Instruction Manual
Page 1
... to read through this instruction manual. Familiarity with installation and operation procedures will help you call upon your Kenwood dealer for information or service on the warranty card, and in the space provided below. KDC-X492 KDC-MP438U KDC-MP408U KDC-MP338 CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D'EMPLOI REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE...
... to read through this instruction manual. Familiarity with installation and operation procedures will help you call upon your Kenwood dealer for information or service on the warranty card, and in the space provided below. KDC-X492 KDC-MP438U KDC-MP408U KDC-MP338 CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D'EMPLOI REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE...
Instruction Manual
Page 2
...device, and CD-R/RW as "audio files." Playing AAC, MP3, and WMA data This document refers to control these data. and other countries. • The "AAC" logo is a trademark of Apple Inc., registered in the U.S. See (page 16) for KDC-X492 is used ...Appendix 16 Accessories/ Installation Procedure 18 Connecting Wires to Terminals 19 Installation 20 Troubleshooting Guide 21 Specifications 23 Panel illustrations used to describe operations in this document The control panel for details. • iPod is trademark of Dolby Laboratories. 2 | KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338
...device, and CD-R/RW as "audio files." Playing AAC, MP3, and WMA data This document refers to control these data. and other countries. • The "AAC" logo is a trademark of Apple Inc., registered in the U.S. See (page 16) for KDC-X492 is used ...Appendix 16 Accessories/ Installation Procedure 18 Connecting Wires to Terminals 19 Installation 20 Troubleshooting Guide 21 Specifications 23 Panel illustrations used to describe operations in this document The control panel for details. • iPod is trademark of Dolby Laboratories. 2 | KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338
Instruction Manual
Page 3
... or outside rim has burrs, use a CD with tape stuck on the Demonstration mode. Wiping the faceplate with a hard cloth or using a volatile liquid such as a silicon cloth. This unit may scratch the surface or erases characters. • If you experience problems during installation, consult your Kenwood dealer. • When you turn on...
... or outside rim has burrs, use a CD with tape stuck on the Demonstration mode. Wiping the faceplate with a hard cloth or using a volatile liquid such as a silicon cloth. This unit may scratch the surface or erases characters. • If you experience problems during installation, consult your Kenwood dealer. • When you turn on...
Instruction Manual
Page 16
...m4a), MP3 (.mp3), WMA (.wma) • Playable disc media CD-R/RW/ROM • Playable disc file format ISO 9660 Level 1/2, Joliet, Romeo, Long file name. • USB device Playable Model KDC-X492, KDC-MP438U, KDC-MP408U • Playable USB device USB mass storage class • ...Playable USB device file system FAT16, FAT32 • iPod Playable Model KDC-X492, KDC-MP438U Although the audio files are complied with the standards ...
...m4a), MP3 (.mp3), WMA (.wma) • Playable disc media CD-R/RW/ROM • Playable disc file format ISO 9660 Level 1/2, Joliet, Romeo, Long file name. • USB device Playable Model KDC-X492, KDC-MP438U, KDC-MP408U • Playable USB device USB mass storage class • ...Playable USB device file system FAT16, FAT32 • iPod Playable Model KDC-X492, KDC-MP438U Although the audio files are complied with the standards ...
Instruction Manual
Page 18
... wire should be connected to this unit. wires or ground them to any Kenwood disc changers/ CD players released in turn may have an ACC position, connect the ignition wires to a rear output terminal. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. Refer to both the front... to the system, connect the connectors either to both the rear output terminals (do not remove the caps on the car are being connected. 18 | KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 Always connect those wires to direct sunlight or excessive heat or humidity.
... wire should be connected to this unit. wires or ground them to any Kenwood disc changers/ CD players released in turn may have an ACC position, connect the ignition wires to a rear output terminal. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. Refer to both the front... to the system, connect the connectors either to both the rear output terminals (do not remove the caps on the car are being connected. 18 | KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 Always connect those wires to direct sunlight or excessive heat or humidity.
Instruction Manual
Page 20
...The frame can be removed from the catch pins on each side, as shown in place. Japanese cars 1 Refer to drop it. 20 | KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 If the unit is unstable, it may skip). Upper the frame and pull it in the figure. Lock Catch Bend the tabs of... 2 Remove the screw (M4 × 8) on the back panel. 3 Insert the two removal tools deeply into the slots on the upper level. Installation non-Japanese cars Metal mounting strap (commercially available) Firewall or metal support Removing the hard rubber frame 1 Engage the catch pins on the removal tool...
...The frame can be removed from the catch pins on each side, as shown in place. Japanese cars 1 Refer to drop it. 20 | KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 If the unit is unstable, it may skip). Upper the frame and pull it in the figure. Lock Catch Bend the tabs of... 2 Remove the screw (M4 × 8) on the back panel. 3 Insert the two removal tools deeply into the slots on the upper level. Installation non-Japanese cars Metal mounting strap (commercially available) Firewall or metal support Removing the hard rubber frame 1 Engage the catch pins on the removal tool...
Instruction Manual
Page 23
... Preout level / Load (CD) KDC-X492 : 4000 mV/10 kΩ KDC-MP438U/MP408U/MP338 : 2500 mV/10 kΩ Preout impedance : ≤ 600 Ω Auxiliary input Frequency response (±1 dB) : 20 Hz - 20 kHz Input Maximum Voltage : 1200 mV Input Impedance : 10 kΩ General Operating voltage (11 - 16V allowable) : 14.4 V Current consumption : 10 A Installation Size (W x H x D) : 182...
... Preout level / Load (CD) KDC-X492 : 4000 mV/10 kΩ KDC-MP438U/MP408U/MP338 : 2500 mV/10 kΩ Preout impedance : ≤ 600 Ω Auxiliary input Frequency response (±1 dB) : 20 Hz - 20 kHz Input Maximum Voltage : 1200 mV Input Impedance : 10 kΩ General Operating voltage (11 - 16V allowable) : 14.4 V Current consumption : 10 A Installation Size (W x H x D) : 182...
Instruction Manual
Page 68
... 1040. 10, CHAPTER 1, SUBCHAPTER J. These limits are reproductions of the following are designed to radio or television reception, which the receiver is not installed and used in accordance with Federal Regulations, following measures: • Reorient or relocate the receiving antenna... approved in the instruction manual. Location : Bottom Panel In compliance with the instructions. Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. Changes or modifications to this equipment if an unauthorized change or modification is encouraged...
... 1040. 10, CHAPTER 1, SUBCHAPTER J. These limits are reproductions of the following are designed to radio or television reception, which the receiver is not installed and used in accordance with Federal Regulations, following measures: • Reorient or relocate the receiving antenna... approved in the instruction manual. Location : Bottom Panel In compliance with the instructions. Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. Changes or modifications to this equipment if an unauthorized change or modification is encouraged...