NP115 : ceiling plate instruction
Page 1
NEC DISPLAY SOLUTIONS OF AMERICA, INC. Installation and Assembly: Lightweight Adjustable Suspended Ceiling Plate for Projector Mounts Model: SCP200 C U© L US Maximum Load UL Capacity: 60 lb (27.2 kg) ISSUED: 12-16-04 SHEET #: 120-9015-3 11-05-10 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
NEC DISPLAY SOLUTIONS OF AMERICA, INC. Installation and Assembly: Lightweight Adjustable Suspended Ceiling Plate for Projector Mounts Model: SCP200 C U© L US Maximum Load UL Capacity: 60 lb (27.2 kg) ISSUED: 12-16-04 SHEET #: 120-9015-3 11-05-10 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
NP115 : ceiling plate instruction
Page 2
...Maximum UL Load Capacity. • Always use adhesives, lubricants or oils to prevent the screws from loosening, the casing may crack and the projector may fall, causing serious injury and damage to safely lift and position equipment. • Tighten screws firmly, but do not use... an assistant or mechanical lifting equipment to the projector. If you use only. NOTE: Read entire instruction sheet before you have any questions regarding any of the instructions or warnings, call Peerless...
...Maximum UL Load Capacity. • Always use adhesives, lubricants or oils to prevent the screws from loosening, the casing may crack and the projector may fall, causing serious injury and damage to safely lift and position equipment. • Tighten screws firmly, but do not use... an assistant or mechanical lifting equipment to the projector. If you use only. NOTE: Read entire instruction sheet before you have any questions regarding any of the instructions or warnings, call Peerless...
NP115 : ceiling plate instruction
Page 5
... concrete anchors (H) and secure steel cables (E) with wood screw (G) E GE H Truss Ceiling No anchor required. Loop steel cables through cable lock until all attached components (Projector Mount, Extension Column, etc.) and equipment. 5 Insert loose end of steel wire (E) through one way through hole of 6 ISSUED: 12-16-04 SHEET #: 120-9015...
... concrete anchors (H) and secure steel cables (E) with wood screw (G) E GE H Truss Ceiling No anchor required. Loop steel cables through cable lock until all attached components (Projector Mount, Extension Column, etc.) and equipment. 5 Insert loose end of steel wire (E) through one way through hole of 6 ISSUED: 12-16-04 SHEET #: 120-9015...
NP216 : NP01UCM (ceiling mount) instructions
Page 1
Be sure not to the appropriate page for your ceiling installation. IMPORTANT! Turn to touch the projector while tightening the set screw on the ball and socket mount. This may cause the image to be unaligned when you start installation and...page 7 Extension Column ...page 8 Installations: To Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings page 5 To Concrete Ceilings ...page 6 Visit the NEC Web Site at www.necsam.com 1 of the equipment and all attached hardware and components. Installation and Assembly - Universal Ceiling Mount Model: NP01UCM Maximum Load...
Be sure not to the appropriate page for your ceiling installation. IMPORTANT! Turn to touch the projector while tightening the set screw on the ball and socket mount. This may cause the image to be unaligned when you start installation and...page 7 Extension Column ...page 8 Installations: To Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings page 5 To Concrete Ceilings ...page 6 Visit the NEC Web Site at www.necsam.com 1 of the equipment and all attached hardware and components. Installation and Assembly - Universal Ceiling Mount Model: NP01UCM Maximum Load...
NP216 : NP01UCM (ceiling mount) instructions
Page 2
... NEC Projectors Manufacturer NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC Model HT410 HT510 GT1150 GT2150 GT5000 GT6000 GT6000R GT2000 GT2000R GT950 LT10 LT140 LT84 LT150 LT150z LT75 LT75z LT85 LT154 LT155 LT156 LT157 LT158 LT170 LT180 LT220 LT240 LT240K LT245 LT260 LT260K LT265 LT280 LT35 HT1000 HT1100 MT1000 MT1020 MT810 MT820 MT1030 MT1030+ Manufacturer NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC...
... NEC Projectors Manufacturer NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC Model HT410 HT510 GT1150 GT2150 GT5000 GT6000 GT6000R GT2000 GT2000R GT950 LT10 LT140 LT84 LT150 LT150z LT75 LT75z LT85 LT154 LT155 LT156 LT157 LT158 LT170 LT180 LT220 LT240 LT240K LT245 LT260 LT260K LT265 LT280 LT35 HT1000 HT1100 MT1000 MT1020 MT810 MT820 MT1030 MT1030+ Manufacturer NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC...
NP216 : NP01UCM (ceiling mount) instructions
Page 4
... (L) is properly ventilated. If M3 screws are in appearance from the sample illustrated below. Locate adapter plate (L) with projector mount, while keeping the center of Channel Visit the NEC Web Site at least three mounting holes, do not use this adapter plate. Use a combination of screws (M, N, ...O, or P) and foot adjustment that the projector is straight. Tighten all screws with 4 mm security allen wrench (B) or ...
... (L) is properly ventilated. If M3 screws are in appearance from the sample illustrated below. Locate adapter plate (L) with projector mount, while keeping the center of Channel Visit the NEC Web Site at least three mounting holes, do not use this adapter plate. Use a combination of screws (M, N, ...O, or P) and foot adjustment that the projector is straight. Tighten all screws with 4 mm security allen wrench (B) or ...
NP216 : NP01UCM (ceiling mount) instructions
Page 9
...the spring loaded captive screw. Use additional man power or mechanical lifting equipment to just slightly loosen the screw so that your key for projector removal. Push down and tighten the spring loaded captive screw to secure the adapter plate to only use the #10-32 x 3/8" ...turn (about 75°). WOOD JOIST CEILING SET SCREW CAPTIVE SCREW A PROJECTOR 2 1 PROJECTOR ADAPTER PLATE PROJECTOR WARNING • Do not lift more weight than you let go. Visit the NEC Web Site at www.necsam.com 9 of the projector! You should be set screw (shown below . IMPORTANT: Allen wrench ...
...the spring loaded captive screw. Use additional man power or mechanical lifting equipment to just slightly loosen the screw so that your key for projector removal. Push down and tighten the spring loaded captive screw to secure the adapter plate to only use the #10-32 x 3/8" ...turn (about 75°). WOOD JOIST CEILING SET SCREW CAPTIVE SCREW A PROJECTOR 2 1 PROJECTOR ADAPTER PLATE PROJECTOR WARNING • Do not lift more weight than you let go. Visit the NEC Web Site at www.necsam.com 9 of the projector! You should be set screw (shown below . IMPORTANT: Allen wrench ...
Ceiling Plate Technical Data Sheet
Page 1
..., Inc. It shall contain an adjustable collar mount plate with a 1 1/2-11.5 NPS center threaded fitting and holes for a clean finish • Pre-assembled, easy to complement sleek, lightweight projectors. All other brand and product names are trademarks or registered trademarks of the ceiling tray... points (in (48 mm) page 1 of 2 MODEL: SCP200 ARCHITECTS SPECIFICATIONS The Lightweight Adjustable Suspended Ceiling Plate shall be a NEC model CMJ500R1 and shall be mounted above ) with or without an extension column and offers two electrical knockouts. Assembly and installation shall...
..., Inc. It shall contain an adjustable collar mount plate with a 1 1/2-11.5 NPS center threaded fitting and holes for a clean finish • Pre-assembled, easy to complement sleek, lightweight projectors. All other brand and product names are trademarks or registered trademarks of the ceiling tray... points (in (48 mm) page 1 of 2 MODEL: SCP200 ARCHITECTS SPECIFICATIONS The Lightweight Adjustable Suspended Ceiling Plate shall be a NEC model CMJ500R1 and shall be mounted above ) with or without an extension column and offers two electrical knockouts. Assembly and installation shall...
RS232 codes- Projectors
Page 1
.../NP64 Series M300 : M260X/M260W/M300X/M300W Series P420 : P350X/P350W /P420X Series U300 : U300X/U310W Series V300 : V260/V260X/V200X Series Control Commands for NEC Projector (Basic) Rev 4.28.11a Copyright (C) NEC Display Solutions, Ltd. 2002-2011 Updated on April 28, 2011 This file contains information about...
.../NP64 Series M300 : M260X/M260W/M300X/M300W Series P420 : P350X/P350W /P420X Series U300 : U300X/U310W Series V300 : V260/V260X/V200X Series Control Commands for NEC Projector (Basic) Rev 4.28.11a Copyright (C) NEC Display Solutions, Ltd. 2002-2011 Updated on April 28, 2011 This file contains information about...
RS232 codes- Projectors
Page 2
... LT220/240/260. * The serial cable, LAN card and LAN cable are required. 3-2. Projector Control NEC projectors make use the control commands in the standby mode. Setting method : From the projector's menu, select [SETUP] --> [OPTIONS(2)] -->[STANDBY MODE]--> [NORMAL]. ( CAUTION ) (!2) The projector accept the "POWER ON" command during [POWER-SAVING] mode for sending and receiving control...
... LT220/240/260. * The serial cable, LAN card and LAN cable are required. 3-2. Projector Control NEC projectors make use the control commands in the standby mode. Setting method : From the projector's menu, select [SETUP] --> [OPTIONS(2)] -->[STANDBY MODE]--> [NORMAL]. ( CAUTION ) (!2) The projector accept the "POWER ON" command during [POWER-SAVING] mode for sending and receiving control...
RS232 codes- Projectors
Page 5
... in a frame composed of PC 9 4. The response has two types; The frame sent from the controller to the projector is referred to as a command, and the one sent from the projector to the command as NAK) that recognizes a command and Negative Acknowledge (hereafter referred to recognize a command. Command |...mini DIN 8-pin connector. 1 To TxD of PC 2 3 4 To GND of PC 5 6 7 To RxD of PC 8 * 2, 3, 5, 6, and 8 are used inside the projector. [ GT/LT80/MT/NP1000/VT (except VT70/VT80/VT90)/NP3150/NP905/NP600/NP4000/NP3250/NP610/NP2200/NP216/M300/P420/U300/V300 ] The PC CONTROL connector...
... in a frame composed of PC 9 4. The response has two types; The frame sent from the controller to the projector is referred to as a command, and the one sent from the projector to the command as NAK) that recognizes a command and Negative Acknowledge (hereafter referred to recognize a command. Command |...mini DIN 8-pin connector. 1 To TxD of PC 2 3 4 To GND of PC 5 6 7 To RxD of PC 8 * 2, 3, 5, 6, and 8 are used inside the projector. [ GT/LT80/MT/NP1000/VT (except VT70/VT80/VT90)/NP3150/NP905/NP600/NP4000/NP3250/NP610/NP2200/NP216/M300/P420/U300/V300 ] The PC CONTROL connector...
RS232 codes- Projectors
Page 6
... HIGH (not recognized). * ID2: (8 Bit) This is an identification data assigned to each command description.) Response : This returns the value of received ID2 as is. * Projector ID : (8 Bit) This is a projector ID for all others "broadcast notification" is recommended. 1|2|3| 4 |5|6| ~ | n | m 8 | 8 | 8 | 4 | 12 | 8 | ~ | 8 | 8 | | ...This returns the 6th bit of received ID1 as HIGH. For all the projectors. (broadcast notification) This is connected with multiple projectors To control a certain projector, use "individual notification". Command : This sets an identification data assigned ...
... HIGH (not recognized). * ID2: (8 Bit) This is an identification data assigned to each command description.) Response : This returns the value of received ID2 as is. * Projector ID : (8 Bit) This is a projector ID for all others "broadcast notification" is recommended. 1|2|3| 4 |5|6| ~ | n | m 8 | 8 | 8 | 4 | 12 | 8 | ~ | 8 | 8 | | ...This returns the 6th bit of received ID1 as HIGH. For all the projectors. (broadcast notification) This is connected with multiple projectors To control a certain projector, use "individual notification". Command : This sets an identification data assigned ...
RS232 codes- Projectors
Page 7
...: (broadcast notification) CAUTION : * When the model code is set to "broadcast notification", the command becomes broadcast notification command, regardless of values of the projector ID. * Model code is specified using total of 12 bits ( 0 - 4095) of 4 bits of the 4th byte and 8 bits of the ... individually, specifying a model code from the following model codes is required. * Model code: (4 Bit) This is a model code for the projector that sends commands. (individual notification) Entering 0000B or 1111B becomes a common command for all others "broadcast notification" is recommended.
...: (broadcast notification) CAUTION : * When the model code is set to "broadcast notification", the command becomes broadcast notification command, regardless of values of the projector ID. * Model code is specified using total of 12 bits ( 0 - 4095) of 4 bits of the 4th byte and 8 bits of the ... individually, specifying a model code from the following model codes is required. * Model code: (4 Bit) This is a model code for the projector that sends commands. (individual notification) Entering 0000B or 1111B becomes a common command for all others "broadcast notification" is recommended.
RS232 codes- Projectors
Page 13
... REQUEST 015. PICTURE MUTE ON 021. LAMP INFORMATION REQUEST 4 038. LAMP MODE REQUEST 039. PIP/SIDE BY SIDE SET 305.1 BASE MODEL TYPE REQUEST 305.3 PROJECTOR INFORMATION REQUEST Availability by Model (LEGACY MODELS) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 ... firmware version 1.01 or later firmware version 1.02 or later 5. This reflects the "Projector ID" that has been set to the projector. (*2) Model code: "xxH" inscription This will differ depending on the projector. VOLUME ADJUST Volume Bass Treble Balance 030-12. MUTE CONTROL 078-1. AUTO ADJUST EXECUTE2 ...
... REQUEST 015. PICTURE MUTE ON 021. LAMP INFORMATION REQUEST 4 038. LAMP MODE REQUEST 039. PIP/SIDE BY SIDE SET 305.1 BASE MODEL TYPE REQUEST 305.3 PROJECTOR INFORMATION REQUEST Availability by Model (LEGACY MODELS) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 ... firmware version 1.01 or later firmware version 1.02 or later 5. This reflects the "Projector ID" that has been set to the projector. (*2) Model code: "xxH" inscription This will differ depending on the projector. VOLUME ADJUST Volume Bass Treble Balance 030-12. MUTE CONTROL 078-1. AUTO ADJUST EXECUTE2 ...
RS232 codes- Projectors
Page 14
... 60H 70H D0H D0H D0H D0H 80H 80H 90H (*3) Checksum: "CKS" inscription This is the value of the error number at the time of the projector. See "NAK" of the data up to "COMPUTER". 006.
... 60H 70H D0H D0H D0H D0H 80H 80H 90H (*3) Checksum: "CKS" inscription This is the value of the error number at the time of the projector. See "NAK" of the data up to "COMPUTER". 006.
RS232 codes- Projectors
Page 15
... = Power-Off Possible (Normal condition) 1 = Power-Off Impossible Bit 2: Reserved Bit 1: Projector status 0 = Idling 1 = Power On Bit 0: Reserved Response: At the time of the projector. COMMON DATA REQUEST Function: This command acquires all of the detailed conditions of a failure A0H ...007. DATA128 CKS (*1) (*2) (*3) Data Portion Contents DATA01 Projector type See DATA70..71 08H : NP4000 Projector 11H : NP62 Projector DATA02 Projector ID DATA02 1 .. 64 NP4000 1 .. 254 NP62/NP64 1 .. 254 NP216 DATA03 Reserved DATA04 Projector status 00H: Idling 01H: Power On Command: 00H C0H ...
... = Power-Off Possible (Normal condition) 1 = Power-Off Impossible Bit 2: Reserved Bit 1: Projector status 0 = Idling 1 = Power On Bit 0: Reserved Response: At the time of the projector. COMMON DATA REQUEST Function: This command acquires all of the detailed conditions of a failure A0H ...007. DATA128 CKS (*1) (*2) (*3) Data Portion Contents DATA01 Projector type See DATA70..71 08H : NP4000 Projector 11H : NP62 Projector DATA02 Projector ID DATA02 1 .. 64 NP4000 1 .. 254 NP62/NP64 1 .. 254 NP216 DATA03 Reserved DATA04 Projector status 00H: Idling 01H: Power On Command: 00H C0H ...
RS232 codes- Projectors
Page 17
... 00H : Idling 04H : Power On 05H : Cooling 06H : Idling (Error occurrence) Other than above: (nondisclosure) Internal use of code during a state transition period DATA70 .. 71 Projector type
... 00H : Idling 04H : Power On 05H : Cooling 06H : Idling (Error occurrence) Other than above: (nondisclosure) Internal use of code during a state transition period DATA70 .. 71 Projector type
RS232 codes- Projectors
Page 20
... Response: At the time of a success 20H 88H 01H xxH 0CH DATA01 .. ERROR STATUS REQUEST Function: This command acquires the error information occurring with the projector.
... Response: At the time of a success 20H 88H 01H xxH 0CH DATA01 .. ERROR STATUS REQUEST Function: This command acquires the error information occurring with the projector.
RS232 codes- Projectors
Page 21
... the other command during power on the main power of a failure A2H 00H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: The projector does not accept the other command during power off processing. (It contains a cooling period.) 018. Supplement: (!) LT/LT80/HT: "None" 015... 00H 00H 02H Response: At the time of a success 22H 00H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of the projector. POWER ON Function: This command switches on processing. 016. INPUT SW CHANGE Function: This command switches the input terminal or the entry list. Command...
... the other command during power on the main power of a failure A2H 00H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: The projector does not accept the other command during power off processing. (It contains a cooling period.) 018. Supplement: (!) LT/LT80/HT: "None" 015... 00H 00H 02H Response: At the time of a success 22H 00H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of the projector. POWER ON Function: This command switches on processing. 016. INPUT SW CHANGE Function: This command switches the input terminal or the entry list. Command...
RS232 codes- Projectors
Page 28
... (NULL termination character string) DATA50 .. 82 : Reserved DATA83 .. 86 : Lamp Hour Meter (second) (!) DATA87 .. 90 : Filter Usage (second) DATA91 .. 94 : Panel Usage (second) DATA95 .. 98 : Projector Usage (second) Response: At the time of a success 23H 8AH 01H xxH 62H DATA01 .. Aspect Ratio 4:3 (Window) Aspect Ratio Normal / Auto (NP600, NP610, NP2200, NP62... 00H 00H 00H 8DH Response: At the time of a failure A3H 8AH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) INFORMATION REQUEST Function: This command acquires the projector information.
... (NULL termination character string) DATA50 .. 82 : Reserved DATA83 .. 86 : Lamp Hour Meter (second) (!) DATA87 .. 90 : Filter Usage (second) DATA91 .. 94 : Panel Usage (second) DATA95 .. 98 : Projector Usage (second) Response: At the time of a success 23H 8AH 01H xxH 62H DATA01 .. Aspect Ratio 4:3 (Window) Aspect Ratio Normal / Auto (NP600, NP610, NP2200, NP62... 00H 00H 00H 8DH Response: At the time of a failure A3H 8AH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) INFORMATION REQUEST Function: This command acquires the projector information.