Image Fitness 3.8 Support and Manuals
Get Help and Manuals for this Image Fitness item
View All Support Options Below
Free Image Fitness 3.8 manuals!
Problems with Image Fitness 3.8?
Ask a Question
Free Image Fitness 3.8 manuals!
Problems with Image Fitness 3.8?
Ask a Question
Popular Image Fitness 3.8 Manual Pages
English Manual - Page 1
....imagefitness.com
new products, prizes, fitness tips, and much more! Model No. 831.159700 Serial No.
Serial Number Decal (under seat)
®
USER'S MANUAL
SEARS, ROEBUCK AND CO. Write the serial number in this manual before using this manual for reference. HOFFMAN ESTATES, IL 60179
CAUTION
Read all precautions and instructions in the space above for...
English Manual - Page 2
Remove the Part List/Exploded Drawing before beginning assembly.
2 Table of Contents
Important Precautions 3 Before You Begin 4 Part Identification Chart 5 Assembly 6 Adjusting the Weight Bench 14 Ordering Replacement Parts Back Cover Full 90-Day Warranty Back Cover Note: A Part List/Exploded Drawing is attached in the center of this manual.
English Manual - Page 3
... or any worn parts immediately.
6. Replace any exercise program, consult your weights (not included) with pre-existing health problems. Read all parts each side of the barbell.
10. Always move the bench out of the way when performing an exercise that all instructions in the location shown.
7. Apply the decal in this manual.
2. Important Precautions
WARNING...
English Manual - Page 4
Whether your benefit, read this manual carefully before calling. Central Time (excluding holidays).
The model number is designed to help you achieve the specific results you , please note the product model number and serial number before using the IMAGE® 3.8 weight bench.
They do not refer to right and left side" are labeled. Left Side Upright...
English Manual - Page 6
... so the large hole is in the box above.
By setting aside plenty of time, and by anyone. Note: Some small parts may be more convenient if you assemble them, unless instructed to the included allen wrench , assembly requires the following information and instructions:
Make Things Easier for Yourself! Before beginning, make sure all...
English Manual - Page 8
... the Weight Storage Tube (21), the left Upright (1) with two M10 x 70mm Bolts (46), a Small Support Plate (16), and two M10 Nylon Locknuts (11). Press a 25mm Round Inner Cap (51) into the...While a second person continues to the right Upright (1) with two M10 x 70mm Bolts (46), a Small Support Plate (16), and two M10 Nylon Locknuts (11).
Do not tighten the Nylon Locknuts yet.
51
46
21...
English Manual - Page 9
....
9
11
18
34 32
Handle 24
54
52
1
62 7
Hole 39
Note: Tilt the Weight Guide away from the Upright (1) as you have correctly identified the left end. Secure the Weight Glider to make... (29) into each end of the round tube on top of the
8
Locking Bar (34). Insert a Weight Guide (18) into each end of the Left Safety Spotter (24). Secure the Weight Glider to the Base (7) with ...
English Manual - Page 10
...point toward the center of the bench.
Attach the other Weight Guide (18) to the Base (7) with a Large Washer (...38) and an M8 Washer (52). Insert a Weight Guide (18) into the indentation in the 50mm Bushing (47)...16mm Screws used in steps 1 to tilt the Weight Guide away from the Upright (1) as you do not ...
Attach the upper end of one of the Weight Guides (18) to the Barbell with an M8 x ...
English Manual - Page 12
...
6
11
15 27
21.
Attach the Backrest Tubes (27) to the indicated side of the Seat Support Tube (37). the Seat Adjustment Bracket must pivot easily.
20. Note: Do not overtighten the Nylon ... on the Bench Frame (5) so that the Seat Adjustment Bracket (45) fits over -
6
tighten the Nylon Locknut; Attach the Seat Support Tube (37) to the Backrest Tubes (27)
20
with the Bolt and...
English Manual - Page 13
... the bracket on the following page.
13 Turn the Seat (14) as shown. 23. Make sure that all remaining parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the Seat Support Tube (37) with an M6 x 38mm Bolt (60) and an M6
37
Washer (30).
30 3
60
24. Attach the...
English Manual - Page 14
... with weight clips when they are on one of the slot in the Uprights (1). WARNING: Always set both hands. To do this, stand in front of the cage and grip the Locking
1
Bar...(35).
Always place the same amount of the Barbell. Replace any worn parts immediately. Do not use the weight bench. See the included exercise guide for that
exercise. Secure the weights with the Large Weight ...
English Manual - Page 16
... x 60mm Spacer
58
1
25mm x 50mm Inner Cap
59
4
M8 x 65mm Carriage Bolt
60
1
M6 x 38mm Bolt
61
1
Right Spotter Hook
62
1
Left Spotter Hook
#
1
User's Manual
#
1
Exercise Guide
#
1
6mm Allen Wrench
Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. Qty. Part List-Model No. 831.159700
R1299A
Key No.
English Manual - Page 17
...
48
44 43
47
17 40
16
46 1
11
2
6
6 42
21 46
54 52 51
11
17
7
12
41 59 52
39
R1299A
Exploded Drawing-Model No. 831.159700
English Manual - Page 18
... need to schedule repair
service call the following information:
• The MODEL NUMBER of the product (831.159700)
• The NAME of the product (IMAGE 3.8 Weight Bench)
• The PART NUMBER of the PART (see the PART LIST and the EXPLODED DRAWING at the center of this manual to the frame. This warranty gives you specific legal rights, and...
Image Fitness 3.8 Reviews
We have not received any reviews for Image Fitness yet.