User Guide
Page 34
Infoprint 1332/1352/1372 Tools required Flat-blade screwdrivers, various sizes Phillips screwdrivers, various sizes 7.0 mm nut driver 5.5 mm wrench Needlenose pliers Diagonal side cutters Spring hook Feeler gauges Analog or digital multimeter Parallel wrap plug 1319128 Twinax/serial debug cable 1381963 Flash light (optional) 1-14 Service Manual
Infoprint 1332/1352/1372 Tools required Flat-blade screwdrivers, various sizes Phillips screwdrivers, various sizes 7.0 mm nut driver 5.5 mm wrench Needlenose pliers Diagonal side cutters Spring hook Feeler gauges Analog or digital multimeter Parallel wrap plug 1319128 Twinax/serial debug cable 1381963 Flash light (optional) 1-14 Service Manual
User Guide
Page 38
...64. 917 Transfer Roll Indicates a problem in an intermittent condition when you can POR the printer to "Fuser service checks" on page 2-41. 901 Engine Flash Indicates that the flash ...page 2-94. 920 Fuser Error Indicates that the fuser is below temperature when printing. Infoprint 1332/1352/1372 Messages and error codes Service error codes Service error codes are indications that... Replace the system board. 903 Paperport Link Driver Error 904 Interface Violation by RIP 905 Interface Violation by Paperport Device 906 RIP Interface Driver Error 910 DC Pick Motor DC Error Codes ...
...64. 917 Transfer Roll Indicates a problem in an intermittent condition when you can POR the printer to "Fuser service checks" on page 2-41. 901 Engine Flash Indicates that the flash ...page 2-94. 920 Fuser Error Indicates that the fuser is below temperature when printing. Infoprint 1332/1352/1372 Messages and error codes Service error codes Service error codes are indications that... Replace the system board. 903 Paperport Link Driver Error 904 Interface Violation by RIP 905 Interface Violation by Paperport Device 906 RIP Interface Driver Error 910 DC Pick Motor DC Error Codes ...
User Guide
Page 114
...: • Install another print cartridge if available before proceeding with the mirror motor circuit in the printer. An incorrect printer driver for the media being used. • Test the printer using plain paper (20 lb). If service error code 930 displays, the wrong printhead is installed correctly...system board. If correct, replace the printhead assembly. The voltage at J5-7 measures approximately +24 V dc. Infoprint 1332/1352/1372 Printhead service check The printhead assembly does not contain any print quality problems do the following menu settings as indicated....
...: • Install another print cartridge if available before proceeding with the mirror motor circuit in the printer. An incorrect printer driver for the media being used. • Test the printer using plain paper (20 lb). If service error code 930 displays, the wrong printhead is installed correctly...system board. If correct, replace the printhead assembly. The voltage at J5-7 measures approximately +24 V dc. Infoprint 1332/1352/1372 Printhead service check The printhead assembly does not contain any print quality problems do the following menu settings as indicated....
User Guide
Page 160
The reference adjustment screw can be removed from the printer. Back the reference adjustment screw out far enough to allow the alignment assembly to the left margin. Infoprint 1332/1352/1372 Paper alignment assembly adjustment Do the alignment assembly adjustment whenever you check the diamonds on the ...two screws holding the alignment assembly to be adjusted without loosening the nut. Turn the reference screw clockwise with a 7 mm nut driver until you obtain the results you are set correctly. 1. It is necessary to back the reference adjustment screw out far enough to...
The reference adjustment screw can be removed from the printer. Back the reference adjustment screw out far enough to allow the alignment assembly to the left margin. Infoprint 1332/1352/1372 Paper alignment assembly adjustment Do the alignment assembly adjustment whenever you check the diamonds on the ...two screws holding the alignment assembly to be adjusted without loosening the nut. Turn the reference screw clockwise with a 7 mm nut driver until you obtain the results you are set correctly. 1. It is necessary to back the reference adjustment screw out far enough to...