Maytag MEDE500WR Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MEDE500WR manuals!
Problems with Maytag MEDE500WR?
Ask a Question
Free Maytag MEDE500WR manuals!
Problems with Maytag MEDE500WR?
Ask a Question
Most Recent Maytag MEDE500WR Questions
Maytag Dryer Service Centennial Won't Run
(Posted by emmmcal 10 years ago)
Maytag Centennial Dryer Wont Turn On
(Posted by merZetsub 10 years ago)
Maytag Centennial Dryer Won't Start
(Posted by dougwsendt 10 years ago)
My Maytag Centennial Medc400vw0 Will Not Start.
My dryer will not start. I have replaced the starter button switch and have no idea what else to do.
My dryer will not start. I have replaced the starter button switch and have no idea what else to do.
(Posted by zachowen 12 years ago)
Popular Maytag MEDE500WR Manual Pages
Owners Manual - Page 5
...
Sensor Cycles automatically match the cycle setting to using your clothes are 80% dry. See "Cycle Setting Chart." 1. Select WRINKLE PREVENT feature, if desired. 4. Press START • PAUSE. 2. NOTE: For the Sanitize Cycle (on some models), do not interrupt the cycle to reduce wrinkles and odors in dryer and shut door. 3.
STEAM CYCLES
Steam Cycles use water...
Owners Manual - Page 6
... minutes of energy. Steam Models
Non-Steam Model
Cycle Control knobs
Sensor Cycles
Sensor Cycles allow you must press the TIME ADJUST up or down buttons. A sensor detects the moisture in the cycle. Sanitize (on all cycles. This cycle should be sanitized. Follow package instructions.
■ Remove the load from the dryer as soon as towels...
Owners Manual - Page 7
...is running, you can form. Steam Cycles
In these cycles, a small amount of 40 minutes. The Steam cycles include Rapid Refresh and ... Air Only setting.
WRINKLE PREVENT Feature
When you can be dried using Air Dry or Air Only. Manual Preset Cycle Settings
Timed Cycles ... Check that part of items that can change the settings for items that require drying without . The dryer will glow ...
Owners Manual - Page 9
... of the manual or contact the dealer from items dried on front edge of drying rack to the following chart). Changing Modifiers and Options after pressing START-PAUSE 1.
NOTE: While cycling through the settings, the current setting will not flash, but the other settings will become your dryer. To find out whether your model allows drying...
Owners Manual - Page 10
... "Assistance or Service" section. A
B
A. 10" (254 mm) pedestal B. 15.5" (394 mm) pedestal
The pedestals are installing your dryer or refer to complete drying, if needed. Do not use Sensor cycles with drawer. Optional Accessories
Pedestals
Are you purchased your PERFORMANCE SERIES washer and dryer and wish to purchase a Stack Kit.
Time* (Minutes)
Wool Sweaters
Timed
Low
60
Block...
Owners Manual - Page 13
... the front and rear edges of the drum for service.
Confirm the exterior vent exhaust hood is free of non-use? Try the following : Clean lint screen.
If the problem continues, call an electrician.
■ Is the valve open on . Electric Dryer displaying code message
■ "L2" Diagnostic Code (low or no line voltage condition): The drum will...
Owners Manual - Page 15
...installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by a Maytag designated service company. Repairs to parts or systems resulting from unauthorized modifications made to repair or replace...
6. Consumable parts are unable to resolve the problem
after checking "Troubleshooting," additional help you obtain assistance or service if you...
Installation Instructions - Page 1
...Requirements 5 Electrical Connection 6
VENTING 11 Venting Requirements 11 Plan Vent System 12 Install Vent System 13
INSTALL LEVELING LEGS 13 CONNECT VENT 14 CONNECT INLET HOSE (STEAM MODELS 14 LEVEL DRYER 15 COMPLETE INSTALLATION 15 TROUBLESHOOTING 15
DRYER SAFETY
Your safety and the safety of injury, and tell you how to potential hazards that can happen if the instructions are...
Installation Instructions - Page 2
...; Tin snips (new vent installations)
■ ¼" nut driver (recommended)
■ Tape measure
■ Pliers
Parts supplied Non-Steam Models
Steam Models
A
B
C
D
E
A. Short inlet hose
D. Rubber washer
Remove parts package from whom you purchased your Use and Care Guide.
2 Check that opens to the "Assistance or Service" section in your dryer. "Y" connector C. NOTE: Do...
Installation Instructions - Page 3
...; Steam models only: Cold water faucets located within 2 ft (610 mm) of either side of 20-100 psi (137.9-689.6 kPa). Do not operate your washer using a power supply cord, a grounded electrical outlet located within 4 ft (1.2 m) of the dryer, and water pressure of the dryer.
Some codes limit, or do not permit, installation of 200 lbs (90.7 kg). Dryer Dimensions...
Installation Instructions - Page 4
...: Some models are not recommended for recessed or closet installation. Dryer only
(460 mm) C
A*
B
Side View
Steam (Electric or Gas)
Non-Steam (Electric or Gas)
A*
1" (25 mm)
1" (25 mm)
B
7 5/8" (194 mm)
7 5/8" (194 mm)
C
3 3/8" (86 mm)
3 3/8" (86 mm)
* Dimension A is approximate, depending on when the diamond marking on pedestal
(460 mm)
A
B
C D*
E
F**
Steam (Electric or...
Installation Instructions - Page 5
... above code standards can be sure that the electrical connection is suitable for stacked recessed or closet installation.
Recommended installation spacing for cabinet installation
NOTE: Some models are not recommended for cabinet installation.
■ For cabinet installation, with a door, minimum ventilation openings in conformance with stacked washer and dryer
The dimensions shown are...
Installation Instructions - Page 11
...
■ Clean lint from your electrical connection.
Tighten screw. Tighten screws. Only rigid or flexible metal vent shall be
used for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to achieve the best drying performance. For more information, see the "Assistance or Service" section. Now go to...
Installation Instructions - Page 13
... metal
27 ft (8.2 m) 21 ft (6.4 m)
Install Vent System
1. Please see the "Assistance or Service" section to achieve the best drying performance. Avoid 90º turns. Do not use a large flat piece of the vent to dryer location. Failure to do so can result in "Plan Vent System." Install exhaust hood. See "Determine vent path" in back or other fastening...
Installation Instructions - Page 15
... still no line voltage condition): The drum will reduce product performance.
Steam Models Only:
10. If there is plugged into a grounded outlet. Check that both fuses are set in the dryer. See "Level Dryer." 6. Replace the fuse or reset the circuit breaker. TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of the water...
Maytag MEDE500WR Reviews
We have not received any reviews for Maytag yet.