Designjet L26500 Error Codes

HP Designjet L26500 printer series - Maintenance and troubleshooting guide - English

Page 71
... roll. ● Otherwise, follow the special procedure described in the front panel, with one of several error codes (see the above steps until the front panel displays the Ready message. If you see Front-panel error messages on page 80). Turn off the printer at the front panel, then also switch off the...

HP Designjet L26500 printer series - Maintenance and troubleshooting guide - English

Page 87
...sure that all fans are within printer specifications. Then try again to resolve the error. Follow the advice in this list, turn off the printer and then turn it . Table 10-2 Numeric error messages Error code Recommendation 15.01:00 15.02:00 The printer is unable to warm up ...have selected the correct firmware update file. if the problem persists, call your cable connections. See When you need help on . PDL Error: parsing error The print job is not included in the Recommendation column to perform the update. Change the loaded substrate type or the print settings....

HP Designjet L26500 printer series - Maintenance and troubleshooting guide - English

Page 88
...the Move substrate key. Open the printhead cleaning cartridge door on page 86. 21.2:10 Printhead cleaning cartridge error. Error messages 82 Chapter 10 Front-panel error messages ENWW If the problem persists, call your service representative. Check that all take -up reel cables are...When you need help on page 86. 32:01 The take -up reel is within printer specifications. Table 10-2 Numeric error messages (continued) Error code Recommendation 15.03:00 Excessive heat in the curing module. Check that all fans are working and unblocked. If the problem...

HP Designjet L26500 printer series - Maintenance and troubleshooting guide - English

Page 89
...the substrate adjustment lever and clear the obstruction. If necessary, use the take -up reel arrow keys to resume printing. 32:01.2 This error occurs when there is attached to wind the substrate; If the problem persists, call your service representative. See When you try to enable the...have forgotten to set the switch direction or tape the substrate to the take -up reel spindle; Table 10-2 Numeric error messages (continued) Error code Recommendation 32:01.1 This error occurs when there is noise in the signal of the waste management system. and that the take -up reel switch is...

HP Designjet L26500 printer series - Maintenance and troubleshooting guide - English

Page 90
... the printer. See When you need help on page 8. If the problem persists, call your service representative. Table 10-2 Numeric error messages (continued) Error code Recommendation 61:01 The file format is correctly installed in the RIP. ● Resubmit the file to the printer. ● ... When you need help on page 8. Check that all relevant cables are properly connected, and check whether the RIP has displayed any error messages. If the problem persists, call your service representative. See When you are long pauses of the printer. Try the following remedies...

HP Designjet L26500 printer series - Maintenance and troubleshooting guide - English

Page 91
...you go to display on page 86. 82:01 There may be a substrate jam, or a dirty carriage reflector. Table 10-2 Numeric error messages (continued) Error code Recommendation 76:03 A "disk out of roll has been detected. Try the following remedies: ● Turn off the printer by using... update on the printer. ● Check that there are no substrate preset for any visible obstacles restricting the movement of recent system errors, warnings, or printhead or ink cartridge events. If the problem persists, call your service representative. Disconnect the power cord, then reconnect...

HP Designjet L26500 printer series - Maintenance and troubleshooting guide - English

Page 93
...Embedded Web Server when you can request specific parts of which takes a significant time to request the whole list (select All pages). see Front-panel error messages on page 80 ◦ The RIP you are using, and its current status, some of it down; There are using : the product.../ webAccess/allServicePlot.htm. You can produce on the Web: please visit http://welcome.hp.com/ country/us/en/wwcontact_us.html. or you select Help > About Telephone number Your HP Support telephone number is an error code on a label at the rear of your printer into a Web browser, followed by E-mail. If...

Designjet L26500 Error Codes - HP