IBM 28P1938 - InfoPrint 1140 B/W Laser Printer Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 28P1938 Manual Pages
User Guide - Page 23
... and safety instructions.
2. Repair Information provides instructions for service personnel. It is designed for making printer adjustments and removing and installing FRUs.
5. General Information contains a general description of printer problems.
4. Parts Catalog contains illustrations and part numbers for individual FRUs. Diagnostic Information contains an error indicator table...
User Guide - Page 29
... DC Pick Motor below speed
913 DC Pick Motor over speed
2-2 Service Manual If jumpers are set correctly, replace the system board.
905 Interface Violation by the controller software
Check for the model/type printer you can cause a 902 service error. IBM Infoprint 1130/1140
Service Error Codes
Service Error Codes are generally non-recoverable except in an intermittent condition when you...
User Guide - Page 61
... continues.
The flash is formatted.
2-34 Service Manual The flash is resolved. This error may occur at power on . If a 1200 dpi job runs out of the page has been reduced from 600 dpi to 300 dpi to print.
Flash operations are not resolution reduced. IBM Infoprint 1130/1140
User Message Primary
36 Resolution Reduced
User...
User Guide - Page 95
... continuity of the sensor.
2-68 Service Manual If the cable does not measure continuity, replace the cable.
Note: Check the fuser envelope conditioner solenoid adjustment as the sensor flag is attached between 5 ohms and 10
ohms. If incorrect, replace the
solenoid assembly. A different setting may correct the problem. Input Sensor Service Check
Service Tip: Run the Base Sensor...
User Guide - Page 116
... the fixed disk and the fixed disk board are correctly installed. IBM Infoprint 1130/1140
Hard Disk Option
Service Tip: The Lexmark T printers support one hard disk option is installed.
• 3.2 GB or larger
Check to make sure only one hard disk option. If the test fails, replace the hard disk. The "Disk Test/Clean" on the...
User Guide - Page 121
... the failing sensor. If incorrect, replace the sensor assembly. Note: Before performing the following checks run the Output Bin X Sensor Test and check for proper operation. The voltage measures approximately +5 V dc.
IBM Infoprint 1130/1140
Remove Paper - Sensor Test: NF = Near Full (Upper part of sensor assembly) F = Full (Lower part of paper feeds into Output...
User Guide - Page 125
... or damaged parts. Repair as necessary.
IBM Infoprint 1130/1140
202 Paper Jam Open Rear Door Message displays and a sheet of paper is jammed prior to the pass through sensors. The voltage measures approximately 0 V dc. If incorrect, replace the mechanical linkage assembly/DC Motor Assembly.
2-98 Service Manual A 202 paper jam message can help isolate the problem. If...
User Guide - Page 126
...operation, binding, broken parts or interference from the sensor cable. If incorrect, replace the sensor assembly. Diagnostic Information 2-99 If incorrect,
repair as necessary. FRU
...installed before attempting to service the unit.
Disconnect the pass thru sensor cable and check the voltage at J3-2. If incorrect, repair as necessary.
271 Paper Jam - IBM Infoprint 1130/1140...
User Guide - Page 128
...
Action
Check the flag for correct operation, binding, broken parts or interference from the sensor cable. If incorrect, repair as necessary. The voltage measures approximately 0 V dc. The voltage measures approximately +5 V dc. If this does not fix the problem, replace the lower control board. Check Bin 4 displays
Service Tip: When a 274 Paper Jam Check Bin 4 message...
User Guide - Page 135
... assembly. The voltage at J7-7 measures approximately +24 V dc. IBM Infoprint 1130/1140
Printhead Service Check
The printhead assembly does not contain any service replaceable parts or components.
If incorrect, replace the system board. If correct, replace the printhead assembly.
These error codes indicate a problem with the mirror motor circuit in the printer. If incorrect...
User Guide - Page 148
... or improper installation of the smart cartridge cable to the system board. The voltage measures approximately +3.8 V dc when not writing data to troubleshoot the printer....replace the system board.
The voltage measures approximately +5 V dc. IBM Infoprint 1130/1140
Smart Cartridge Contact Assembly Service Check
Note: If you are unable to clear a "32-Unsupported Cartridge" User Error...
User Guide - Page 150
... voltage at J10-12. If correct, replace the toner sensor assembly. Transfer Roll Service Check
Service Tip: The transfer roll is part of connector J25 on the toner sensor results in a 929 service error.
IBM Infoprint 1130/1140
FRU 3 Toner Sensor
Action
The toner sensor cable is part of the front harness and part of the Maintenance Kit and is...
User Guide - Page 196
... the Configuration menu.
• The following is installed. Select Maintenance Page Count value from the menu. 4. To reset the Maintenance Count, press Select for =Reset.
Press Return to go to the previous menu.
IBM Infoprint 1130/1140
Maintenance Page Count
This counter is reset by the servicer after a "80 Scheduled Maintenance" message displays (300K...
User Guide - Page 197
... help correct print quality problems.
Fuser Temperature
This adjustment can be adjusted as required. The leftmost digit blinks indicating that it does so in the EP Setup menu to validate the Configuration ID.
The factory sets the warm up at 0 or no warm up before the ID redisplays. IBM Infoprint 1130/1140
-
Note: When the...
User Guide - Page 308
... non-Lexmark attachments
Lubrication Specifications
Lubricate only when parts are replaced or as needed, not on a scheduled basis.
Use IBM no. 10 oil, P/N 1280443 (Approved equivalents: Mobil DTE27, Shell Tellus 100, Fuchs Renolin MR30), IBM no. 23 grease (Approved equivalent Shell Darina 1), and grease, P/N 53P8774 to aid you correct the hazard. IBM Infoprint 1130/1140
6. Following these...
IBM 28P1938 Reviews
We have not received any reviews for IBM yet.