Netgear WAG302 - ProSafe Dual Band Wireless Access Point Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear WAG302 manuals!
Problems with Netgear WAG302?
Ask a Question
Free Netgear WAG302 manuals!
Problems with Netgear WAG302?
Ask a Question
Popular Netgear WAG302 Manual Pages
WAG302v2 Reference Manual - Page 18
... can use the WAG302v2 to gain access to your LAN.
1-2
Introduction
v1.0, May 2006 Operates as a Basic Service Set (BSS). Wireless Repeater. Wireless Access Point. For enhanced security, you specify.
• Upgradeable Firmware. DHCP provides a dynamic IP address to PCs and other bridge-mode wireless stations send all HTTP (TCP, port 80) requests to as a standard...
WAG302v2 Reference Manual - Page 54
... listed in a region other than one of the firmware currently installed.
Shows the IEEE 802.11 wireless operating mode. It may not be legal to operate this field. Indicates if VLAN support is 11. The IP address of the wireless access point's Ethernet port. The default channel setting is enabled. For the frequencies used on the General...
WAG302v2 Reference Manual - Page 62
...to assign wireless clients. There is the IP address of the WAG302v2. The default subnet mask is 255.255.255.0.
• Gateway Address: Enter a Gateway Address for wireless clients connected to this Access Point can assign wireless clients. NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
The following TCP/IP configuration information that the wireless access...
WAG302v1 Reference Manual - Page 2
..., NETGEAR reserves the right to make changes to NETGEAR customer service. Placement...WAG302 Reference Manual (802.11a/g)
Technical Support
Please register to Comply with FCC Standards
FOR HOME OR OFFICE USE
FCC ID: PY3WAG302
This device complies with part 15 of the FCC Rules. Please retain your wireless access point according to http://www.NETGEAR.com. You will find technical support...
WAG302v1 Reference Manual - Page 11
... a wireless capable computer 5-2 I cannot connect to the WAG302 to configure it 5-3 When I enter a URL or IP address I get a timeout error 5-3 Using the Reset Button to Restore Factory Default Settings 5-4 Appendix A Default Settings and Technical Specifications Factory Default Settings A-1 Technical Specifications A-3 Appendix B Related Documents Appendix C Command Line Reference Command...
WAG302v1 Reference Manual - Page 33
Note: By default, WAG302 is NETGEAR-11a. The default wireless access point name is netgearxxxxxx, where xxxxxx represents the last 6 bytes of any wireless access adapters must change this setting. Connect the power adapter to the wireless access point and plug the power adapter in the Advanced Configuration chapter of the WAG302.
4. Verifying Wireless Connectivity
Using a computer with...
WAG302v1 Reference Manual - Page 41
...password- Click Apply to your network Security Profile settings-either the Wireless Settings 11a or Wireless Settings 11b/g. ProSafe Dual Band Wireless Access Point WAG302 Reference Manual (802.11a/g)
• Output Power. From the main menu under Setup, select your network. Verify that the correct Country/ Region in to configure a profile). Select a channel that the correct (default...
WAG302v1 Reference Manual - Page 46
... secondary RADIUS servers: Server Name/IP Address: Primary Secondary Port Shared Secret
2-22
v2.0, May 2006
Basic Installation and Configuration Be sure to set to provide this form and fill in the WAG302. • WEP Encryption Keys. ProSafe Dual Band Wireless Access Point WAG302 Reference Manual (802.11a/g)
SSID and WEP/WPA Settings Setup Form
802.11a Configuration For...
WAG302v1 Reference Manual - Page 54
Configuring WPA with Service Pack 3 or above do include the client software that supports WPA. Nevertheless, the wireless adapter hardware and driver must also support WPA. Enter the RADIUS Server Settings as shown in "Configuring the RADIUS Server Settings" on the menu, select RADIUS Server Settings.
Reconfigure your wireless adapter to match the new settings or access the wireless ...
WAG302v1 Reference Manual - Page 57
... Service Pack 3 or above include the client software that supports WPA. If enabled, associated wireless clients will be able to TKIP+AES.
6. Nevertheless, the wireless adapter hardware and driver must also support WPA. Configuring WPA-PSK
Not all wireless adapters support WPA. ProSafe Dual Band Wireless Access Point WAG302 Reference Manual (802.11a/g)
2. Figure 2-20
Basic Installation...
WAG302v1 Reference Manual - Page 59
....
4. ProSafe Dual Band Wireless Access Point WAG302 Reference Manual (802.11a/g)
3. If enabled, associated wireless clients will be able to communicate with Service Pack 3 or above do include the client software
that supports WPA2. By
default, Data Encryption will not be set to save your client
card supports WPA2. Basic Installation and Configuration
v2.0, May 2006
2-35 Make...
WAG302v1 Reference Manual - Page 67
...IP Settings
IP Address Subnet Mask Default Gateway DHCP Client
The IP address of the wireless access point's Ethernet port.
The default is the default channel setting. (Channel frequencies used by the wireless port of the WAG302... wireless access point.
Identifies the 802.11 operating mode of the firmware currently installed. This information is in a region other screens. It may be...
WAG302v1 Reference Manual - Page 73
...from the NETGEAR website, save it to upload new firmware into the WAG302 must support HTTP uploads, such as shown in a configuration file. The Upgrade Firmware
screen will automatically restart. The upgrade process typically takes about 1 minute. In the Upgrade Firmware menu, click Browse and browse to factory default settings. In some cases, you may fail, corrupt the software, and render...
WAG302v1 Reference Manual - Page 78
... will assign this IP address as the secondary Domain Name Server used by the connected wireless stations.
• Primary WINS Server: The Access Point will assign this IP address as the primary WINS Server used by the connected wireless stations.
4-2
Advanced Configuration
v2.0, May 2006
ProSafe Dual Band Wireless Access Point WAG302 Reference Manual (802.11a...
WAG302v1 Reference Manual - Page 89
...It takes a few seconds for the power indicator to light up -to "Changing the Administrator Password" on the access point. After each problem description, instructions are lit on page 2-3. • I connected the wireless access point correctly? Go to -date WAG302 installation details and troubleshooting guidance visit http://kbserver.netgear.com/products/WG302.asp. Wait a minute and check the...
Netgear WAG302 Reviews
We have not received any reviews for Netgear yet.