Forms and Bar Code Technical Reference
Page 56
MaxiCode examples Here are 3 extra fields that must follow these rules: • For all modes, the input data must be 3 digits in AIM spec). Mode 3, separated with commas: ESC&y48W1,1,40361,840,001,This is the secondary message. A specific and limited set A as defined in length and thus padded ...
MaxiCode examples Here are 3 extra fields that must follow these rules: • For all modes, the input data must be 3 digits in AIM spec). Mode 3, separated with commas: ESC&y48W1,1,40361,840,001,This is the secondary message. A specific and limited set A as defined in length and thus padded ...
Forms and Bar Code Technical Reference
Page 91
...); Determines the model of module element, in length, padded with standard error correction An array of -labels field. size of QR symbology used in AIM spec). Arguments for MaxiCode bar code symbology Key /Symbology /Mode /QuietZone Range 02-06 (dec) Default value /MaxiCode 02 (dec) Description Symbology identification 02 = Structured carrier...
...); Determines the model of module element, in length, padded with standard error correction An array of -labels field. size of QR symbology used in AIM spec). Arguments for MaxiCode bar code symbology Key /Symbology /Mode /QuietZone Range 02-06 (dec) Default value /MaxiCode 02 (dec) Description Symbology identification 02 = Structured carrier...
Forms and Bar Code Technical Reference
Page 156
...This section describes deviations in this Technical Reference considers as "HP BDP"), or the Lexmark Bar Code Card version 2.5. (referred to this encoding, each character. However, the HRT is operating per the specs at the URLs noted above. Therefore, the Forms and Bar Code Card firmware must...will then generate the proper uppercase characters within the bar code. Refer to: • http://www.makebarcode.com/specs/code_93.html • http://www.makebarcode.com/specs/code_39.html The HP BDP converts lowercase "a-z" character input to the BCE. This will also be uppercase, reflecting ...
...This section describes deviations in this Technical Reference considers as "HP BDP"), or the Lexmark Bar Code Card version 2.5. (referred to this encoding, each character. However, the HRT is operating per the specs at the URLs noted above. Therefore, the Forms and Bar Code Card firmware must...will then generate the proper uppercase characters within the bar code. Refer to: • http://www.makebarcode.com/specs/code_93.html • http://www.makebarcode.com/specs/code_39.html The HP BDP converts lowercase "a-z" character input to the BCE. This will also be uppercase, reflecting ...
Forms and Bar Code Technical Reference
Page 157
... a per bar code, input data with large amounts of encodable data will fail, usually with large amounts of encoding data. There is operating per the specs noted above, and does not translate lowercase to uppercase. This table is approximately 20-25 characters. Invalid Character" error. The LXK BCC also performs the...
... a per bar code, input data with large amounts of encodable data will fail, usually with large amounts of encoding data. There is operating per the specs noted above, and does not translate lowercase to uppercase. This table is approximately 20-25 characters. Invalid Character" error. The LXK BCC also performs the...
Forms and Bar Code Technical Reference
Page 161
... 3, corresponding to MaxiCode Mode 2 or Mode 3 Mode 2 encodes numeric-only data, and Mode 3 allows a reduced amount of the input data to the BCE. The HP spec BarDIMM specification version 3.0 (and all versions from 3.0 onward are : • A number 1 through 8, that examines input data: • Byte 5 for a separator character If they can decode...
... 3, corresponding to MaxiCode Mode 2 or Mode 3 Mode 2 encodes numeric-only data, and Mode 3 allows a reduced amount of the input data to the BCE. The HP spec BarDIMM specification version 3.0 (and all versions from 3.0 onward are : • A number 1 through 8, that examines input data: • Byte 5 for a separator character If they can decode...