Installation Manual
Page 1
DDX418 DDX4048BT DDX318 DDX3048 MONITOR WITH DVD RECEIVER INSTALLATION MANUAL MONITEUR AVEC RÉCEPTEUR DVD MANUEL D'INSTALLATION MONITOR CON RECEPTOR DVD MANUAL DE INSTALACIÓN © 2010 Kenwood Corporation All Rights Reserved. LVT2199-005A (KN/RN)
DDX418 DDX4048BT DDX318 DDX3048 MONITOR WITH DVD RECEIVER INSTALLATION MANUAL MONITEUR AVEC RÉCEPTEUR DVD MANUEL D'INSTALLATION MONITOR CON RECEPTOR DVD MANUAL DE INSTALACIÓN © 2010 Kenwood Corporation All Rights Reserved. LVT2199-005A (KN/RN)
Installation Manual
Page 2
... the reset button. 9 Perform the Initial Setup. (Refer to the Instruction Manual.) After the Installation After the installation, perform the Initial Setup by referring to the power source running through the fuse box. •... wires in the following order: ground, battery, ignition. 5 Connect the wiring harness connector to the unit. 6 Install the unit in a spot exposed to a power source with a constant voltage supply, such as with battery wires...one with the same rating. 2 DDX418/DDX4048BT/DDX318/DDX3048 If you connect the ignition wire to direct sunlight or excessive heat or humidity.
... the reset button. 9 Perform the Initial Setup. (Refer to the Instruction Manual.) After the Installation After the installation, perform the Initial Setup by referring to the power source running through the fuse box. •... wires in the following order: ground, battery, ignition. 5 Connect the wiring harness connector to the unit. 6 Install the unit in a spot exposed to a power source with a constant voltage supply, such as with battery wires...one with the same rating. 2 DDX418/DDX4048BT/DDX318/DDX3048 If you connect the ignition wire to direct sunlight or excessive heat or humidity.
Installation Manual
Page 3
... to work if you connect the + connector of the left speaker to a front output terminal, do not remove the caps on the panel surface when installing the unit to decrease the internal temperature. Do not mount the unit in malfunction. Bluetooth adaptor (KS-UBT1) ¤ CAUTION... Install this unit during and shortly after the use of your vehicle. English 3 To prevent a short circuit, do not connect the - Do not touch the metal ...
... to work if you connect the + connector of the left speaker to a front output terminal, do not remove the caps on the panel surface when installing the unit to decrease the internal temperature. Do not mount the unit in malfunction. Bluetooth adaptor (KS-UBT1) ¤ CAUTION... Install this unit during and shortly after the use of your vehicle. English 3 To prevent a short circuit, do not connect the - Do not touch the metal ...
Installation Manual
Page 6
...utensil and attach it in place. ⁄ • Make sure that the unit is installed securely in the same manner. 2 When the lower level is unstable, it forward as shown in the figure. Installation on Toyota, Nissan or Mitsubishi Car using Brackets Accessory 3 (M5x6mm) or Accessory 4 (...be removed from the top side in place. Lower the frame and pull it may malfunction (eg, the sound may skip). Installation/Removing the Unit Installing the Unit Installing the Escutcheon 1 Attach accessory 5 to the unit. If the unit is removed, remove the upper two locations. 6 DDX418/DDX4048BT...
...utensil and attach it in place. ⁄ • Make sure that the unit is installed securely in the same manner. 2 When the lower level is unstable, it forward as shown in the figure. Installation on Toyota, Nissan or Mitsubishi Car using Brackets Accessory 3 (M5x6mm) or Accessory 4 (...be removed from the top side in place. Lower the frame and pull it may malfunction (eg, the sound may skip). Installation/Removing the Unit Installing the Unit Installing the Escutcheon 1 Attach accessory 5 to the unit. If the unit is removed, remove the upper two locations. 6 DDX418/DDX4048BT...
Installation Manual
Page 7
...careful to avoid injury from the catch pins on the place shown above. Installing the Microphone Unit (DDX418/DDX4048BT only) 1 Check the installation position of the microphone (accessory 7). 2 Remove oil and other dirt from the installation surface. 3 Install the microphone. 4 Wire the microphone cable up to the unit with it... with a commercial item of the microphone to drop it secured at several positions using tape or the like. ⁄ • Install the microphone as far as shown. Adjust the direction of tape. Removing the Unit 1 Remove the escutcheon by referring to the removal...
...careful to avoid injury from the catch pins on the place shown above. Installing the Microphone Unit (DDX418/DDX4048BT only) 1 Check the installation position of the microphone (accessory 7). 2 Remove oil and other dirt from the installation surface. 3 Install the microphone. 4 Wire the microphone cable up to the unit with it... with a commercial item of the microphone to drop it secured at several positions using tape or the like. ⁄ • Install the microphone as far as shown. Adjust the direction of tape. Removing the Unit 1 Remove the escutcheon by referring to the removal...