LiftMaster LA400 Support Question
LiftMaster LA400 Support Question
Find answers below for this question about LiftMaster LA400.Need a LiftMaster LA400 manual? We have 3 online manuals for this item!
Question posted by stokescr on March 25th, 2013
Gates Are Open And Will Not Close. I Get 3 Beeps When I Attempt To Close The Ga
Model LA400. Gates will not close. I get 3 beeps when I attempt to close the gates. Which translates to Gate 2 Arm Disengaged. What does that mean and what action can I take?
Current Answers
Related LiftMaster LA400 Manual Pages
LA400 Manual - Page 2
...-to-Open) Attach Brackets to Gate Operator Determine Mounting Location Measuring and Marking for the Gate Bracket Position Gate Operator on Gate Test Gate Travel Secure Post Bracket to Gate Post Secure Gate Bracket to Gate Warning Sign Placement Standard Control Box Large Metal Control Box (XLM)
WIRING
Connect the Gate Operator (Gate 1) to the Control Box Set the Bipart Delay (Model LA400...
LA400 Manual - Page 3
... Type A inherent (built into the operator) entrapment sensing and at least one independent secondary means of the three UL325 classes. Examples include sirens, horns or buzzers. SAFETY » UL325 MODEL CLASSIFICATIONS
CLASS I CLASS II
CLASS III
Swing & Gate Barrier (Arm) Operator
Primary Type A
A, B1 or B2
Secondary Type A, B1 or B2 A, B1, B2 or...
LA400 Manual - Page 6
...gate: • Install warning signs on a dedicated circuit and well protected.
Operator MUST be enclosed in fire. We recommend that time the unit may explode. To AVOID damaging gas...individual.
• DO NOT install ANY wiring or attempt to run in separate conduit.
• BEFORE ... the gate in PLAIN VIEW. • Permanently secure each warning sign in BOTH the open and close gate. ...
LA400 Manual - Page 8
...
CARTON INVENTORY Carton inventory is doubled except for a 90° opening 4 Minutes -20° C to + 50° C -4° F to -Open Bracket (1) • Hex Bolt 5/16"-18 X 1-1/2" (5) &#...8226; Battery (2) • Plug-in Transformer (1)
LA400-S (SECOND GATE OPERATOR ARM)
• Motor Cable - For Primary (Gate 1) and Secondary (Gate 2) installation the carton inventory is based on a Single...
LA400 Manual - Page 12
...Mounting locations vary depending on type and style of the gate operator arm. Gate and gate post MUST be supported entirely by its hinges. B Remove ANY/ALL wheels from the bottom of your gate.
RECOMMENDED: = Gate post bracket mounting locations = Gate bracket mount locations
OPTIONAL: = Gate post bracket mounting locations = Gate bracket mount locations
11 INSTALLATION » CHECK YOUR...
LA400 Manual - Page 16
The gate operator (arm) must be mounted several places on gate for mounting options.
1 Open the gate to -Open bracket and post bracket and secure with clamp. Temporarily secure the gate bracket using a clamp.
4 Align the Pull-to-Open bracket to a position as CLOSE AS POSSIBLE above the screwdriver or dowel rod.
5 Insert hex bolt through Pull-to desired open position...
LA400 Manual - Page 17
...)
SECURE POST BRACKET TO GATE POST The gate operator (arm) must be level.
1 Mark holes for the post bracket.
INSTALLATION » TEST GATE TRAVEL + SECURE POST BRACKET TO GATE POST
TEST GATE TRAVEL
NOTE: If gate does not open and close completely adjust the position of the
1
gate bracket and mark new mounting holes.
1 Manually open and close the gate.
2 Ensure that the...
LA400 Manual - Page 18
... the gate and in plain view.
1 Fasten warning signs to the next page.
17
Inside Property
Moving Gate Can Cause Injury or Death
KEEP CLEAR!
INSTALLATION » SECURE GATE BRACKET TO GATE + WARNING SIGN PLACEMENT
SECURE GATE BRACKET TO GATE The gate operator (arm) must use separate entrance
Some installations may move the gate to verify that it opens and closes...
LA400 Manual - Page 21
...
AC PWR /SOLAR
LOOP INPUTS
20 Lift
the
door
from
the
hinges
and ALARM LOCK GATE 1
setSOL
GND MAGR
LEARN XMITTER
ON
OFF
LOCK /
BIPA RT DELAY
BR
GR
WH
YL
BL
GATE 1
RD
SET OPEN LIMIT
SET CLOSE LIMIT
LEARN LIMITS
aside CLOSE EDGE
OPEN EDGE/ PHOTO
OPEN PHOTO
CLOSE PHOTO
ACCESSORY POWER
12 V
BR GR WH YL...
LA400 Manual - Page 22
...
ACCESSORY POWER
12 V
BR GR WH YL BL RD GATE 2
LEARN XMITTER
ON
OFF
LOCK /
BIPA RT DELAY
CLOSE EDGE
OPEN EDGE/ PHOTO
OPEN PHOTO
SET OPEN LIMIT
GATE 1
CLOSE PHOTO
SET CLOSE LIMIT
LEARN LIMITS
FORCE
GATE 2
ON OFF
AUTO OPEN LOW BATT
OFF MAX
SINGLE BUTTON
TIMER TO CLOSE
OPEN
CONTROL INPUTS
SINGLE BUTTON
RESET
OFF MAX
STOP CTRL PWR...
LA400 Manual - Page 31
... programming times-out automatically after 60 seconds of the control box to the desired OPEN position. SINGLE ARM LEFT-HAND SIDE
PROGRAM OPEN
3 Press the LEARN LIMITS button (SET OPEN LIMIT LED will beep.
LIMIT
LIMIT
5 When gate is in the desired closed position,
SET
press the LEARN LIMITS button again. For proper functionality, the limits must...
LA400 Manual - Page 32
... board
SET
SET
GATE 2
will blink).
SET CLOSE LIMIT
LE LIMIT
GATE 2
FORCE
8 Press the GATE 1 left operator. SET OPEN LIMIT
SET CLOSE LIMIT
The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is overlapping must be set as the primary gate (GATE 1). • If one gate is overlapping the other gate; Programming times-out...
LA400 Manual - Page 33
... LED will beep.
OPEN LIMIT
SET CLOSE LIMIT
FORCE
SET CLOSE
The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is being used. • The programming can be exited at any time by pressing the RESET button.
SET CLOSE LIMIT
LE LIMITS
6 Press the LEARN LIMITS
SET
SET
GATE 2
OPEN
CLOSE
button. LEARN...
LA400 Manual - Page 38
... LOOP INPUT TERMINAL AND COMMON This input functions to the open . Activating this input while the gate is closing gate to reverse a closing gate. Activating this input with a Chamberlain Pulsing Photoelectric Sensor (See Accessories) connected to Terminal P8 while the gate is closing will pause an opening gate until the obstruction has been removed.
The Timer-to...
LA400 Manual - Page 40
... for normal daily operation and you can be disengaged from the gate.
The next command given by pressing the reset button. Reset the control board by remote control or SBC on the control board will close the gate and return the operator to -Close feature is in the open position for any extended period of the...
LA400 Manual - Page 43
...20A 32V
COM
MOV1 JMPR2 DB1
C64 U2
R9 D1
JMPR1
D4 D2
FUSE OPEN
BATT 2 BATT 1
2
OR EDGE
3
OR EDGE
EDGE
CPS-LN4
...MEANING No Stop Switch Connected Gate 1 Arm Disengaged Gate 2 Arm Disengaged Both Gate Arms Disengaged RPM Reversal
# OF BLINKS 6 7 8 9 10
42
MEANING Force Reversal Processor Reset ROM Check Failed RAM Check Failed EEPROM Check Failed - LOOP INPUTS, SAFETY/SHADOW 9. CLOSE...
LA400 Manual - Page 44
... beeps (3 times) when command is given, but the operator does not move.
Clear gate from obstruction.
Move accessories to -Close section for instructions. Clear all Open/Safety devices from obstruction.
Check STOP connections. See Force Adjustment section. See Installation section for proper installation of accessory. Check proper installation of operator arm. GATE...
LA400 Manual - Page 45
...
Alarm (XLM Control Box)
GATE OPERATOR ARM 22
33
ITEM PART #
...DESCRIPTION
QTY
1 41ASWG-442SA
Release Lever
1
2 41ASWG-438SA
Motor with Limit
1
11
Switch Harness
3 41ASWG-0014SA
Rear Connector
1
4 41ASWG-489
Cable 24 V with Connector
1
Not Shown
41ASWG-0119
Release Key
1
K77-19130
Hardware Bag Complete with: Gate bracket, post bracket, Pull-to-Open...
LA400 Manual - Page 47
... mounting hardware. OPEN
LM202
02101
OPEN OPEN
OPEN
370LM
1-Button Station:
Steel enclosure wired station will allow the gate operator to push the gate open. Gate Solenoid Lock: Heavy all steel construction. Fail safe operation keeps gate locked if power is easy to integrate with gate, providing for free exit only. Requires separate power supply (Model ARMP5).
The model LA400 requires two...
LA400 Push to Open Addendum Manual - Page 2
... holes must be level
Fence Post
Gate in OPEN Position
Gate Bracket C Clamp
Gate in Open Position
LEVEL Horizontal Cross Member Mark cross member through middle of gate bracket slots and drill 11/32"... terminals in place at this time (Figures 4 & 6). Install control board and mounting plate. 8. Close cover of post bracket slots (Figure 5).
10. Drill 13/32" holes in place, remove clevis ...
Similar Questions
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Gate Opener Stuck On Stop.
Old liftmaster gate opener LA4000 have power but stop light is on and can't get it to work?Diagnosti...
Old liftmaster gate opener LA4000 have power but stop light is on and can't get it to work?Diagnosti...
(Posted by emadxnick 2 years ago)
Does It Have Myq And If So Can Garage Door Be Opened/closed From A Remote Locati
does it have MyQ and if so can garage door be opened/closed from a remote location with smart phone
does it have MyQ and if so can garage door be opened/closed from a remote location with smart phone
(Posted by neilgoldschmitt 6 years ago)
Open Learn Limit Button Closes Gate And Close Button Opens Gate
Installed new circuit board due to lighting. programing learn limits (open) button will close the ga...
Installed new circuit board due to lighting. programing learn limits (open) button will close the ga...
(Posted by maryannh 12 years ago)