LA400 Manual
Page 31
...LIMIT 7 When gate is in the desired position, press the LEARN LIMITS button again. SET OPEN LIMIT SET CLOSE LIMIT The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is Left-handed or Right-handed. Control SET OPEN LIMIT SET... CLOSE LIMIT board will beep. If the problem continues, see Troubleshooting section.) Test the limits by turning the release lever clockwise 180°, then turning the key clockwise...
...LIMIT 7 When gate is in the desired position, press the LEARN LIMITS button again. SET OPEN LIMIT SET CLOSE LIMIT The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is Left-handed or Right-handed. Control SET OPEN LIMIT SET... CLOSE LIMIT board will beep. If the problem continues, see Troubleshooting section.) Test the limits by turning the release lever clockwise 180°, then turning the key clockwise...
LA400 Manual
Page 32
Programming times-out automatically after 60 seconds of inactivity. PROGRAM OPEN 3 Press the LEARN LIMITS button (SET OPEN LIMIT LED will beep. DIAGNOSTIC GATE 1 SET CLOSE 5 Press the GATE 2 right button to be closed first if there is overlap or a gate lock is being used. • The ... OPERATOR) 1 Close the gate. 2 Engage the operator by pressing the SBC to open the left operator. SET OPEN LIMIT SET CLOSE LIMIT The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is overlapping must be set as the primary gate (GATE 1). • If...
Programming times-out automatically after 60 seconds of inactivity. PROGRAM OPEN 3 Press the LEARN LIMITS button (SET OPEN LIMIT LED will beep. DIAGNOSTIC GATE 1 SET CLOSE 5 Press the GATE 2 right button to be closed first if there is overlap or a gate lock is being used. • The ... OPERATOR) 1 Close the gate. 2 Engage the operator by pressing the SBC to open the left operator. SET OPEN LIMIT SET CLOSE LIMIT The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is overlapping must be set as the primary gate (GATE 1). • If...
LA400 Manual
Page 33
...turning the release lever clockwise 180°, then turning the key clockwise 180°. OPEN LIMIT SET CLOSE LIMIT FORCE SET CLOSE The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is now complete. (If the SET OPEN LIMIT LED continues to ... 1 so it will blink). DIAGNOSTIC GATE 1 SET CLOSE 5 Press the GATE 2 left button to open the right operator. Control LIMIT LIMIT FORCE board will beep. If the problem continues, see Troubleshooting section.) Test the limits by pressing the SBC to move the left operator into the OPEN position.
...turning the release lever clockwise 180°, then turning the key clockwise 180°. OPEN LIMIT SET CLOSE LIMIT FORCE SET CLOSE The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is now complete. (If the SET OPEN LIMIT LED continues to ... 1 so it will blink). DIAGNOSTIC GATE 1 SET CLOSE 5 Press the GATE 2 left button to open the right operator. Control LIMIT LIMIT FORCE board will beep. If the problem continues, see Troubleshooting section.) Test the limits by pressing the SBC to move the left operator into the OPEN position.
LA400 Manual
Page 44
... to arm, replace wire if needed. OPERATOR DOES NOT RUN Operator does not respond to resume normal operation. GATE OPENS BUT DOES NOT CLOSE Audible beeps (3 times) when command is given, but the operator does not move. ACCESSORY DEVICE NOT WORKING PROPERLY 1) Not installed properly. 2) Enabling Switch not turned on. 3) Loose...
... to arm, replace wire if needed. OPERATOR DOES NOT RUN Operator does not respond to resume normal operation. GATE OPENS BUT DOES NOT CLOSE Audible beeps (3 times) when command is given, but the operator does not move. ACCESSORY DEVICE NOT WORKING PROPERLY 1) Not installed properly. 2) Enabling Switch not turned on. 3) Loose...