Owners Manual
Page 5
Complies with 21CFR 1040.10 and 1040.11 AVOID EXPOSURE-Laser radiation is emitted from this aperture CAUTION LASER RADIATION DO NOT STARE INTO BEAM Maximum Output
Complies with 21CFR 1040.10 and 1040.11 AVOID EXPOSURE-Laser radiation is emitted from this aperture CAUTION LASER RADIATION DO NOT STARE INTO BEAM Maximum Output
Owners Manual
Page 8
...8226; After changing the miter angle, always secure the turn base. Lever 010322 Tilt the saw blade can be locked using positive stops at any desired angle within the specified bevel angle range. Release button 3. When the latch lever is pushed to the back of the saw, the saw blade can be sure...the upper slide pole, turn base while pressing down the lock lever. Adjusting the miter angle 1 1. When tilting the carriage to the right, tilt the carriage to raise the handle fully. NOTICE: • When tilting the saw blade be sure to the left 22.5 ° and 33.9 ° angle...
...8226; After changing the miter angle, always secure the turn base. Lever 010322 Tilt the saw blade can be locked using positive stops at any desired angle within the specified bevel angle range. Release button 3. When the latch lever is pushed to the back of the saw, the saw blade can be sure...the upper slide pole, turn base while pressing down the lock lever. Adjusting the miter angle 1 1. When tilting the carriage to the right, tilt the carriage to raise the handle fully. NOTICE: • When tilting the saw blade be sure to the left 22.5 ° and 33.9 ° angle...
Owners Manual
Page 10
...in overtightening or insufficient tightening of guide fence in compound cutting (bevel angle 45 degrees and miter angle right 45 degrees). Refer to either the left of cutting. B) When you obtain ... the blade, use the wrench may result in serious personal injury. • Use only the Makita socket wrench provided to install or remove the blade.Failure to use the socket wrench to the... • Shift the laser line to see because of the blade (cutting position). Installing or removing saw blade WARNING: • Always be pulled out of the blade. A) When you obtain the correct size...
...in overtightening or insufficient tightening of guide fence in compound cutting (bevel angle 45 degrees and miter angle right 45 degrees). Refer to either the left of cutting. B) When you obtain ... the blade, use the wrench may result in serious personal injury. • Use only the Makita socket wrench provided to install or remove the blade.Failure to use the socket wrench to the... • Shift the laser line to see because of the blade (cutting position). Installing or removing saw blade WARNING: • Always be pulled out of the blade. A) When you obtain the correct size...
Owners Manual
Page 13
... the carriage, install the screw on either the left or right side of the base. Vise rod 1 4. Vise nut 3. When performing 15° or greater miter cuts, install the horizontal vise on the side opposite the direction in which can be thrown and loss of control resulting in two positions on... at any position and pulling or pushing the carriage all the way. Press the workpiece flat against the turn base and guide fence with the saw turned off and unplugged, then check clearance between fences and moving parts. Insert the vise rod into the hole in and out. To grip the...
... the carriage, install the screw on either the left or right side of the base. Vise rod 1 4. Vise nut 3. When performing 15° or greater miter cuts, install the horizontal vise on the side opposite the direction in which can be thrown and loss of control resulting in two positions on... at any position and pulling or pushing the carriage all the way. Press the workpiece flat against the turn base and guide fence with the saw turned off and unplugged, then check clearance between fences and moving parts. Insert the vise rod into the hole in and out. To grip the...
Owners Manual
Page 15
... unexpected kickback resulting in possible serious personal injury. • Never perform the slide cut , before returning the blade to the previously covered "Adjusting the miter angle". 4. NOTICE • When pressing down the handle, apply pressure in parallel with the blade will result in serious personal injury. • The... the entire range of the blade. When the cut is being cut with a vise. When the cut Loosen the lever and tilt the saw blade to set the bevel angle (Refer to a complete stop. Never start the cut on the tool without the blade making any contact ...
... unexpected kickback resulting in possible serious personal injury. • Never perform the slide cut , before returning the blade to the previously covered "Adjusting the miter angle". 4. NOTICE • When pressing down the handle, apply pressure in parallel with the blade will result in serious personal injury. • The... the entire range of the blade. When the cut is being cut with a vise. When the cut Loosen the lever and tilt the saw blade to set the bevel angle (Refer to a complete stop. Never start the cut on the tool without the blade making any contact ...
Owners Manual
Page 16
... should be For outside against guide fence. A 52/38° type 45° type For inside (1) corner (2) For outside (3) corner (4) 006363 Miter angle 52/38° type 45° type Right 31.6° Right 35.3° Left 31.6° Left 35.3° Right 31.6° Right 35...are two common types of crown moldings and one type of the saw angles. A Molding edge against guide fence. When performing compound cutting, refer to "Press cutting", "Slide cutting", "Miter cutting" and "Bevel cut on a compound miter saw with its broad back (hidden) surface down on the turn ...
... should be For outside against guide fence. A 52/38° type 45° type For inside (1) corner (2) For outside (3) corner (4) 006363 Miter angle 52/38° type 45° type Right 31.6° Right 35.3° Left 31.6° Left 35.3° Right 31.6° Right 35...are two common types of crown moldings and one type of the saw angles. A Molding edge against guide fence. When performing compound cutting, refer to "Press cutting", "Slide cutting", "Miter cutting" and "Bevel cut on a compound miter saw with its broad back (hidden) surface down on the turn ...
Owners Manual
Page 17
... of the blade after the cut has been made. 17 A: • Tilt and secure bevel angle setting to 33.9° RIGHT. • Adjust and secure miter angle setting to 31.6° RIGHT. • Lay crown molding with its broad back (hidden) surface down on the turn base with its WALL CONTACT... EDGE against the guide fence on the saw. • The finished piece to be used will be on the corner (4) Wall contact edge should be Left side of cutting 52/38° type...
... of the blade after the cut has been made. 17 A: • Tilt and secure bevel angle setting to 33.9° RIGHT. • Adjust and secure miter angle setting to 31.6° RIGHT. • Lay crown molding with its broad back (hidden) surface down on the turn base with its WALL CONTACT... EDGE against the guide fence on the saw. • The finished piece to be used will be on the corner (4) Wall contact edge should be Left side of cutting 52/38° type...
Owners Manual
Page 18
Compound Miter Saw Miter and Bevel Angle Settings Ceiling 52° 38° Wall Wall to Crown Molding Angle: 52/38 degrees Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 60 43.0 46.8 61 42... 29.0 97 31.5 28.6 98 31.1 28.2 99 30.8 27.7 100 30.4 27.3 Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 101 30.1 26.9 102 29.7 26.5 103 29.4 26.1 104 29.0 25...137 16.8 13.6 138 16.4 13.3 139 16.0 13.0 140 15.6 12.8 EN0002-1 000031 Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 141 15.3 12.3 142 14.9 12.0 143 14.5 11.6 144 14.1 11...
Compound Miter Saw Miter and Bevel Angle Settings Ceiling 52° 38° Wall Wall to Crown Molding Angle: 52/38 degrees Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 60 43.0 46.8 61 42... 29.0 97 31.5 28.6 98 31.1 28.2 99 30.8 27.7 100 30.4 27.3 Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 101 30.1 26.9 102 29.7 26.5 103 29.4 26.1 104 29.0 25...137 16.8 13.6 138 16.4 13.3 139 16.0 13.0 140 15.6 12.8 EN0002-1 000031 Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 141 15.3 12.3 142 14.9 12.0 143 14.5 11.6 144 14.1 11...
Owners Manual
Page 19
Compound Miter Saw Miter and Bevel Angle Settings Ceiling 45° 45° Wall Wall to Crown Molding Angle: 45 degrees Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 60 37.8 50.8 61 37.5 50.2 62 37.3 49.6 63 37.1 49.1 64 36.8 48.5 65 36.6 48.0 66 36.4 ... 14.0 14.4 EN0003-1 Crown molding stoppers (optional accessories) allow easier cuts of crown molding without tilting the saw blade. Install them on the base as shown in the figures. 000032 Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 141 13.7 14.1 142 13.3 13.7 143 13.0 13.3 144 12.6 12.9...
Compound Miter Saw Miter and Bevel Angle Settings Ceiling 45° 45° Wall Wall to Crown Molding Angle: 45 degrees Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 60 37.8 50.8 61 37.5 50.2 62 37.3 49.6 63 37.1 49.1 64 36.8 48.5 65 36.6 48.0 66 36.4 ... 14.0 14.4 EN0003-1 Crown molding stoppers (optional accessories) allow easier cuts of crown molding without tilting the saw blade. Install them on the base as shown in the figures. 000032 Wall Angle Bevel Angle Miter Angle (deg.) (deg.) (deg.) 141 13.7 14.1 142 13.3 13.7 143 13.0 13.3 144 12.6 12.9...
Owners Manual
Page 21
...Loosen the hex sockets bolts securing the guide fence using a triangular rule, try-square, etc. Then securely tighten the hex socket bolts on the miter scale. MAINTENANCE WARNING: • Always be sure that the blade is if the pointer does not point to operator and the upper poles are... locked in the position of the tool which may cause unexpected movement of the saw blade resulting in a serious personal injury. Turn the grip counterclockwise which may cause kickback and result in kickback and serious personal injury. ...
...Loosen the hex sockets bolts securing the guide fence using a triangular rule, try-square, etc. Then securely tighten the hex socket bolts on the miter scale. MAINTENANCE WARNING: • Always be sure that the blade is if the pointer does not point to operator and the upper poles are... locked in the position of the tool which may cause unexpected movement of the saw blade resulting in a serious personal injury. Turn the grip counterclockwise which may cause kickback and result in kickback and serious personal injury. ...
Owners Manual
Page 22
... or three revolutions counterclockwise to tilt the blade to release the positive stops. (1) 0° bevel angle 1. Left 45 ゚ bevel angle adjusting bolt 4. Saw blade 3. by pushing in the lowered position by turning the hex socket bolt on the arm. Make sure that the pointers on the arm holder... the blade with the top surface of the arm holder clockwise. To adjust right 45° bevel angle, perform the same procedure described above. 22 Miter scale 1. Lever 3. If they will point to the left 45° bevel angle, loosen the lever and tilt the blade to 0°. 1. Top ...
... or three revolutions counterclockwise to tilt the blade to release the positive stops. (1) 0° bevel angle 1. Left 45 ゚ bevel angle adjusting bolt 4. Saw blade 3. by pushing in the lowered position by turning the hex socket bolt on the arm. Make sure that the pointers on the arm holder... the blade with the top surface of the arm holder clockwise. To adjust right 45° bevel angle, perform the same procedure described above. 22 Miter scale 1. Lever 3. If they will point to the left 45° bevel angle, loosen the lever and tilt the blade to 0°. 1. Top ...
Owners Manual
Page 25
... Miter saw blades and other non-ferrous metals. 006526 • Vise assembly (Horizontal vise) • Vertical vise • Socket wrench 13 • Holder • Dust bag • Crown molding stopper set • Triangular rule • Dust box • Hex wrench (for LS1016L) MAKITA ... cross grain cuts. EN0006-1 25 Combination Crosscutting General purpose blade for the period of Makita's Factory or Authorized Service Centers. Non-ferrous metals For miters in aluminum, copper, brass, tubing, miter saw blades For smooth and precise cutting in various materials.
... Miter saw blades and other non-ferrous metals. 006526 • Vise assembly (Horizontal vise) • Vertical vise • Socket wrench 13 • Holder • Dust bag • Crown molding stopper set • Triangular rule • Dust box • Hex wrench (for LS1016L) MAKITA ... cross grain cuts. EN0006-1 25 Combination Crosscutting General purpose blade for the period of Makita's Factory or Authorized Service Centers. Non-ferrous metals For miters in aluminum, copper, brass, tubing, miter saw blades For smooth and precise cutting in various materials.
Parts Breakdown
Page 7
258 259 272 275 1,001 1,002 1,003 1,004 1,005 1,006 266042-6 451412-4 942151-2 253313-0 122852-0 122854-6 762001-3 783208-8 782232-8 A-93675 Parts Breakdown TAPPING SCREW BIND CT 4X20, 9046 CASE, LS1016 SPRING WASHER 6, 5007NB THIN WASHER, 4340FCT DUST BAG ASS'Y, LS1016 VISE ASS'Y, LS1016L TRIANGLE RULE, LS1011 HEX WRENCH 2.5, LS1016L BOX WRENCH 13, LS1016 10X5/8 60T MITER SAW BLADE, LS1040 LS1016L 1 1 1 1 1 1 1 1 1 1 Page 7 of 7 8/18/2010
258 259 272 275 1,001 1,002 1,003 1,004 1,005 1,006 266042-6 451412-4 942151-2 253313-0 122852-0 122854-6 762001-3 783208-8 782232-8 A-93675 Parts Breakdown TAPPING SCREW BIND CT 4X20, 9046 CASE, LS1016 SPRING WASHER 6, 5007NB THIN WASHER, 4340FCT DUST BAG ASS'Y, LS1016 VISE ASS'Y, LS1016L TRIANGLE RULE, LS1011 HEX WRENCH 2.5, LS1016L BOX WRENCH 13, LS1016 10X5/8 60T MITER SAW BLADE, LS1040 LS1016L 1 1 1 1 1 1 1 1 1 1 Page 7 of 7 8/18/2010
Flyer (English)
Page 1
... CROWN MOLDING CAPACITY IN ITS CLASS 10" Slide Miter Saw with the Crown Molding Cutting Capacity of a 12" Saw Compact Design with a Patented 4-Steel Rail Sliding System Further Increases Rigidity to Produce Superior Cuts Exclusive 6 Linear Ball Bearings Deliver Smooth, Solid, and ...patented 4-steel rail sliding system deliver dead-on cuts PORTABILITY The most compact design in its class for easy jobsite portability VERSATILITY Models LS1016 / LS1016L 4-3/4" tall dual sliding fence system features upper and lower fence adjustments for more precise cuts LARGE CUTTING CAPACITY makitatools.com
... CROWN MOLDING CAPACITY IN ITS CLASS 10" Slide Miter Saw with the Crown Molding Cutting Capacity of a 12" Saw Compact Design with a Patented 4-Steel Rail Sliding System Further Increases Rigidity to Produce Superior Cuts Exclusive 6 Linear Ball Bearings Deliver Smooth, Solid, and ...patented 4-steel rail sliding system deliver dead-on cuts PORTABILITY The most compact design in its class for easy jobsite portability VERSATILITY Models LS1016 / LS1016L 4-3/4" tall dual sliding fence system features upper and lower fence adjustments for more precise cuts LARGE CUTTING CAPACITY makitatools.com
Flyer (English)
Page 2
...º Crown molding capacity (vertically nested) Base board at makitatools.com, or call 1-800-4MAKITA or visit makitatools.com Makita U.S.A., 14930 Northam St., La Mirada, CA 90638 10" DUAL SLIDE COMPOUND MITER SAW Models LS1016 / LS1016L FEATURES & BENEFITS I Compact design with a patented 4-Steel Rail Sliding System further increases rigidity to produce superior cuts I Exclusive...
...º Crown molding capacity (vertically nested) Base board at makitatools.com, or call 1-800-4MAKITA or visit makitatools.com Makita U.S.A., 14930 Northam St., La Mirada, CA 90638 10" DUAL SLIDE COMPOUND MITER SAW Models LS1016 / LS1016L FEATURES & BENEFITS I Compact design with a patented 4-Steel Rail Sliding System further increases rigidity to produce superior cuts I Exclusive...