Samsung SRP-270C - Two-color Dot-matrix Printer Support and Manuals
Get Help and Manuals for this Samsung item
This item is in your list!
View All Support Options Below
Free Samsung SRP-270C manuals!
Problems with Samsung SRP-270C?
Ask a Question
Free Samsung SRP-270C manuals!
Problems with Samsung SRP-270C?
Ask a Question
Popular Samsung SRP-270C Manual Pages
Operation Manual - Page 1
SRP-270 SERIES
1 STATION PRINTER
Operator's Manual
All specifications are subjected to change without notice
Operation Manual - Page 2
... to the instruction manual, may cause harmful interference to receive print data even during printing. 5. Operation of the FCC Rules.
This will be near the equipment and it should turn the printer OFF, and refer to correct the interference at his own expense. NOTE : The power-outlet should be required to your new SRP-270 series.
Operation Manual - Page 3
... B 33 SPECIFICATION 33
APPENDIX C 34 REMOVING JAMMED PAPER 34
3 CONNECTING INTERFACE CABLE AND DRAWER 7
CHAPTER 3. RIBBON CASSETTE INSTALLATION 8 3-2. HEXADECIMAL DUMPING 16
CHAPTER 6. CODE TABLE 18
CHAPTER 8. CHECKING THE CONTENTS OF THE PRINTER BOX 4 1-2. CONNECTING THE AC ADAPTER TO THE PRINTER 6 2-2. CONNECTING THE CABLES 6 2-1. INSTALLING THE ROLL PAPER 8 3-1. THE...
Operation Manual - Page 8
... voided if other than specified ribbon cassettes are used . Before inserting the ribbon cassette, turn the knob clockwise again to prevent
twisting the ribbon.
2). During inserting the ribbon cassette, turn the knob clockwise to
make sure the ribbon moves freely in the printer.
Contact your dealer or place of the ribbon behind the Print Head.
3). Installing the roll paper
3-1.
Operation Manual - Page 9
... cover and remove the used paper roll core if there is one. When possible, make sure that matches the printer's specifications.
1).
3-2. This data may be
lost.
2). To use roll paper that the printer has no un-printed data. " SRP-270 A/C : 1Ply Paper # SRP-270 D : 2Ply Paper
3). Roll Paper Installation
Be sure to use a new roll paper, unroll the paper and tear off the end of the...
Operation Manual - Page 10
4). " SRP-270 A/C : 1Ply Paper # SRP-270 D : 2Ply Paper
10 Put the roll paper on the paper holder and insert the paper in the printer.
Operation Manual - Page 11
Tear off the paper as shown, if necessary.
11 5) Insert the end of the roll paper straight into the paper inlet. Refer to the attached label inside the cover.
6). The printer feeds
the paper automatically and then the printer will cut the paper automatically(SRP-270C type series and SRP-270D type series).
Operation Manual - Page 15
DEFAULT OFF OFF OFF OFF OFF OFF OFF OFF
15
Parallel/USB Interface Specification
DIP Switch 1 Setting
SW
FUNCTION
1 2
Emulation Selection
3
Auto-Cutter
4
FONT SPACE
5
Function for
6
service
7
Engineer
8
RESERVED
ON
OFF
Refer to the following table
Enable 2
Disable 3
DEFAULT OFF OFF OFF OFF OFF OFF
Emulation mode selection
SW - 1 OFF OFF ON
...
Operation Manual - Page 16
Set DIP switch 2-2 On. 3. The first column contains the hexadecimal codes and the second column gives the ASCII characters that correspond to the printer. C
l A period(.) is off. 2. After you find specific commands. Turn on the printer and then the hexadecimal mode is coming to the printer. Run any software program that no ASCII equivalent. l Insufficient print data...
Operation Manual - Page 17
...-test checks whether the printer has any problems. If the printer does not function properly, contact your dealer.
1. Turn on the power while holding down the FEED button.
Self-test printing. The printer prints a pattern using the built-in character set.
6. The self-test automatically ends after printing the following ,
and pause (The PAPER LED light blinks...
Operation Manual - Page 25
... device Cancel user-defined characters Initialize printer Set horizontal tab position Turn emphasized mode on/off Turn double-strike mode on/off Print and feed paper Print and Reverse feed Select an international character set Turn unidirectional printing mode Select justification Select paper sensor to output paper end signals Select paper sensor to stop printing Enable/Disable...
Operation Manual - Page 26
...1B 7B n
1B 65 n 1D 49 n 1D 56 m 1D 56 m n 1D 61 n
1D 72 n
Hexadecimal code 0C + n OA 0E 0F 11 12 13 18 1B, 50, 00 1B, 50, 01 1B,...feed n lines Transmit printer ID Select cut mode and cut paper
Enable/Disable Automatic status back Transmit status
Function
"n" -lines paper feed command Paper feed command Enlarged character command Normal character command Initial set command Inverted character command...
Operation Manual - Page 32
...
VBUS
Red
Host Power
D-
White
Data Line(D-)
D+
Green
Data Line(D+)
GND
Black
Signal Ground
Drawer Connector
Pin No. USB Interface
Pin No.
Signal name
1
Frame ground
2
Drawer kick-out drive signal 1
3
Drawer open/close signal
4
+24V
5
Drawer kick-out drive signal 2
6
Signal ground
Direction Output Input Output -
* SRP-270 Series Model Listing Model Name : SRP-27xyz...
Operation Manual - Page 33
... Million characters Roll paper W76mm ¡ ¾0.5mm (2.99" ¡ ¾0.22")
Max. φ80mm (3.14") 0.06mm ~ 0.085mm (0.002" ~ 0.003") 120mm * 63mm * 33mm ( 4.71" * 2.47" * 1.29" ) 215gr ( 0.5 lbs) AD-270 Free Voltage (50Hz ~ 60Hz) Gillotine type Max. 85 mm Max. 0.1mm 4k bytes SRP-270A/AS/AP/AU :
160(W)*249(D)*130(H)mm(6.3"*9.8"*5.12") SRP-270C/CS/CP/CU :
160(W)*249...
Operation Manual - Page 34
CAUTION : The printer head becomes very hot during printing. Allow it to be cool before you reach into the printer.
34 Appendix C
Removing Jammed Paper 1) Open the printer cover 2) Raise the auto cutter unit by lifting the knob lock. 3) Remove the ribbon cassette. 4) Loosen the manual screw. 5) Remove the head cover.
Samsung SRP-270C Reviews
Do you have an experience with the Samsung SRP-270C that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Samsung yet.
Earn 750 points for your review!