"*11.57"*6.3") Weight(printer only...
Operation Manual - Page 34
Allow it to be cool before you reach into the printer.
34 CAUTION : The printer head becomes very hot during printing.
Appendix C
Removing Jammed Paper 1) Open the printer cover 2) Raise the auto cutter unit by lifting the knob lock. 3) Remove the ribbon cassette. 4) Loosen the manual screw. 5) Remove the head cover.
Operation Manual - Page 36
Insert a screw driver into the hole at the bottom side of auto cutter unit as shown followed picture, and turn the gear inside the cutter unit to move the cutter blade to its normal position. NOTE : If you are troubled with reloading the paper, the cutter blade may not be in its normal position.
36
Samsung SRP-270DP Reviews
Do you have an experience with the Samsung SRP-270DP that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Samsung yet.
Earn 750 points for your review!