Optoma HD83 Support and Manuals
Optoma HD83 Videos
Popular Optoma HD83 Manual Pages
User's Manual - Page 1
... SYSTEM | Lamp Settings 40 SETUP 41
Appendices 43
Troubleshooting 43 Image Problems 43 Other Problems 45 Remote Control Problems 45 LED Lighting Messages 46 On Screen Messages 47
Replacing the Lamp 48 Compatibility Modes 50 RS232 Commands and Protocol Function List 53
RS232 Pin Assignments 53 RS232 Protocol Function List 54 Ceiling Mount Installation 56 Optoma Global Offices 57...
User's Manual - Page 3
...projector as recommended in operation. Please do not expose this may hurt your local reseller or service center to cool down . Reset the "Lamp Reset" function from the onscreen display "System|Lamp Setting" menu after replacing...Do not look into the projector's lens when the lamp is in this user's guide.
This projector will detect the life of its life, the projector will show on . ...
User's Manual - Page 7
... Remote Battery
Documentation:
User's Manual Warranty Card Quick Start Card WEEE Card
7
English
Introduction
Package Overview
Unpack and inspect the box contents to different applications in the box. If something is missing, please contact Optoma customer service. NOTE
Due to ensure all parts listed below are in each Country...
User's Manual - Page 14
... 3D projector.
PlayStation® 3 Games Make sure that 3D
output is active, 2D video content will not display correctly.
The option is located in sync.
Installation
NOTE
The 3D video source device must be powered on -screen instructions. Insert your 3D game disc. SKY 3D, DirecTV) Contact your TV service...
User's Manual - Page 16
...please check 3D device set up well
to send out 3D image or not. Turn on 3D glasses and verify image appears in the "Display" section of the projector OSD menu.
4. ...(DLP-Link/VESA 3D) of the projector OSD menu. 7. Turn on when input signal is compatible with projector specifications.
3. Installation
NOTE
For more detailed information, please refer to the 3D glasses user's guide,...
User's Manual - Page 17
...
If you can select your source that the "Source Lock" has been set to display on the screen (computer, notebook, video player, etc). Securely connect the ... time you use the projector, you connected multiple sources at the same time, press the "Source" key on the remote control to "SETUP". Installation
Powering On/Off the Projector
Powering On the Projector
. Remove the lens ...
User's Manual - Page 26
...Off / AUTO / On (16:9) / On (2.35:1) DLP-Link / VESA 3D 3D / L / R Off ...Settings
Projection
Test Pattern Background Color 12V Trigger A 12V Trigger B
NOTE
While the 3D is only supported in Analog VGA (RGB) signal.
User Controls
NOTE
Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are only supported...
User's Manual - Page 29
...projector to automatically optimize the display of visible noise interlaced signals.
PureEngine The PureEngine is from "0" to "10". (0: Off)
Gamma This allows you to set up gamma curve type.
Color Settings...for video or TV source. Standard: for standardized setting. Graphics: for image source. After the initial setup and fine tuning is ON, the Dynamic Black function will ...
User's Manual - Page 30
PureEngine Demo This feature enables you make to the PureEngine settings. Use this timing and will be gray out. English
30
The range... | PureEngine
NOTE
While the input source is 120Hz timing, the PureMotion function does not support this mode to check the adjustments that you to "5". PureMotion PureMotion uses sophisticated algorithms to be enhanced thus providing more...
User's Manual - Page 36
Invert" function wouldn't save the setting. It will set to "Off" when powers on non-HDMI 1.4a 3D timing.
Press "Enter" to select 3D format.
3D Format
Off: Press the "...61565; Frame Sequential: Display 3D signal in "Frame Sequential"
format.
English
36 NOTE
"3D sync.
User Controls
NOTE
"3D Format" is only supported on and changes source.
3D Sync.
User's Manual - Page 42
... and Phase items will appear for next time projector turns off of red in the image. Press the ◄ to increase the amount of color in settings after that for user to increase the amount...61558; "Signal" is not supported when the input source is no signal input. (In minutes). Auto Power Off
Set the interval of red and green. Press the ► to manually tune and saved in the image...
User's Manual - Page 43
... 4:3 format DVD title, please change the format as described in projector OSD. If the image is still stretched, you will also need to adjust the
aspect ratio by referring to the "Replacing the Lamp" section. Make sure you experience a problem with your local reseller or service center. Try the different settings.
43
English
User's Manual - Page 54
... - +50
n=1
D50
n=1
D65
n=2
D75
n=4
D83
n=5
D93
n=6
Native
n=7
Native
n=1
DLP cinema
n=2
HDTV
n=3
EBU
n=4
SMPT-C
n=5
n=1
n=2
n=3
n=4
n=5
n=6
-50 ~ 50
n= -50 - +50
-50 ~ 50
n= -50 - +50
n=1
n=1
*RGB (0-255) supports when HDMI is detected
n=2
*RGB(16 - 235)supports when HDMI is for all projectors X
Command ID
X
X
On/Off
Film Video Graphics Standard PureMotion...
User's Manual - Page 55
...Error Fan Lock Over Temperature Lamp Hours Running Out
READ/Return Information from projector
Information
Model Name RS232 Version No
a = Power State
Off\On
b = Lamp Hour
c = Input Source Commands None
VGA
Video
HDMI1
HDMI2
Component
d = Firmware...HD83 Remote command is TBD... Appendices
Function SYSTEM
SETUP Projector ID Reset System Alert
Menu Location
Lamp Setting
Projection Test Pattern ...
User's Manual - Page 57
...
9200 Boulogne Billancourt, France
+33 4 46 2 20 +33 4 46 94 35 savoptoma@optoma.fr
Spain
C/ José Hierro,36 Of. C 28522
Rivas VaciaMadrid,
Spain
+34 9 499 06 06 +34 9 670 08 32
57
English
Appendices
Optoma Global Offices
For service or support please contact your local office. USA
378 Laurelview Ct.
Optoma HD83 Reviews
Do you have an experience with the Optoma HD83 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Optoma yet.
Earn 750 points for your review!