2560/3060 Operation Guide (Advanced Edition)
Page 233
... Adjust printing quality and conduct machine maintenance. • Copy Density Adjustment ...6-63 • Print Density ...6-64 • Send/Box Density Adjust ...6-64 • Auto Drum Refresh ...6-65 • Drum Refresh ...6-66 • Correcting Fine Black Lines ...6-67 • Display Brightness ...6-68 • Silent Mode ...6-68 • Auto Color Correction...6-69 • System...
... Adjust printing quality and conduct machine maintenance. • Copy Density Adjustment ...6-63 • Print Density ...6-64 • Send/Box Density Adjust ...6-64 • Auto Drum Refresh ...6-65 • Drum Refresh ...6-66 • Correcting Fine Black Lines ...6-67 • Display Brightness ...6-68 • Silent Mode ...6-68 • Auto Color Correction...6-69 • System...
2560/3060 Operation Guide (Advanced Edition)
Page 235
... by monitoring its peripheral temperature and humidity. The table below shows the available settings. Auto Drum Refresh performed as needed (Refer to execute Auto Drum Refresh. NOTE: You can also execute Drum refresh as Long 6 (maximum 180 seconds). Item Off Standard Long Description No Auto...from the low power mode or sleep mode. Cancel OK 10/10/2007 10:10 ADVANCED OPERATION GUIDE 6-65 Auto Drum Refresh performed as Standard (maximum 140 seconds). Auto Drum Refresh is turned on page 6-66.) 1 Press the System Menu key. 2 Press [T], [Adjustment/Maintenance] and [...
... by monitoring its peripheral temperature and humidity. The table below shows the available settings. Auto Drum Refresh performed as needed (Refer to execute Auto Drum Refresh. NOTE: You can also execute Drum refresh as Long 6 (maximum 180 seconds). Item Off Standard Long Description No Auto...from the low power mode or sleep mode. Cancel OK 10/10/2007 10:10 ADVANCED OPERATION GUIDE 6-65 Auto Drum Refresh performed as Standard (maximum 140 seconds). Auto Drum Refresh is turned on page 6-66.) 1 Press the System Menu key. 2 Press [T], [Adjustment/Maintenance] and [...
2560/3060 Operation Guide (Advanced Edition)
Page 236
...normal and does not indicate a fault. Use the procedure below to the Adjustment/Maintenance screen. 6-66 ADVANCED OPERATION GUIDE Item Drum Refresh 1 Drum Refresh 2 Description Use this mode when white spots appear on the ejected paper is done. The toner soiling on images.... 10/10/2007 10:10 6 Once Drum Refresh ends, return to refresh the drum. 1 Place 11 × 17" or A3 on images in copies. Adjustment/Maintenance Drum Refresh 1: Execute Drum Refresh 2: Auto Drum Refresh: Standard Change Main Charger Cleaning : Drum Refresh will be performed while printing. Use...
...normal and does not indicate a fault. Use the procedure below to the Adjustment/Maintenance screen. 6-66 ADVANCED OPERATION GUIDE Item Drum Refresh 1 Drum Refresh 2 Description Use this mode when white spots appear on the ejected paper is done. The toner soiling on images.... 10/10/2007 10:10 6 Once Drum Refresh ends, return to refresh the drum. 1 Place 11 × 17" or A3 on images in copies. Adjustment/Maintenance Drum Refresh 1: Execute Drum Refresh 2: Auto Drum Refresh: Standard Change Main Charger Cleaning : Drum Refresh will be performed while printing. Use...
2560/3060 Operation Guide (Advanced Edition)
Page 297
... of these conditions will not only deliver poor copies but may also cause jams and shorten the useful life of printing and may damage the drum or fusing unit. Condition Avoid using paper with a smooth and even surface; Ingredient Do not use paper such as it may damage the... drum. Supported Paper Sizes Paper of cotton or other fibers. Corner angles must be 90° ± 0.2°. Be sure to use paper that has a rough ...
... of these conditions will not only deliver poor copies but may also cause jams and shorten the useful life of printing and may damage the drum or fusing unit. Condition Avoid using paper with a smooth and even surface; Ingredient Do not use paper such as it may damage the... drum. Supported Paper Sizes Paper of cotton or other fibers. Corner angles must be 90° ± 0.2°. Be sure to use paper that has a rough ...
2560/3060 Operation Guide (Advanced Edition)
Page 302
... edge raised a few times with a ruler. The adhesive layer contains materials that stick to feed labels from the carrier sheet. Label Be sure to the drum or rollers and peeled labels remaining in the output tray at once. If paper jams occur, load fewer envelopes at once. To prevent paper jams...
... edge raised a few times with a ruler. The adhesive layer contains materials that stick to feed labels from the carrier sheet. Label Be sure to the drum or rollers and peeled labels remaining in the output tray at once. If paper jams occur, load fewer envelopes at once. To prevent paper jams...
2560/3060 Operation Guide (Advanced Edition)
Page 309
...-10 Additional Memory Appendix-10 Adjustment/Maintenance 6-63 Auto Color Corrcection 6-69 Copy Density Adjustment 6-63 Correcting Fine Black Lines 6-67 Display Brightness 6-68 Drum Refresh 6-66 Print Density 6-64 Send/Box Density 6-64 Silent Mode 6-68 Appendix Appendix-1 AppleTalk 6-58, Appendix-10 Setup 6-58 Auto... Drum Refresh 6-65 Auto Form Feed Timeout Appendix-10 Auto Image Rotation 1-48 Auto Paper Selection Appendix-10 Auto Sleep Mode Appendix-10 B Booklet from ...
...-10 Additional Memory Appendix-10 Adjustment/Maintenance 6-63 Auto Color Corrcection 6-69 Copy Density Adjustment 6-63 Correcting Fine Black Lines 6-67 Display Brightness 6-68 Drum Refresh 6-66 Print Density 6-64 Send/Box Density 6-64 Silent Mode 6-68 Appendix Appendix-1 AppleTalk 6-58, Appendix-10 Setup 6-58 Auto... Drum Refresh 6-65 Auto Form Feed Timeout Appendix-10 Auto Image Rotation 1-48 Auto Paper Selection Appendix-10 Auto Sleep Mode Appendix-10 B Booklet from ...
2560/3060 Operation Guide (Basic Edition)
Page 16
...the MFP or an accessory is authorized to furnish labor. 2. Kyocera Mita America, Inc. For model KM-2560 - and for the name and address of the drum unit, the fixing unit, and the developing unit which are not genuine Kyocera brand parts or supplies, (c) have been serviced by a technician ...not employed by Kyocera or an Authorized Kyocera Dealer, or (d) have no ...
...the MFP or an accessory is authorized to furnish labor. 2. Kyocera Mita America, Inc. For model KM-2560 - and for the name and address of the drum unit, the fixing unit, and the developing unit which are not genuine Kyocera brand parts or supplies, (c) have been serviced by a technician ...not employed by Kyocera or an Authorized Kyocera Dealer, or (d) have no ...